Fedoseyev, A. I. | Engineering Papers

NASA NTRS2002

Minimizing Segregation During the Controlled Directional Solidification of Dendritic Alloys Publication: Metallurgical and Materials Transactions

Gravity-driven thermosolutal convection that arises during controlled directional solidification (DS) of dendritic alloys promotes detrimental macro-segregation (e.g. freckles and steepling) in products such as turbine blades. Considerable time and effort has been spent to experimentally and theoretically investigate this phenomena; although our knowledge has advanced to the point where convection can be modeled and accurately compared to experimental results, little has been done to minimize its onset and deleterious effects. The experimental work demonstrates that segregation can be. minimized and microstructural uniformity promoted when a slow axial rotation is applied to the sample crucible during controlled directional solidification processing. Numerical modeling utilizing continuation and bifurcation methods have been employed to develop accurate physical and mathematical models with the intent of identifying and optimizing processing parameters.

Grugel, R. N.↗

NASA NTRS2001

Solidification Processing of Immiscible Liquids in the Presence of Applied Ultrasonic Energy

Uniform microstructural distribution during solidification of immiscible liquids (e.g., oil and water; aluminum and lead) on Earth is hampered by inherent density differences between the phases. Microgravity processing minimizes settling but segregation still occurs due to gravity independent wetting and coalescence phenomena. Experiments with the transparent organic, metal analogue, succinonitrile-glycerol system were conducted in conjunction with applied ultrasonic energy. The processing parameters associated with this technique have been evaluated in view of optimizing dispersion uniformity. Characterization of the experimental results in terms of a modeling effort will also be presented,

Grugel, R. N.↗

NASA NTRS2001

Characterizing the Use of Ultrasonic Energy in Promoting Uniform Microstructural Dispersions in Immiscible Mixtures

Gravity driven separation and preferential wetting precludes uniform microstructural distributions during solidification processing of immiscible, liquid-liquid mixtures. Historically, it is, however, established that liquid/liquid suspensions can be established and maintained by utilizing ultrasound. Following a brief introduction the results of experiments on immiscible mixtures subjected to ultrasonic energy during solidification processing will be compared and evaluated in view of a recently developed mathematical model. The presentation continues by discussion of scaling the model to commercial viability and concludes with the implications of such processing in a microgravity environment.

Grugel, R. N.↗

NASA NTRS2001

Novel Directional Solidification of Hypermonotectic Alloys

There are many metal alloy systems that separate into two different liquids upon cooling from a higher temperature. Uniform microstructural development during solidification of these immiscible liquids on Earth is hampered by inherent density differences between the phases. Microgravity processing minimizes settling but segregation still occurs due to gravity independent wetting and coalescence phenomena. Experiments with the transparent organic, metal analogue, succinonitrile-glycerol system were conducted in conjunction with applied ultrasonic energy. The processing parameters associated with this technique have been evaluated in view of optimizing dispersion uniformity. Characterization of the experimental results in terms of an initial modeling effort will also be presented.

Grugel, R. N.↗

NASA NTRS2001

Some Novel Solidification Processing Techniques Being Investigated at MSFC: Their Extension for Study Aboard the ISS

The float-zone and the Bridgman techniques are two classical directional solidification processing methods that are used to improve materials properties. Unfortunately, buoyancy effects and gravity-driven convection due to unstable temperature and/or composition gradients still produce solidified products that exhibit segregation and, consequently, degraded properties. This presentation will briefly introduce how some novel processing applications can minimize detrimental gravitational effects and enhance microstructural uniformity. Discussion follows that to fully understand and model these procedures requires utilizing, in conjunction with a novel mixing technique, the facilities and quiescent microgravity environment available on the ISS.

Grugel, R. N.↗

NASA NTRS2000

Magnetic Field Suppression of Flow in Semiconductor Melt

One of the most promising approaches for the reduction of convection during the crystal growth of conductive melts (semiconductor crystals) is the application of magnetic fields. Current technology allows the experimentation with very intense static fields (up to 80 KGauss) for which nearly convection free results are expected from simple scaling analysis in stabilized systems (vertical Bridgman method with axial magnetic field). However, controversial experimental results were obtained. The computational methods are, therefore, a fundamental tool in the understanding of the phenomena accounting during the solidification of semiconductor materials. Moreover, effects like the bending of the isomagnetic lines, different aspect ratios and misalignments between the direction of the gravity and magnetic field vectors can not be analyzed with analytical methods. The earliest numerical results showed controversial conclusions and are not able to explain the experimental results. Although the generated flows are extremely low, the computational task is a complicated because of the thin boundary layers. That is one of the reasons for the discrepancy in the results that numerical studies reported. Modeling of these magnetically damped crystal growth experiments requires advanced numerical methods. We used, for comparison, three different approaches to obtain the solution of the problem of thermal convection flows: (1) Spectral method in spectral superelement implementation, (2) Finite element method with regularization for boundary layers, (3) Multiquadric method, a novel method with global radial basis functions, that is proven to have exponential convergence. The results obtained by these three methods are presented for a wide region of Rayleigh and Hartman numbers. Comparison and discussion of accuracy, efficiency, reliability and agreement with experimental results will be presented as well.

Fedoseyev, A. I.↗

NASA NTRS2000

Characterizing the Use of Ultrasonic Energy in Promoting Uniform Composite Growth in Immiscible Alloys

The results of experimental investigation and mathematical modeling for immiscible alloys subjected to ultrasonic influence are presented. It is known that in inoculated light alloy melts, ultrasonic treatment creates a new type of cast structure with extremely fine grains of uniform composition. This effect is produced across a wide range of freezing rates and technologies. However, it has not been demonstrated that the process can be successfully applied during controlled directional solidification processing. In this work we present the results from a set of directional solidification experiments and suggest describing the droplet size versus ultrasonic frequency and amplitude using an energy approach, followed with a more detailed analysis through numerical modeling of the ultrasonic field.

Grugel, Richard N.↗

NASA NTRS2000

Novel Directional Solidification of Hypermonotectic Alloys

There are many metal alloy systems that separate into two different liquids upon cooling from a higher temperature. Uniform microstructural development during solidification of these immiscible liquids on Earth is hampered by inherent density differences between the phases. Microgravity processing minimizes settling but segregation still occurs due to gravity independent wetting and coalescence phenomena. Experiments with the transparent organic, metal analogue, succinonitrile-glycerol system were conducted in conjunction with applied ultrasonic energy. The processing parameters associated with this technique have been evaluated in view of optimizing dispersion uniformity. Characterization of the experimental results in terms of an initial modeling effort will also be presented.

Grugel, Richard N.↗

NASA NTRS2000

Modeling of Ultrasonically Generated Liquid-Liquid Dispersions During Controlled Directional Solidification

There are innumerable two-component systems in which two very different liquid phases co-exist in equilibrium over a range of temperature and composition, e.g., oil and water, salt fluxes and solders, aluminum and lead. Often it is of practical concern to fabricate a solid component consisting of a uniform dispersion of one phase in the other. Unfortunately, uniform microstructural development during solidification of two immiscible liquids is hampered by inherent, often large, density differences between the phases that lead to severe segregation. Uniformity is also compromised by preferential wetting and coalescence phenomena. It is, however, well known that ultrasonic energy can initiate and maintain a fine liquid-liquid dispersion. The work presented here extends that observation by application of ultrasonic energy to promote uniform phase incorporation during controlled directional solidification. To this end experiments with the transparent organic, immiscible, succinonitrile-glycerol system were conducted and the numerous processing parameters associated with this technique were evaluated in view of optimizing dispersion uniformity. In view of the initial experimental results a model that predicts the dispersed liquid droplet size as a function of material properties, sample geometry, and applied energy has been developed. In the mathematical model we consider the ultrasonic field in an experimental ampoule of length L and diameter D induced by a probe having a vibration frequency of f=2OKhz (circular frequency omega = 2 pi f). The amplitude is adjustable from A=65 to 13Omicrons. The probe tip diameter is d, the liquid has a density of p, in which the speed of sound and surface tension are, respectively, c and sigma. The mathematical model and numerical investigation for the experiments [1] is done using the following assumptions: (i) The droplet size is small in comparison to the sound wave length; (ii) The forces between droplets are neglected (relative concentration is small); (iii) The droplet is stable if the kinetic energy, E(sub K), of the liquid motion due to ultrasonic field influence is less then the binding energy, E(sub S), due to the surface tension (it is easy to show that the surface energy of two droplets resulting from one is larger by about a factor of two.); (iv) The stability limit is characterized by E(sub S) to approx. E(sub K).

Grugel, R. N.↗

NASA NTRS2000

An Experimental and Mathematical Study to Evaluate the Role of Ultrasonic Energy in Promoting Microstructural Uniformity During Controlled Directional Solidification Processing

There are many commercially relevant metal and non-metal "alloy" systems that separate into two different liquids upon cooling from a higher temperature. Consequently during solidification processing the inherent density differences between the two liquid phases leads to rapid, gravity driven, separation and severe segregation, a factor that significantly compromises the desired material properties. Processing in a microgravity environment minimizes settling but segregation still occurs due to gravity independent wetting and coalescence phenomena. This presentation reports on experiments that utilized succinonitrile-glycerol mixtures, a transparent system that 1) separates into two liquids upon cooling and 2) is also well established as an analogue to solidification phenomena observed in metals. Segregation was significantly reduced when the mixtures were subjected to ultrasonic energy during directional solidification processing. The processing parameters introduced by this application have been evaluated in view of optimizing dispersion uniformity. The improvement is in good agreement with a novel model that 1) predicts the achievable size of the droplets as a function of applied ultrasonic energy and then 2) calculates their relative sinking velocity through the bulk liquid.

Grugel, R. N.↗

NASA NTRS2000

Characterizing the Use of Ultrasonic Energy in Promoting Uniform Microstructural Dispersions in Immiscible Mixtures

Gravity driven separation and preferential wetting precludes uniform microstructural distributions during solidification processing of immiscible, liquid-liquid mixtures. Historically, it is, however, established that liquid/liquid suspensions can be established and maintained by utilizing ultrasound. Following a brief introduction the results of experiments on immiscible mixtures subjected to ultrasonic energy during solidification processing will be compared and evaluated in view of a recently developed mathematical model. The presentation continues by discussion of scaling the model to commercial viability and concludes with the implications of such processing in a microgravity environment.

Grugel, R. N.↗