Engineering Papers⌕ Search

Engineering topics

Farmer, Jeffery T.

Publications and source records attributed to Farmer, Jeffery T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Extended Stroke and Miniaturized Reverse-Operation DTE Thermal Switches

This paper describes two advanced thermal switches under development that are offshoots of the recently flight-qualified 2500:1 reverse-operation differential thermal expansion (DTE) thermal switch (ROD-TSW). The first is the extended stroke ROD-TSW (ES-ROD-TSW) while the second is the miniaturized ROD-TSW (mini-ROD-TSW). Each employs multiple diametrically nested DTE stages in contrast to the single-stage ROD-TSW. The ES-ROD-TSW employs two stages and a negative CTE material known as Allvar and its main purpose is to extend its stroke for use in non-vacuum planetary environments. The mini-ROD-TSW employs four stages to miniaturize its size for use in compact lunar instruments and rovers. The ES-ROD-TSW was TVAC tested at JPL and its ON/OFF ratio is 13000:1 based on a measured ON conductance of 6.89 W/K and a calculated OFF conductance of 0.00053 W/K. The mini-ROD-TSW is targeted to have an ON conductance of 1.5 W/K and an OFF conductance of 0.0015 W/K, both verified by analysis. Test verification of the mini-ROD-TSW remains to be carried out. The paper will provide design/performance details of each device.

Farmer, Jeffery T.↗
NASA NTRS2018

Copper-Water and Hybrid Aluminum-Ammonia Heat Pipes for Spacecraft Thermal Control Applications

Copper-water heat pipes are commonly used for thermal management of electronics systems on earth and aircraft, but have not been used in spacecraft thermal control applications to date, due to the satellite industry's requirement that any device or system be successfully tested in a microgravity environment prior to adoption. Recently, Advanced Cooling Technologies Inc., (ACT), NASA Marshall Space Flight Center, and the International Space Station office at NASA's Johnson Space Center demonstrated flight heritage in Low-Earth Orbit. The testing was conducted aboard the International Space Station (ISS) under the Advanced Passive Thermal eXperiment (APTx) project. The heat pipes were embedded in a high conductivity (HiK"TM") aluminum base plate and subject to a variety of thermal tests over a temperature range of -10 to 38 ºC for a ten-day period. Results showed excellent agreement with both predictions and ground tests. In addition, novel hybrid wick aluminum-ammonia heat pipes are developed to handle heat flux requirements for spacecraft thermal control applications. The 5-10 W/cm2 heat density limitation of aluminum-ammonia grooved heat pipes has been a fundamental limitation in the current design for space applications. The recently demonstrated 50 W/cm2 capability of the hybrid high heat flux heat pipes provides a realistic means of managing the high heat density anticipated for the next generation space designs.

Ababneh, Mohammed T.↗
NASA NTRS2016

Hybrid Heat Pipes for Lunar and Martian Surface and High Heat Flux Space Applications

Novel hybrid wick heat pipes are developed to operate against gravity on planetary surfaces, operate in space carrying power over long distances and act as thermosyphons on the planetary surface for Lunar and Martian landers and rovers. These hybrid heat pipes will be capable of operating at the higher heat flux requirements expected in NASA's future spacecraft and on the next generation of polar rovers and equatorial landers. In addition, the sintered evaporator wicks mitigate the start-up problems in vertical gravity aided heat pipes because of large number of nucleation sites in wicks which will allow easy boiling initiation. ACT, NASA Marshall Space Flight Center, and NASA Johnson Space Center, are working together on the Advanced Passive Thermal experiment (APTx) to test and validate the operation of a hybrid wick VCHP with warm reservoir and HiK"TM" plates in microgravity environment on the ISS.

Ababneh, Mohammed T.↗
NASA NTRS2013

Development and Testing of a Variable Conductance Thermal Acquisition, Transport, and Switching System

This paper describes the development and testing of a scalable thermal management architecture for instruments, subsystems, or systems that must operate in severe space environments with wide variations in sink temperature. The architecture involves a serial linkage of one or more hot-side variable conductance heat pipes (VCHPs) to one or more cold-side loop heat pipes (LHPs). The VCHPs provide wide area heat acquisition, limited distance thermal transport, modest against gravity pumping, concentrated LHP startup heating, and high switching ratio variable conductance operation. The LHPs provide localized heat acquisition, long distance thermal transport, significant against gravity pumping, and high switching ratio variable conductance operation. The single-VCHP, single-LHP system described herein was developed to maintain thermal control of a small robotic lunar lander throughout the lunar day-night thermal cycle. It is also applicable to other variable heat rejection space missions in severe environments. Operationally, despite a 60-70% gas blocked VCHP condenser during ON testing, the system was still able to provide 2-4 W/K ON conductance, 0.01 W/K OFF conductance, and an end-to-end switching ratio of 200-400. The paper provides a detailed analysis of VCHP condenser performance, which quantified the gas blockage situation. Future multi-VCHP/multi-LHP thermal management system concepts that provide power/transport length scalability are also discussed.

Bugby, David C.↗
NASA NTRS2010

Two-Phase Thermal Switching System for a Small, Extended Duration Lunar Surface Science Platform

This paper describes a novel thermal control system for the Warm Electronics Box (WEB) on board a small lunar surface lander intended to support science activities anywhere on the lunar surface for an extended duration of up to 6 years. Virtually all lander electronics, which collectively dissipate about 60 W in the reference mission, are contained within the WEB. These devices must be maintained below 323 K (with a goal of 303 K) during the nearly 15-earth-day lunar day, when surface temperatures can reach 390K, and above 263 K during the nearly 15-earth-day lunar night, when surface temperatures can reach 100K. Because of the large temperature swing from lunar day-to-night, a novel thermal switching system was required that would be able to provide high conductance from WEB to radiator(s) during the hot lunar day and low (or negligible) conductance during the cold lunar night. The concept that was developed consists of ammonia variable conductance heat pipes (VCHPs) to collect heat from WEB components and a polymer wick propylene loop heat pipe (LHP) to transport the collected heat to the radiator(s). The VCHPs autonomously maximize transport when the WEB is warm and autonomously shut down when the WEB gets cold. The LHP autonomously shuts down when the VCHPs shut down. When the environment transitions from lunar night to day, the VCHPs and LHP autonomously turn back on. Out of 26 analyzed systems, this novel arrangement was able to best achieve the combined goals of zero control power, autonomous operation, long life, low complexity, low T, and landed tilt tolerance.

Bugby, David C.↗
NASA NTRS2007

Prospecting Rovers for Lunar Exploration

A study of lunar rover options for exploring the permanently shadowed regions of the lunar environment is presented. The potential for nearly continuous solar illumination coupled with the potential for water ice, focus exploration planner's attention on the polar regions of the moon. These regions feature craters that scientists have reason to believe may contain water ice. Water ice can be easily converted to fuel cell reactants, breathing oxygen, potable water, and rocket propellant. For these reasons, the NASA Robotic Lunar Exploration Program (RLEP) sponsored a study of potential prospecting rover concepts as one part of the RLEP-2 Pre-Phase A. Numerous vehicle configurations and power, thermal, and communication options are investigated. Rover options in the 400kg to 530kg class are developed which are capable of either confirming the presence of water ice at the poles, or conclusively demonstrating its absence.

Graham, Jerry B.↗
NASA NTRS2000

Two Fiber Optical Fiber Thermometry

An optical fiber thermometer consists of an optical fiber whose sensing tip is given a metallic coating. The sensing tip of the fiber is essentially an isothermal cavity, so the emission from this cavity will be approximately equal to the emission from a blackbody. Temperature readings are obtained by measuring the spectral radiative heat flux at the end of the fiber at two wavelengths. The ratio of these measurements and Planck's Law are used to infer the temperature at the sensing tip. Optical fiber thermometers have high accuracy, excellent long-term stability and are immune to electromagnetic interference. In addition, they can be operated for extended periods without requiring re-calibration. For these reasons. it is desirable to use optical fiber thermometers in environments such as the International Space Station. However, it has recently been shown that temperature readings are corrupted by emission from the fiber when extended portions of the probe are exposed to elevated temperatures. This paper will describe several ways in which the reading from a second fiber can be used to correct the corrupted temperature measurements. The accuracy and sensitivity to measurement uncertainty will be presented for each method.

Jones, Mathew R.↗
NASA NTRS1992

Conceptual design of a lunar base thermal control system

Space station and alternate thermal control technologies were evaluated for lunar base applications. The space station technologies consisted of single-phase, pumped water loops for sensible and latent heat removal from the cabin internal environment and two-phase ammonia loops for the transportation and rejection of these heat loads to the external environment. Alternate technologies were identified for those areas where space station technologies proved to be incompatible with the lunar environment. Areas were also identified where lunar resources could enhance the thermal control system. The internal acquisition subsystem essentially remained the same, while modifications were needed for the transport and rejection subsystems because of the extreme temperature variations on the lunar surface. The alternate technologies examined to accommodate the high daytime temperatures incorporated lunar surface insulating blankets, heat pump system, shading, and lunar soil. Other heat management techniques, such as louvers, were examined to prevent the radiators from freezing. The impact of the geographic location of the lunar base and the orientation of the radiators was also examined. A baseline design was generated that included weight, power, and volume estimates.

Simonsen, Lisa C.↗
NASA NTRS1991

Geostationary orbit Earth science platform concepts for global change monitoring

Functionality of a geostationary spacecraft to support Earth science regional process research is identified. Most regional process studies require high spatial and temporal resolution. These high temporal resolutions are on the order of 30 minutes and may be achievable with instruments positioned in a geostationary orbit. A complement of typical existing or near term instruments are identified to take advantage of this altitude. This set of instruments is listed, and the requirements these instruments impose on a spacecraft are discussed. A brief description of the geostationary spacecraft concepts which support these instruments is presented.

Farmer, Jeffery T.↗
NASA NTRS1991

On-orbit structural dynamic performance of a low-frequency microwave radiometer for Mission to Planet Earth applications

The present paper addresses the on-orbit dynamic performance of a low-frequency microwave radiometer for earth science applications. The radiometer is one of the earth-observing instruments aboard a geostationary platform proposed as part of the Mission to Planet Earth. The paper includes establishing the structural requirements of the antenna, developing the structural and disturbance models, performing modal and forced response analyses, and evaluating the resulting distortions in terms of the antenna's ability to meet stringent structural performance requirements. Two antenna configurations are discussed: free-flying and platform-mounted. These configurations are analyzed for a representative disturbance function which simulates rotation of the subreflector in order to perform a raster-type scan of the earth disk. Results show that the scanning maneuver modeled did not induce antenna performance errors which were outside their estimated limits.

Wahls, Deborah M.↗
NASA NTRS1990

On-orbit structural dynamic performance of a 15-meter microwave radiometer antenna

The on-orbit structural dynamic performance of a microwave radiometer antenna for Earth science applications is addressed. The radiometer is one of the Earth-observing instruments aboard a proposed geostationary platform as part of the Mission to the Planet Earth. A sequential approach is presented for assessing the ability of an antenna structure to retain its geometric shape subject to a representative onboard disturbance. This approach includes establishing the structural requirements of the antenna, developing the structural and disturbance models, performing modal and forced response analyses, and evaluating the resulting distortions in terms of the antenna's ability to meet stringent structural performance requirements. Two antenna configurations are discussed: free-flying and platform-mounted. These configurations are analyzed for a representative disturbance function which simulates rotation of the subreflector in order to perform a raster-type scan of the Earth disk. Results show that the scanning maneuver modeled would not induce antenna structural errors outside the specified limits.

Wahls, Deborah M.↗
NASA NTRS1990

Thermal-distortion analysis of a spacecraft box truss in geostationary orbit

The Mission to Planet Earth enlists the use of a geostationary platform to support Earth science monitoring instruments. The strongback for a proposed geostationary platform is a deployable box truss that supports two large diameter passive microwave radiometer (PMR) and several other science instruments. A study was performed to estimate the north-south and east-west pointing errors at the mounting locations of the two PMRs due to on-orbit thermal distortions of the main truss. The baseline configuration indicated that the east-west pointing error greatly exceeded the required limits. Primary origins of the pointing errors were identified, and methods for their reduction were discussed. Thermal performance enhancements to the truss structure were modeled and analyzed, including state-of-the-art surface coatings and insulation techniques. Comparisons of the thermal enhancements to the baseline were performed. Results demonstrated that using a thermal enclosure insulating technique reduced external heat fluxes, and distributed those heat fluxes more evenly throughout the structure, sufficiently reducing the pointing error to satisfy pointing accuracy requirements for the PMR's.

Cosgrove, Patrick A.↗
NASA NTRS1990

Thermal analysis of a strongback structure for a high-frequency microwave antenna concept in geosynchronous orbit

The effects of the geosynchronous thermal environment on the performance of a tetrahedral truss strongback structure for a high-frequency microwave antenna concept for earth science monitoring have been studied. Two orbit conditions (an equinox orbit with a 72-minute eclipse and a solstice orbit with no eclipse) and a range of thermal control approaches were investigated under steady state and transient conditions. The thermal control approaches included aluminum surface coatings with high and low solar-absorptivity-to-infrared-emissivity ratios, multi-layer insulation, a sun shield, and various truss element materials. The effects of both earth shadowing and shadowing by the antenna reflector on temperatures were also examined. Temperatures and corresponding structural distortion results are presented.

Farmer, Jeffery T.↗
NASA NTRS1989

Conceptual design of a communications system for Mars exploration missions

Future missions to Mars will require a communications system to link activities on the Martian surface with each other and with mission controllers on earth. This paper documents the preliminary design of an areosynchronous communications satellite to provide such links. As designed, the satellite will provide almost continuous communication between Mars and earth, as well as continuous Mars surface-to-surface links. The capacity will exist for voice, data/command, and video transmission. The mission scenario assumed for this design is described, followed by the configuration design. The communications systems conceptual design and its impact on the overall spacecraft requirements are then presented. Supporting subsystems including electrical power; thermal control; guidance, navigation, and control; propulsion; structures; and configuration are reviewed. A description of the operating orbit and the assumed method of orbit acquisition are discussed.

Badi, Deborah M.↗
NASA NTRS1988

Overview of SDCM - The Spacecraft Design and Cost Model

The Spacecraft Design and Cost Model (SDCM) is a computer-aided design and analysis tool for synthesizing spacecraft configurations, integrating their subsystems, and generating information concerning on-orbit servicing and costs. SDCM uses a bottom-up method in which the cost and performance parameters for subsystem components are first calculated; the model then sums the contributions from individual components in order to obtain an estimate of sizes and costs for each candidate configuration within a selected spacecraft system. An optimum spacraft configuration can then be selected.

Ferebee, Melvin J.↗