Engineering Papers⌕ Search

Engineering topics

Etsion, I.

Publications and source records attributed to Etsion, I..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Improved gas thrust bearings

Two variations of gas-lubricated thrust bearings extend substantially load-carrying range over existing gas bearings. Dual-Action Gas Thrust Bearing's load-carrying capacity is more than ninety percent greater than that of single-action bearing over range of compressibility numbers. Advantages of Cantilever-mounted Thrust Bearing are greater tolerance to dirt ingestion, good initial lift-off characteristics, and operational capability over wide temperature range.

Anderson, W. J.↗
NASA NTRS1978

Hydrodynamic effects in a misaligned radial face seal

Hydrodynamic effects in a flat seal having an angular misalignment are analyzed, taking into account the radial variation in seal clearance. An analytical solution for axial force, restoring moment, and transverse moment is presented that covers the whole range from zero to full angular misalignment. Both low pressure seals with cavitating flow and high pressure seals with full fluid film are considered. Strong coupling is demonstrated between angular misalignment and transverse moment which leads the misalignment vector by 90 degrees. This transverse moment, which is entirely due to hydrodynamic effects, may be a significant factor in seal operating mechanism.

Etsion, I.↗
NASA NTRS1978

Radial forces in a misaligned radial face seal

Radial forces on the primary seal ring of a flat misaligned seal are analyzed, taking into account the radial variation in seal clearance. An analytical solution for both hydrostatic and hydrodynamic effects is presented that covers the whole range from zero to full angular misalignment. The net radial force on the primary seal ring is always directed so as to produce a radial eccentricity which generates inward pumping. Although the radial force is usually very small, in some cases it may be one of the reasons for excessive leakage through both the primary and secondary seals of a radial face seal.

Etsion, I.↗
NASA NTRS1978

The accuracy of the narrow seal approximation in analyzing radial face seals

The accuracy of the narrow seal approximation which enables closed form analytical solutions for radial face seals is examined in this paper. Both hydrostatic and hydrodynamic effects in a flat, misaligned seal are considered. Analytical results obtained from a simplified Reynolds equation, based on the neglect of circumferential pressure gradient and seal curvature, are compared with accurate results from numerical solution of the complete Reynolds equation. The agreement between the approximate and accurate solutions is quite reasonable over a wide range of a seal's inner-to-outer radius ratio. For radius ratios greater than 0.8, the accuracy of the narrow seal approximation is better than 1 percent over most of the range of angular misalignment.

Etsion, I.↗
NASA NTRS1978

Cantilever mounted resilient pad gas bearing

A gas-lubricated bearing is described, employing at least one pad mounted on a rectangular cantilever beam to produce a lubricating wedge between the face of the pad and a moving surface. The load-carrying and stiffness characteristics of the pad are related to the dimensions and modulus of elasticity of the beam. The bearing is applicable to a wide variety of types of hydrodynamic bearings.

Etsion, I.↗
NASA NTRS1977

Radial forces in a misaligned radial face seal

Radial forces on the primary seal ring of a flat misaligned seal are analyzed, taking into account the radial variation in seal clearance. An analytical solution for both hydrostatic and hydrodynamic effects is presented that covers the whole range from zero to full angular misalignment. The net radial force on the primary seal ring is always directed so as to produce a radial eccentricity which generates inward pumping. Although the radial force is usually very small, in some cases it may be one of the reasons for excessive leakage through both the primary and secondary seals of a radial face seal.

Etsion, I.↗
NASA NTRS1977

Design charts for arbitrarily pivoted, liquid-lubricated flat-sector-pad thrust bearing

A flat, sector-shaped geometry for a liquid-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. Results are presented in design charts that enable a direct approach to the design of point- and line-pivoted, tilting pad bearings. A comparison is made with the Mitchell bearing approximation and it is found that this approximation always overestimates load capacity.

Etsion, I.↗
NASA NTRS1977

Hydrodynamic effects in a misaligned radial face seal

Hydrodynamic effects in a flat seal having an angular misalignment are analyzed, taking into account the radial variation in seal clearance. An analytical solution for axial force, restoring moment, and transverse moment is presented that covers the whole range from zero to full angular misalignment. Both low pressure seals with cavitating flow and high pressure seals with full fluid film are considered. Strong coupling is demonstrated between angular misalignment and transverse moment which leads the misalignment vector by 90 degrees. This transverse moment, which is entirely due to hydrodynamic effects, is a significant factor in the seal operating mechanism.

Etsion, I.↗
NASA NTRS1977

Computer program for flat sector thrust bearing performance

A versatile computer program is presented which achieves a rapid, numerical solution of the Reynolds equation for a flat sector thrust pad bearing with either compressible or liquid lubricants. Program input includes a range in values of the geometric and operating parameters of the sector bearing. Performance characteristics are obtained from the calculated bearing pressure distribution. These are the load capacity, center of pressure coordinates, frictional energy dissipation, and flow rates of liquid lubricant across the bearing edges. Two sample problems are described.

Presler, A. F.↗
NASA NTRS1977

Optimum step design for centering of pistons moving in an incompressible fluid

Hydrodynamic effects are analyzed for a stepped piston moving within a tight clearance tube filled with an incompressible fluid. Together with the hydrostatic effects that were analyzed in an earlier paper, a complete solution is obtained and an optimum step design for centering of the piston is suggested. The axial speed resulting from an axial driving force is calculated, and some experimental results for pistons falling in a water filled tube are presented.

Etsion, I.↗
NASA NTRS1976

Nonaxisymmetric incompressible hydrostatic pressure effects in radial face seals

A flat seal having an angular misalinement is analyzed, taking into account the radial variations in seal clearance. An analytical solution for axial force, tilting moment, and leakage is presented that covers the whole range from zero to full angular misalinement. Nonaxisymmetric hydrostatic pressures due to the radial variations in the film thickness have a considerable effect on seal stability. When the high pressure is on the outer periphery of the seal, both the axial force and the tilting moment are nonrestoring. The case of high-pressure seals where cavitation is eliminated is discussed, and the possibility of dynamic instability is pointed out.

Etsion, I.↗
NASA NTRS1976

Optimum step design for centering of pistons moving in an incompressible fluid

Hydrodynamic effects are analyzed for a stepped piston moving within a tight clearance tube filled with an incompressible fluid. Hydrostatic effects are analyzed and a complete solution is obtained and an optimum step design for centering of the piston is suggested. The axial speed resulting from an axial driving force is calculated, and some experimental results for pistons falling in a water-filled tube are presented.

Etsion, I.↗
NASA NTRS1976

An accurate solution of the gas lubricated, flat sector thrust bearing

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗
NASA NTRS1976

The dual action gas thrust bearing - A new high load bearing concept

The principle of utilizing hydrodynamic effects in diverging films for improving load capacity in gas thrust bearings is discussed. A new concept of dual action bearing based on that principle is described and analyzed. The potential of the new bearing is demonstrated both analytically for an infinitely long slider and by numerical solution for a flat sector shaped thrust bearing. It is shown that the dual action bearing can extend substantially the range of load carrying capacity in gas lubricated thrust bearings and improve their efficiency.

Etsion, I.↗
NASA NTRS1976

Dual-action gas thrust bearing for improving load capacity

The principle of utilizing hydrodynamic effects in diverging films to improve the load carrying capacity in gas thrust bearings is discussed. A new concept of a dual action bearing based on that principle is described and analyzed. The potential of the new bearing is demonstrated both analytically for an infinitely long slider and by numerical solution for a flat sector shaped thrust bearing. It is shown that the dual action bearing can extend substantially the range of load carrying capacity in gas lubricated thrust bearings and can improve their efficiency.

Etsion, I.↗
NASA NTRS1976

Leakage-free journal bearings

A new concept of a journal bearing is developed which prevents side leakage of the lubricant, thus eliminating the need for sealing and collecting this leakage. The cooling of the bearing is accomplished by the prevailing circumferential flow. An analysis is performed and solutions are given for the bearing geometries and inlet pressures required to achieve the above purpose.

Pinkus, O.↗
NASA NTRS1976

Analysis of the gas-lubricated flat-sector-pad thrust bearing

A flat sector-shaped pad geometry for a gas-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. It is shown that maximum load capacity is achieved when the pad is tilted so as to create uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves, and a comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗