Engineering topics

Fang, Xiaotian

Publications and source records attributed to Fang, Xiaotian.

5 records

DOE OSTI2024

Exploring the relationship between deposition method, microstructure, and performance of Nb/Si-based superconducting coplanar waveguide resonators

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. Here, in this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Influence of intermediate carbon content on the microstructure and high-temperature mechanical properties of cast and wrought Ni-based superalloy nimonic 105

NIMONIC® 105 variants with three different carbon concentrations were manufactured. Here, the medium carbon content variant shows inferior creep properties due to a bimodal grain size distribution and non-uniform carbides repartition leading to plastic strain accumulation between the two domains. Here, this eventually facilitated facile cracking and void formation during high-temperature creep.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Microstructure and Mechanical Properties of Ni-Based Superalloy Nimonic 105 with Varying Carbon Content

High carbon levels have been found to improve the fabricability of high-strength cast and wrought Ni-based superalloys, enabling the development of superior cast/wrought materials. However, carbon also strongly influences the microstructure and mechanical properties of the alloys. Nimonic 105 variants with three different carbon concentrations were manufactured. A bimodal grain size was found in the intermediate carbon content variant, while the high (low) carbon resulted in fine (coarse) grains thereby significantly affecting creep performance. The variations in grain structure were attributed to the primary carbides. An intermediate carbon level showed the best combination of strength and ductility in tension at high-temperature but little improvement in, or even inferior, creep performance. Discussion of the results will establish an understanding of the influence of carbon on the microstructure and mechanical properties of high strength cast and wrought superalloys, providing insights into obtaining high-quality alloys for future high-temperature applications.

Fang, Xiaotian↗

DOE OSTI2024

Microstructure and Chemical Composition of Al2O3-, Cr2O3- and MgO-rich Refractories Exposed to Plastic Ashes

Plastics are widely integrated with today’s lifestyle due to their low cost, durability, lightweight, water resistance, and flexibility. However, tremendous plastic waste cause severe threats to the environment. Thus, sustainable recycling of plastic waste is critical, where plastic waste gasification technology with carbon management becomes one of the most effective recycling methods. We simulate the gasification process by exposing the Al2O3-, Cr2O3- and MgO-rich refractories to synthetic plastic ashes at 1500 ℃ for 50 h. A comprehensive study on the microstructure and chemical composition change before/after exposure is conducted using scanning electron microscopy. Meanwhile, the differences among these three refractories after exposure are revealed for quantifying the performance in plastic ashes. Discussion of the results will establish an understanding of the influence of plastic ashes on the microstructure, composition, and phase of different types of refractories, providing insights into designing new refractory materials for future recycling of plastic waste.

Fang, Xiaotian↗

DOE OSTI2023

Revealing Possible Coherence Limiting Sources in Superconducting Qubit with Advanced Electron Microscopy

Superconducting materials hold great potential for solid-state quantum computing. Their fabrication relies on established semiconductor fabrication techniques, such as thin film deposition and lithography, but the complex processing steps can result in defects at the qubits' interfaces and surfaces that can negatively impact coherence time. To improve superconducting qubit performance, it is essential to understand the structural features, at the atomic scale, that may act as sources of decoherence limiting factor in both the Josephson junction (JJ) and resonators, which are key components of superconducting qubit. This talk will present our recent studies on the microstructures in a 2D-transmon, with an emphasis on the JJ. For this research, a combination of advanced microscopy techniques, including high-resolution (S)TEM imaging, and spectroscopy (EDS and EELS) are used to identify possible coherence-limiting defects or structural features.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗