Engineering Papers⌕ Search

Engineering topics

Emilie J Siochi

Publications and source records attributed to Emilie J Siochi.

28 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Structural Health Monitoring of Vertical Lift Structures Operating in an Urban Environment

Verifying the structural integrity of aeronautical vehicles is of critical importance for the safety of passengers and crew. When operating in a densely populated urban area, pedestrian safety and collateral damage to buildings and other infrastructure also become important concerns. Damage modes, including fatigue from an increased frequency of take-off and landing cycles and a higher probability of impacts from bird strikes, also pose different failure risks as compared to commercial long-haul aircraft and thus require a change in structural health monitoring philosophy. This presentation will review the state of the art in structural health monitoring with an eye toward applications for vertical lift systems operated in the urban environment. Structural health monitoring methods including eddy current, fiber optic, ultrasonic plate wave, surface acoustic wave and electrical impedance tomography will be explored for use in on-board monitoring of impact and overstrain events as well as damage detection and characterization. Infusion of the data into an early warning system to help ensure damage will not propagate to failure during flight will also be discussed.

Russell A Wincheski↗
NASA NTRSDate not supplied

Design Analysis for Lunar Safe Haven Concepts

NASA’s plan to return humans to the lunar surface faces many challenges, especially in the sustained phases of the Artemis program. In combination with a habitat, a Lunar Safe Haven (LSH) would provide additional protection to crew, electronics, and equipment from the hazards of the space environment such as radiation, thermal extremes, micrometeoroids, and lunar dust. Influenced by the NASA Artemis program goals, the Lunar Safe Haven Study defined the high-level requirements, outlined the trade space for a LSH concept, and evaluated a set of concepts using a decision analysis structure. This paper will provide additional detail for two concepts that were designed and evaluated during the LSH study, the logic behind the choices, and some of the main driving design parameters.

lunar↗
NASA NTRSDate not supplied

Predicting Char Yield of High-Temperature Resins

A simulation technique has been developed for predicting the char yield of organic resins during high-temperature processing. In silico methods can aid in the screening of new advanced materials for a number of important properties, but no chemistry-sensitive protocol currently exists for predicting the important experimental value of char yield. The proposed method utilizes a reactive force field (ReaxFF) to model the chemical transformation of precursor monomers into carbonized structures during three processing stages: ramp-up to pyrolysis temperatures (~3000 K), pyrolysis, and quenching. Achieving good agreement with experimental char yields requires continuous removal of small by-product molecules to mimic outgassing, and the application of high pressure to encourage the formation of a dense, glassy network. Six different resin chemistries were investigated: an ethynyl, a phenylethynyl, a cyanate ester, a phthalonitrile, acrylonitrile, and adamantane. These candidates represent a diverse group of precursors with respect to initial cyclic content, presence of heteroatoms, and types of reactive groups. The protocol developed accurately predicts the relative char yield between the investigated chemistries and provides quantitative agreement with experimental values, especially for high char yield resins. Several simulated properties of the carbonized structures are compared with experimental results, including outgassing products, morphology of the final chemical configurations, cyclic content, and mechanical properties.

polymer simulations, molecular dynamics↗
NASA NTRSDate not supplied

Recent Advances in Structural Carbon Nanotube Composites

Carbon nanotubes (CNT) have been a subject of investigation for more than two decades. Part of the interest in CNTs was driven by CNT tensile mechanical properties at the nanoscale that suggest their potential to outperform state-of-the-art (SOA) lightweight structural materials. Early work on the development of CNT nanocomposites involved the dispersion of CNT powder into polymer matrices. Although low levels of CNT doping resulted in meaningful increases in electrical conductivity to enable applications such as electrostatic charge dissipation, the highest concentrations of CNTs in these lightly doped nanocomposites did not yield mechanical properties that could compete with SOA carbon fiber composites. The maximum concentration of CNTs in lightly doped nanocomposites was limited to about 5% due to increases in viscosity that prevent the fabrication of good quality nanocomposites. At the lower concentrations, properties of the resulting nanocomposites were analogous to those of composites made with very short, chopped carbon fibers. About ten years ago, CNTs became available in continuous fiber form, allowing the investigation of processing methods to incorporate much higher CNT content into composites. Recent developments in CNT composite fabrication have yielded improved mechanical properties and indicate that while some standard carbon fiber composite processing methods can be used, CNTs have unique microstructural features that require techniques tailored to access the hierarchical features of CNTs. This presentation will discuss the evolution of structural CNT mechanical property advancements and collaboration mechanisms for research across federal labs, academia, and industry that accelerated the maturation of structural CNTs.

Carbon Nanotubes↗
NASA NTRSDate not supplied

Carbon Fiber Composite Processing Using Isothermal Resins

To meet future demand for single-aisle composite aircraft production, manufacturing rates are expected to increase by up to six times current production rates. Resin infusion is a manufacturing method that has potential to enable fabrication of structures at the desired rates. However, production cycle times with currently available commercial infusion resins cannot support the rates needed for an estimated 80 aircraft per month. Recently, rapid-curing isothermal resins were developed that can reduce the overall processing time. These resins can be infused, cured, and demolded at a single temperature below 100 °C, thereby eliminating the need for time consuming temperature ramps and shortening the overall cure time. In addition, the low temperatures enable use of low-cost tooling during production. This presentation will discuss the use of resin transfer molding to produce composites with rapid-curing isothermal resins, manufacturing considerations, and performance characteristics of the composites.

John M Gardner↗