Engineering Papers⌕ Search

Engineering topics

Falarski, M. D.

Publications and source records attributed to Falarski, M. D..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Wind tunnel investigation of a large-scale 25 deg swept-wing jet transport model with an external blowing triple-slotted flap

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally blown triple-slotted flap. The lift of the model was augmented by the turbofan engine exhaust impingement on the flap surface. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The model was tested with two flap extents. One extended from 0.11 to 1.00 of the wing semispan, and the other extended from 0.11 to 0.75 of the wing semispan with a single-slotted aileron from 0.75 to 1.00 of the wing semispan. The results were obtained for several flap deflections with and without the horizontal tail at gross thrust coefficients from 0 to 4.0. Longitudinal and lateral data are presented with three and four engines operating.

Aoyagi, K.↗
NASA NTRS1973

Aerodynamic characteristics of a large-scale model with a swept wing and a jet flap having an expandable duct

The data from an investigation of the aerodynamic characteristics of the expandable duct-jet flap concept are presented. The investigation was made using a large-scale model in the Ames 40- by 80-foot Wind Tunnel. The expandable duct-jet flap concept uses a lower surface, split flap and an upper surface, Fowler flap to form an internal, variable area cavity for the blowing air. Small amounts of blowing are used on the knee of the upper surface flap and the knee of a short-chord, trailing edge control flap. The bulk of the blowing is at the trailing edge. The flap could extend the full span of the model wing or over the inboard part only, with blown ailerons outboard. Primary configurations tested were two flap angles, typical of takeoff and landing; symmetric control flap deflections, primarily for improved landing performance; and asymmetric aileron and control flap deflections, for lateral control.

Aiken, T. N.↗
NASA NTRS1973

Acoustic characteristics of a large-scale wind tunnel model of an upper-surface blown flap transport having two engines

The upper-surface blown (USB) flap as a powered-lift concept has evolved because of the potential acoustic shielding provided when turbofan engines are installed on a wing upper surface. The results from a wind tunnel investigation of a large-scale USB model powered by two JT15D-1 turbofan engines are-presented. The effects of coanda flap extent and deflection, forward speed, and exhaust nozzle configuration were investigated. To determine the wing shielding the acoustics of a single engine nacelle removed from the model were also measured. Effective shielding occurred in the aft underwing quadrant. In the forward quadrant the shielding of the high frequency noise was counteracted by an increase in the lower frequency wing-exhaust interaction noise. The fuselage provided shielding of the opposite engine noise such that the difference between single and double engine operation was 1.5 PNdB under the wing. The effects of coanda flap deflection and extent, angle of attack, and forward speed were small. Forward speed reduced the perceived noise level (PNL) by reducing the wing-exhaust interaction noise.

Falarski, M. D.↗
NASA NTRS1973

Wind tunnel investigation of a large-scale upper surface blown-flap transport model having two engines

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blowing flap system that would augment lift. The model had a 25 deg swept wing of aspect ratio 7.89 and two turbofan engines with the engine centerline located at 0.256 of the wing semispan. The lift of the flap system was augmented by turbofan exhaust impingement on the Coanda surface. Results were obtained for several flap deflections and engine nozzle configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with two engines operating. Limited longitudinal and lateral data are presented with an engine out. In addition, limited exhaust and flap pressure data are presented.

Aoyagi, K.↗
NASA NTRS1973

Acoustic characteristics of a semispan wing equipped with an externally blown jet flap including results at forward speed

A wind-tunnel investigation was made of the noise characteristics of a 14.5-ft semispan, externally blown jet flap model. The model was equipped with a single 30-in. diameter, ducted fan with a 1.03 pressure ratio. The effects of flap size, fan vertical location, and forward speed on the noise characteristics were studied. With the ducted fan mounted 0.79 or 1.24 diameters below the wing and a flap chord greater than 50 percent, the peak perceived noise level increased 2 to 3 Pndb when the flap was deflected to 90 deg. The jet scrubbing noise increase 3 to 4 db when the flap was deflected 90 deg. Installation of the fan on the wing was responsible for 1 to 2 db of this change. Forward speed did not have a significant effect on the perceived noise level, although it did cause a reduction in the sound pressure levels of the first and second fan harmonics.

Falarski, M. D.↗
NASA NTRS1973

Aspects of investigating STOL noise using large-scale wind-tunnel models.

The applicability of the NASA Ames 40- by 80-foot wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind-tunnel test section have been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied in both the free-field and wind-tunnel acoustic environments. The results of these studies indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. A directional microphone, a phased array of microphones, and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be distinguishible from the wind-tunnel background noise.

Falarski, M. D.↗
NASA NTRS1972

Longitudinal aerodynamic characteristics of a large scale model with a swept wing and augmented jet flap in ground effect

The investigation of the in-ground-effect, longitudinal aerodynamic characteristics of a large scale swept augmentor wing model is presented, using 40 x 80 ft wind tunnel. The investigation was conducted at three ground heights; h/c equals 2.01, 1.61, and 1.34. The induced effect of underwing nacelles, was studied with two powered nacelle configurations. One configuration used four JT-15D turbofans while the other used two J-85 turbojet engines. Two conical nozzles on each J-85 were used to deflect the thrust at angles from 0 to 120 deg. Tests were also performed without nacelles to allow comparison with previous data from ground effect.

Falarski, M. D.↗
NASA NTRS1972

Aerodynamic characteristics of a swept augmentor wing

A brief outline of augmentor wing research is presented and is followed by a discussion of large scale wind tunnel test results for a swept augmentor wing configuration. The results show that the augmentor wing can be applied to high speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.

Koenig, D. G.↗
NASA NTRS1972

Acoustic characteristics of large-scale STOL model at forward speed

Wind-tunnel investigations of the acoustic characteristics of the externally blown jet flap (EBF) and augmentor wing STOL concepts are dicussed. The large-scale EBF model was equipped with a triple-slotted blown by four JT15D turbofan engines with circular, coannular exhaust nozzles. The large-scale augmentor wing model was equipped with an unlined augmentor blown by a slot primary nozzle. The effects of airspeed and angle of attack on the acoustics of the EBF were small. At a forward speed of 60 knots, the impingement noise of the landing flap was approximately 2 db lower than in the static tests. Angle of attack increased the impingement noise approximately 0.1 decibels per degree. Flap deflection had a greater effect on the acoustics of the augmentor wing than did airspeed. For a nozzle pressure ratio of 1.9, the peak perceived noise level of the landing flap was 3 to 5 PNdb higher than that of the takeoff flap. The total sound power was also significantly higher for landing indicating that turning in the augmentor generated acoustic energy. Airspeed produced a small aft shift in acoustic directivity with no significant change in the peak perceived noise levels or sound power levels.

Falarski, M. D.↗
NASA NTRS1972

Wind tunnel investigation of a large scale 35 deg swept wing jet transport model with an external blowing triple slotted flap

An investigation was conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally jet-augmented flap system that would augment lift and provide direct-lift control. The model had a 35 deg swept wing of aspect ratio 7.82 and two side-by-side engines mounted on a single pylon under each wing close to the fuselage. The lift of the flap system was augmented by jet engine exhaust impingement on the triple-slotted flap surfaces. The rearmost flap provided direct lift control. Results were obtained for several combinations of flap deflections at gross thrust coefficients from 0 to 2.0. Three-component longitudinal data are presented with four engines operating. Limited longitudinal and lateral data are presented for asymmetric and symmetric thrust conditions with three engines operating. For the same overall flap deflection, lift coefficient and maximum lift coefficient were improved 13 and 7 percent compared to coefficients obtained with a double-slotted flap configuration. A maximum lift coefficient of 6.3 was obtained at a gross thrust coefficient of 2.0. At the same flap deflection lateral and directional trim moment requirements with an engine inoperative were reduced 55 and 33 percent, respectively, compared to those with the engines located farther outboard on the wing. Trim moment requirements in pitch were also reduced significantly. However, pitching-moment instability occurred and increased with gross thrust coefficient.

Aoyagi, K.↗
NASA NTRS1972

Aspects of investigating STOL noise using large scale wind tunnel models

The applicability of the NASA Ames 40- by 80-ft wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind tunnel test section has been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied both in the free-field and wind tunnel acoustic environments. The results indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. Directional microphone and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be discernable from the wind tunnel background noise.

Falarski, M. D.↗
NASA NTRS1972

Large-scale wind-tunnel investigation of the noise characteristics of a semispan wing equipped with an externally blown jet flap

A wind tunnel investigation was made of the noise characteristics of a 4.42 m(14.5 foot) semispan, externally-blown jet flap model. The model was equipped with a single 76.2 cm(30 inch) diameter, ducted fan with a 1.03 pressure ratio. The effects of flap size, fan vertical location, and forward speed on the noise characteristics were studied. The data from the investigation is presented in the form of tabulated one-third octave band frequency spectrums and perceived noise levels for each test condition.

Falarski, M. D.↗
NASA NTRS1972

Aerodynamic characteristics of a swept augmentor wing

A brief outline of augmentor wing research sponsored by Ames Research Center is presented and is followed by a discussion of large-scale wind-tunnel test results for a swept augmentor wing configuration. The results showed that the augmentor wing could be applied to high-speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.

Koenig, D. G.↗
NASA NTRS1972

Acoustic characteristics of large-scale STOL models at forward speed

Wind-tunnel investigations of the acoustic characteristics of the externally blown jet flap (EBF) and augmentor wing STOL concepts are discussed. The large-scale EBF model was equipped with a triple-slotted flap blown by four JT15D turbofan engines with circular, coannular exhaust nozzles. The large-scale augmentor wing model was equipped with an unlined augmentor blown by a slot primary nozzle. The effects of airspeed and angle of attack on the acoustics of the EBF were small. Flap deflection had a greater effect on the acoustics of the augmentor wing than did airspeed. The total sound power was also significantly higher for landing indicating that turning in the augmentor generated acoustic energy. Airspeed produced a small aft shift in acoustic directivity with no significant change in the peak perceived noise levels or sound power levels. Small-scale research of the acoustics for the augmentor wing has shown that by blowing an acoustically treated augmentor with a lobed primary nozzle, the 95-PNdb noise level goal can be achieved or surpassed.

Falarski, M. D.↗
NASA NTRS1971

Aerodynamic characteristics of a large scale model with a swept wing and augmented jet flap

Data of tests of a large-scale swept augmentor wing model in the 40- by 80-foot wind tunnel are presented. The data includes longitudinal characteristics with and without a horizontal tail as well as results of preliminary investigation of lateral-directional characteristics. The augmentor flap deflection was varied from 0 deg to 70.6 deg at isentropic jet thrust coefficients of 0 to 1.47. The tests were made at a Reynolds number from 2.43 to 4.1 times one million.

Falarski, M. D.↗