Engineering Papers⌕ Search

Engineering topics

Fedors, R. F.

Publications and source records attributed to Fedors, R. F..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Analysis of the tensile stress-strain behavior of elastomers at constant strain rates. I - Criteria for separability of the time and strain effects

A theoretical analysis of the tensile stress-strain relation of elastomers at constant strain rate is presented which shows that the time and the stress effect are separable if the experimental time scale coincides with a segment of the relaxation modulus that can be described by a single power law. It is also shown that time-strain separability is valid if the strain function is linearly proportional to the Cauchy strain, and that when time-strain separability holds, two strain-dependent quantities can be obtained experimentally. In the case where time and strain effect are not separable, superposition can be achieved only by using temperature and strain-dependent shift factors.

Hong, S. D.↗
NASA NTRS1981

Photomechanical transducer

Light absorbing ultra-thin films mounted under a fixed strain exhibit the behavior of an optomechanicalor photomechanical transducer. The transducer responds to light in a quick and reversible manner converting a time-variable light source into a time-variable mechanical stress easily monitored by a device such as a strain gage.

Fedors, R. F.↗
NASA NTRS1980

An equation of state for liquids

Closed expression for volume as function of pressure and temperature has been verified for over 250 liquids. Equation can assist chemical engineers, soild-state researchers, and others with interest in thermodynamic behavior of liquids.

Fedors, R. F.↗
NASA NTRS1980

Relating viscosity to polymer concentration

Equation developed by VanDijk and first applied to viscosity of Newtonian suspension of rigid particles by Eilers is rearranged to yield intrinsic viscosity as explicit function of polymer concentration in polymer solvent system. Experiments have shown relationship valid for polymer solutions having relative viscosities ranging from 1 to 100.

Fedors, R. F.↗
NASA NTRS1980

Simple estimate of critical volume

Method for estimating critical molar volume of materials is faster and simpler than previous procedures. Formula sums no more than 18 different contributions from components of chemical structure of material, and is as accurate (within 3 percent) as older more complicated models. Method should expedite many thermodynamic design calculations.

Fedors, R. F.↗
NASA NTRS1980

Equilibrium swelling of elastomers in solvents

Two proposed empirical equations, developed from Eilers-VanDijk equation to characterize relative modulus of filled elastomers as function of filler content, describe: (1) equilibrium swelling for cases where fillers are composed of permanent aggregates of primary particles; and (2) equilibrium swelling when filler material is composed of non-aggregated particles.

Fedors, R. F.↗
NASA NTRS1979

"Self-packaging" desiccant

Desiccant, consisting of water-soluble filler contained in water-permeable elastomeric matrix, absorbs large quantities of water without becoming sticky or releasing corrosive agents. Desiccant may be molded into virtually any shape depending on area of application.

Fedors, R. F.↗
NASA NTRS1979

Compatibility of elastomers in alternate jet fuels

The compatibility of elastomeric compositions of known resistance to aircraft fuels was tested for potential use in Jet A type fuels obtainable from alternate sources, such as coal. Since such fuels were not available at the time, synthetic alternate fuels were prepared by adding tetralin to a petroleum based Jet A type fuel to simulate coal derived fuels which are expected to contain higher amounts of aromatic and hydroaromatic hydrocarbons. The elastomeric compounds tested were based on butadiene-acrylonitrile rubber, a castable Thiokol polysulfide rubber, and a castable fluorosilicone rubber. Batches of various cross-link densities of these rubbers were made and their chemical stress relaxation behavior in fuel, air, and nitrogen, their swelling properties, and response to mechanical testing were determined.

Kalfayan, S. H.↗
NASA NTRS1979

Ultrathin films as photomechanical transducer

Stretched ultrathin, metallized polyimide film is used as photochemical transducer for detection and measurement of total exposure to light. Film is potential nonelectrical replacement for solar cells.

Fedors, R. F.↗
NASA NTRS1979

A relationship between maximum packing of particles and particle size

Experimental data indicate that the volume fraction of particles in a packed bed (i.e. maximum packing) depends on particle size. One explanation for this is based on the idea that particle adhesion is the primary factor. In this paper, however, it is shown that entrainment and immobilization of liquid by the particles can also account for the facts.

Fedors, R. F.↗
NASA NTRS1979

A method to estimate critical volumes

Methods for estimating the volume of the critical temperature used for the estimation of thermodynamic properties of substances are described. The possibility to estimate the critical temperature by using a combination of only eighteen atomic and structural contributions is shown. These contributions are listed and the critical temperature is given by a linear expression. By comparing the Vetere (1976) and Lydersen (1955) methods with the method discussed it is noted that while all three methods yield about the same average error (about 3%), the new method is superior in that it requires a smaller number of increments to fit data points.

Fedors, R. F.↗
NASA NTRS1979

A universal reduced glass transition temperature for liquids

Data on the dependence of the glass transition temperature on the molecular structure for low-molecular-weight liquids are analyzed in order to determine whether Boyer's reduced glass transition temperature (1952) is a universal constant as proposed. It is shown that the Boyer ratio varies widely depending on the chemical nature of the molecule. It is pointed out that a characteristic temperature ratio, defined by the ratio of the sum of the melting temperature and the boiling temperature to the sum of the glass transition temperature and the boiling temperature, is a universal constant independent of the molecular structure of the liquid. The average value of the ratio obtained from data for 65 liquids is 1.15.

Fedors, R. F.↗
NASA NTRS1979

Ultrathin films as photomechanical transducers

In order to investigate the photomechanical effect in ultrathin films, several commercially available polymers of various structure and properties have been studied experimentally below the glass transition temperature. In the experiments using an Instron test machine equipped with a 200-g load cell and a microscope stage illuminator as the light source, the load at the fixed strain was recorded as a function of time. Plots of the steady-state change in stress as a function of the intensity of the incident radiation are presented for several of the materials studied. The response is found to be linear; the greater the intensity of the incident radiation, the greater is the change in stress.

Sarbolouki, M. N.↗
NASA NTRS1977

Determining critical temperatures and volumes

Technique estimates critical temperature and volume of fluid from chemical composition and structure without additional empirical data. Method can help designers interested in materials for which critical constants are unavailable.

Fedors, R. F.↗
NASA NTRS1977

Determining viscosities of liquids

Method requires only chemical composition and molecular structure to evaluate viscosity for many liquids. Accuracies of fifteen percent or better are obtained without experimentation.

Fedors, R. F.↗
NASA NTRS1977

Reduced variable technique for predicting grain behavior

The use of reduced variables to account for the time-temperature dependence of the relaxation modulus is a standard and universally adopted technique in the stress analysis of solid propellant grains. Recent work has suggested that the reduced variable technique can also be used to account for the dependence of the relaxation modulus on the crosslink density of an elastomer system. By combining variables, it is now possible to determine the relaxation modulus as a function of both mechanical and chemical parameters over a long period of time. The problems involved, the pitfalls to be avoided, and suggested techniques to be used in acquiring data are discussed.

Lewis, G. W.↗