Engineering Papers⌕ Search

Engineering topics

Elliott, Amy M.

Publications and source records attributed to Elliott, Amy M..

At least 19 records

Material selection and manufacturing for high‐temperature heat exchangers: Review of state‐of‐the‐art development, opportunities, and challenges

Abstract Many energy systems demand heat transfer at high temperatures to keep up with high demand for power, so high‐temperature material that can perform and last under these harsh conditions is needed for heat exchangers. The engineering requirements for these high‐temperature heat exchanger material call for high thermal conductivity, high resistance to fracture, high resistance to creep deformation, environmental stability in environments associated with the application, and high modulus of elasticity while maintaining low cost to make and maintain. Naturally, ceramics are a good solution for this endeavor. In the past, high‐temperature heat exchangers made from ceramics have been used. We provide examples of ceramics in relevant heat exchange applications and provide motivation where additive manufacturing (AM) can improve efficiency. AM for the relevant material is under development, and we provide insight on the AM of ceramic materials and examples of AM heat exchangers keeping cost in mind. The motivation of the review paper is to provide a framework for material and manufacturing selection for high‐temperature heat exchangers for AM to keep up with the demand for better efficiency, better material, better manufacturing, and cost moving forward with AM technology in high‐temperature ceramic heat exchangers.

36 MATERIALS SCIENCE↗

Advances in Binder Jet Additive Manufacturing

Binder Jetting is a powerful additive manufacturing technology due to its low cost and wide range of types of materials it can shape. The industry partner ExOne has a range of binder jet products for applications such as casting tools, composite layup tools, single-alloy metal components, and more. As such, research and development is of high interest in the area of specialized binders for each type of material, processing technology that improves reliability and quality, and materials to enhance the performance of the final parts. Thus, this work focuses on developing novel binders for sand tools and metal prints, new capabilities in multi-material printing, and build monitoring and correction. The result of this work includes a novel binder system that makes binder jet sand stronger than concrete while still being water soluble, a casting binder that is environmentally friendly and produces better surface finishes on castings, and a binder for metals that reduces the residual carbon.

36 MATERIALS SCIENCE↗

Indirect additive manufacturing process

A method for indirect additive manufacturing of an object, the method comprising: (i) separately feeding a powder from which said object is to be manufactured and either a difunctional curable monomer according to Formula (I) or an adhesive polymer binder into an additive manufacturing device; (ii) dispensing selectively positioned droplets of said difunctional curable monomer or adhesive polymer binder, from a printhead of said additive manufacturing device, into a bed of said powder to bind particles of said powder with said difunctional curable monomer or adhesive polymer binder to produce a curable preform having a shape of the object to be manufactured; and, in the case of the difunctional curable monomer, (iii) curing said curable preform to form a crosslinked object.

Saito, Tomonori↗

Indirect additive manufacturing process using amine-containing adhesive polymers

A method for binder jetting additive manufacturing of an object, the method comprising: (i) separately feeding a powder from which said object is to be manufactured and a solution comprising an adhesive polymer dissolved in a solvent into an additive manufacturing device, wherein said adhesive polymer is an amine-containing polymer having a molecular weight of at least 200 g/mole and is present in said solution in a concentration of 1-30 wt % to result in said solution having a viscosity of 2-25 mPa·s and a surface tension of 25-45 mN/m at room temperature; and (ii) dispensing selectively positioned droplets of said adhesive polymer, from a printhead of said additive manufacturing device, into a bed of said powder to bind particles of said powder with said adhesive polymer to produce a preform having a shape of the object to be manufactured.

Saito, Tomonori↗

3D-printed B 4 C collimation for neutron pressure cells

A design for an incident-beam collimator for the Paris–Edinburgh pressure cell is described here. This design can be fabricated from reaction-bonded B 4 C but also through fast turnaround, inexpensive 3D-printing. 3D-printing thereby also offers the opportunity of composite collimators whereby the tip closest to the sample can exhibit even better neutronic characteristics. Here, we characterize four such collimators: one from reaction-bonded B 4 C, one 3D-printed and fully infiltrated with cyanoacrylate, a glue, one with a glue-free tip, and one with a tip made from enriched 10 B 4 C. The collimators are evaluated on the Spallation Neutrons and Pressure Diffractometer of the Spallation Neutron Source and the Wide-Angle Neutron Diffractometer at the High Flux Isotope Reactor, both at Oak Ridge National Laboratory. This work clearly shows that 3D-printed collimators perform well and also that composite collimators improve performance even further. Beyond use in the Paris–Edinburgh cell, these findings also open new avenues for collimator designs as clearly more complex shapes are possible through 3D printing. An example of such is shown here with a collimator made for single-crystal samples measured inside a diamond anvil cell. These developments are expected to be highly advantageous for future experimentation in high pressure and other extreme environments and even for the design and deployment of new neutron scattering instruments.

47 OTHER INSTRUMENTATION↗

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗

High-Performance Titanium Oxynitride Thin Films for Electrocatalytic Water Oxidation

TiN x O y (TiNO) thin films with superior electrochemical properties have been synthesized in situ using a pulsed laser deposition method and a varied oxygen partial pressure from 5 to 25 mTorr. In this study, the electrochemical overpotential of these TiNO films for water oxidation was found to be as low as 290 mV at 10 mA/cm 2 , which is among the lowest overpotential values reported. The Tafel slopes, indicative of a rate of increase of electrode potential with respect to current, for these films are determined to be in the range of 85–57 mV/decade. These results further demonstrate the superiority of TiNO thin film as electrocatalyst for water oxidation to generate fossil-free fuels. The improvement in the electrocatalytic behavior of the semiconducting TiNO thin films is explained based on an adjustment in the valence band maximum edge and an enhancement in the number of electrochemically active sites. Both effects are realized by the substitution of N by O, forming a TiNO lattice that is isostructural with the rock-salt TiN lattice. These findings appear to assume significant importance in light of water electrolysis to produce fuels for the development of environmentally friendly power sources.

36 MATERIALS SCIENCE↗

Binder jet additive manufacturing method to fabricate near net shape crack-free highly dense Fe-6.5 wt.% Si soft magnets

High silicon (Si) electrical steel has the potential for efficient use in applications such as electrical motors and generators with cost-effective in processing, but it is difficult to manufacture. Increasing the Si content beyond 3 wt.% improves magnetic and electrical properties, with 6.5 wt.% being achievable. The main goal of this research is to design, develop, and implement a scalable additive manufacturing process to fabricate Fe with 6.5 wt.% Si (Fe–6Si) steel with high magnetic permeability, high electrical resistivity, low coercivity, and low residual induction that other methods cannot achieve because of manufacturing limitations. Binder jet additive manufacturing was used to deposit near net shape components that were subsequently sintered via solid-state sintering to achieve near full densification. Here, it is shown that the use of solid-state sintering mitigates cracking since no rapid solidification occurs unlike fusion-based additive technologies. The Fe–6Si samples demonstrated an ultimate tensile strength of 434 MPa, electrical resistivity of 98 μΩ cm, and saturation magnetization of 1.83 T with low coercivity and high permeability. The results strongly supports to replace the only available 0.1 mm thick chemical vapor deposition (CVD) produced Si steel using the cost effective AM method with good mechanical and magnetic properties for motor ap

36 MATERIALS SCIENCE↗

Binder jet printed WC infiltrated with pre-made melt of WC and Co

WC-Co was made via binder jet additive manufacturing of tungsten carbide followed by melt infiltration with a Co-WC infiltrant. The goal of the study was to achieve fully densified parts in near-net shape with minimal shrinkage while keeping the Co content low. The exact amount of infiltrant was determined in order to fully densify with minimum shrinkage based on the actual volume taken up by WC powder in the preform based on theoretical density, the bounding volume of prints after shrinkage, and the volume from the infiltrant. The eutectic nature of the infiltrant enabled melting at much lower temperature compared to the melting temperature of pure Co. The density, microstructure, grain size, hardness, and fracture toughness were characterized. The shrinkage and net shaping were assessed with light scans. A detailed look at the fracture mechanics was assessed. Here, this approach achieved highly dense WC-Co parts in net-shape with Co vol% of near 29 (Co wt% ~19), density of 96.2% theoretical, hardness of 8.34 GPa, grain size of 7.7 μm, magnetic saturation of 0.5 T, room temperature thermal conductivity of 125 W/mK, and fracture toughness of 24.7 = MPa·m 1/2 .

36 MATERIALS SCIENCE↗

Shape retention and infiltration height in complex WC-Co parts made via binder jet of WC with subsequent Co melt infiltration

Additive manufacturing (AM) of complex tungsten carbide-cobalt (WC-Co) parts was achieved using binder jet additive manufacturing (BJAM) of WC powders followed by Co infiltration. The intent of the study is to explore the shape retention, infiltration height, and properties of parts made with this method. Using BJAM with infiltration of the metal phase can limit shrinkage and grain growth in ceramic-metal (cermet) composites compared to other additive manufacturing (AM) methods. Knowledge of previous infiltration studies was used to help process parts to imitate production of parts. The properties such as density, microstructure, grain size, and hardness of the parts are characterized along the infiltration height. Fracture toughness is measured where applicable. Furthermore, this approach has the potential to achieve highly dense WC-Co parts that are net-shaped with some ternary phase and z-direction distortion.

36 MATERIALS SCIENCE↗

Microstructure evolution during near-net-shape fabrication of Ni x Al y -TiC cermets through binder jet additive manufacturing and pressureless melt infiltration

Titanium carbide-nickel aluminide (TiC-Ni x Al y ) intermetallic matrix composite materials were fabricated with additive manufacturing and pressureless melt infiltration for applications intended for high-wear and corrosive environments while maintaining low density. In this work, two compositions of nickel aluminide are infiltrated into porous, printed TiC preforms. Net shaping of a nickel-rich infiltrant is less compared to the net shaping of the aluminum-rich infiltrant due to dissolution of TiC in the molten infiltrant. The microstructures and porosity of the two infiltrants with TiC are examined after processing. The explanation of shape retention from infiltration is explained, and the excellent shape retention in an Al-rich infiltrant system is thought to be from peritectic behavior and a metered infiltration of different phases during cooling and solidification without significant dissolution. The metered infiltration contributed to some porosity, microcracking, and segregated Ni x Al y phases. We show that TiC can be shaped and infiltrated with intermetallics to provide a method of making composites with limited shrinkage and controlled geometry.

36 MATERIALS SCIENCE↗

Highly dense, inexpensive composites via melt infiltration of Ni into WC/Fe preforms

Generally, WC-based composites use Co as the metal binder phase to consolidate using liquid-phase sintering with a small percentage of Co, but a potentially lower cost binder phase can be made with a different approach when using large amount of metal binder phase. FeNi as a metal binder material is much cheaper than Co. WC can be liquid-phase sintered and melt infiltrated with FeNi, but by making FeNi in situ , costs lower even further. Composites of WC-(Fe-Ni) were made by first pressing a mixture of WC and Fe powders and subsequently melt infiltrating Ni in an amount corresponding to less volume than the porosity of the preform to ensure high WC content. The research objective was to make highly dense composites via melt infiltration with a low-cost metal binder phase in situ . This approach has the potential to make fully dense composites, rather than hardmetals, with suitable properties at lower costs. The density and hardness are 97.4%TD and 6.72 GPa, respectively.

36 MATERIALS SCIENCE↗

Infiltration studies of additive manufacture of WC with Co using binder jetting and pressureless melt method

Additive manufacturing (AM) of tungsten carbide-cobalt (WC-Co) is explored starting with WC preforms shaped with binder jet additive manufacturing (BJAM) followed by melt infiltration of Co. The research objective is to demonstrate the ability to net-shape WC-Co composites through BJAM of a WC preform followed by backfilling with cobalt via pressureless infiltration. This method also has the potential to minimize shrinkage and grain growth compared to other AM techniques. The effects of sintering, Co content, and infiltration time on the net shaping and properties of processed composites are shown. The best shaped material had an average grain size of 5.1 μm, 32 vol.% Co, density of 98.54% theoretical, fracture toughness of 23.2 MPa m 1/2 , and hardness of 9.0 GPa. Data presented illustrates that the proposed approach results in favorable ceramic-metal (cermet) properties and is viable for fabricating cermets of other material combinations. Furthermore successful AM of cermets provides complex geometries, high throughout, and low costs.

36 MATERIALS SCIENCE↗

Comparison of characterization methods for differently atomized nickel-based alloy 625 powders

The deployment of additive manufacturing depends on the quality of the produced part, specifically the absence of internal defects, impurities and compositional gradient. In this paper, differently atomized nickel-based alloy 625 powder particles were systematically characterized with different methods and results were compared. Powder properties were studied to understand the effect of different atomization methods on the properties of the powder particles. Morphology, shape and size of water and argon atomized powders were observed using optical microscopy, scanning electron microscopy and micro-computed X-ray tomography (μCT); μCT with different resolution and sample setup. As expected, water atomized powder particles have irregular morphology in contrast to spherical gas atomized particles. Phase and elemental analysis were conducted with X-ray diffraction and energy dispersive spectroscopy; thermal properties were measured with differential scanning calorimetry. Gas atomized powder shows composition and melting temperature close to nominal bulk alloy 625. Particle size analysis was carried out using sieving, laser particle size analysis and μCT. It is found that the average particle size obtained from μCT depends on scan resolution. Additionally, porosity of the powders was observed in SEM micrographs and investigated in detail using μCT. In conclusion, μCT with higher resolution results in collecting accurate shape, size, porosity and morphology of the powder particles. Finally, considering the large number of particles that can be investigated with μCT and ability to observe internal porosity, μCT is found to be an appropriate if not superior substitution for other powder characterization methods such as optical/electron microscopies, sieving and laser particle size analysis if time of characterization is not a concern.

36 MATERIALS SCIENCE↗

The Development and Implementation of Instruction and Remote Access Components of Additive Manufacturing

Additive manufacturing (AM), also known as 3D printing, is one of the latest emerging widespread production technologies. Almost any complex-part geometry is easily made using this technology and is usually used reliably. Many implementations of AM exist from areas as diverse as food industry to biomedical engineering; such a broad-spectrum usage of this technology makes it extremely attractive when combined with its low cost, reliability, color range, and complexity abilities.Though the cost of buying new AM machines varies greatly depending on the size of the machines (AM equipment ranges from desktop printers to very large production machines), AM equipment is still not affordable for many educational institutions due to limited or low equipment, consumable supplies, physical space, and maintenance budgets. Such issues become even more important for educational organizations in underserved and underdeveloped districts, which typically have inadequate support from their constituents.To address this issue, AM laboratories and their functionalities can easily be made available through the internet. Educational institutions which do not have the capability of AM technologies can easily access and utilize other laboratories’ capabilities. In the past, various remotely accessible AM laboratories such as these have been introduced, and their advantages and limitations in various P16 STEM (science, technology, engineering, and mathematics) practices have been reported. In this chapter, the authors introduce a novel concept of accessing external AM laboratories via smartphones and advanced computer technologies.

Fidan, Ismail↗

Additive Manufacturing of Highly Reactive Lanthanides

Additive manufacturing (AM) is a unique type of fabrication that builds objects layer-by-layer from virtually any feedstock. When compared to traditional, subtractive manufacturing, AM wastes less feedstock material, which makes it ideal for the shaping of magnetic materials. Furthermore, complex geometries with advanced heat and mass transport properties can be created out of highly reactive lanthanides which could not be created with traditional manufacturing. This work describes the results of shaping these materials into high-resolution microchannel geometries via additive manufacturing and the resulting characteristics of the printed artifacts.

Elliott, Amy M.↗