Engineering topics

Eldred, Jeffrey [Fermilab]

Publications and source records attributed to Eldred, Jeffrey [Fermilab].

4 records

DOE OSTI2026

Optimization and stabilization of Fermilab Booster using hybrid Bayesian/RL framework

PIPII project will raise Fermilab Booster intensity and ramp rate. Beam losses will limit average power and are hard to simulate. Presently, Booster uses operator-guided empirical tuning. This task is challenging due to high dimensionality, multiple objectives, critical safety constraints, and drifts. We developed a synergistic suite of Bayesian optimization (BO) and reinforcement learning (RL) tools to optimize and stabilize beam losses. First, active learning was used to build a rough model. Data was collected parasitically using two novel safety constraint types – nonlinear input space restrictions (based on optics model), and uncertainty constraints (to stop bad steps/beam aborts). We then applied online multi-objective BO with scalarized objectives and fitting to improve/rebalance losses, increasing safety margins by 25%. Using BO model as a safety veto, we tried several on/off-policy RL agents for long term stabilization; SAC had best performance. We found that adding contextual (state) information further improved performance, eventually integrating key knobs like linac phase and temperature into the parameter space. Long term testing is ongoing to enable operational use.

Kuklev, Nikita [Fermilab]↗

DOE OSTI2026

IOTA experiment for proton pulse compression at extreme space-charge

A gammaT scheme may be required for the PIP-II era performance or ACE-MIRT era performance of the Booster. PIP-II era operations of the Fermilab proton complex will require the Fermilab Booster to increase beam intensity from 4.5e12 to 6.5e12 protons, while also increasing its ramp from 15 Hz to 20 Hz. These changes pose particular challenges for transition-crossing in the Booster, where longitudinal beam quality must be controlled in order to facilitate slip-stacking in the Recycler Ring later in the Main Injector cycle. Two novel gammaT jump schemes are proposed, termed “double gammaT jump” and “partial gammaT jump”, which optimize the magnitude of the gammaT jump within optics and power supply constraints.

Eldred, Jeffrey [Fermilab]↗

DOE OSTI2026

IOTA experiment for proton pulse compression at extreme space-charge

The longitudinal compression of intense proton bunches with strong space-charge force is an essential component of a proton driver for a muon collider. We propose a proton bunch compression experiment at the Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab to explore optimal radio frequency (RF) cavity and lattice configurations. IOTA is a compact fixed-energy storage ring dedicated to beam physics R&D that can circulate a 2.5-MeV proton beam with extreme space-charge. Using ImpactX and its 3D space-charge solver, simulations indicate that bunch length can be rapidly reduced by a factor of at least two, without appreciable degradation in transverse beam quality, even under strong space-charge conditions. However, longitudinal defocusing presents a large effect in short-pulsed proton beams, and the optimization of bunch compression under such conditions is discussed.

Simons, Benjamin [Northern Illinois U.; Fermilab]↗

DOE OSTI2025

Fermilab Booster loss modelling and rebalancing using Bayesian methods

Fermilab Booster is being upgraded for the PIP-II project to support 20Hz ramp rate at higher intensities. Loss trip limits determine the achievable peak power. To meet PIP-II requirements, losses need to be halved as compared to current levels. Losses primarily occur at injection and transition crossing, with both gradually increasing and threshold-like intensity-dependent behaviors. The existing simulation models are not yet good enough for quantitative loss predictions. In practice, it will be necessary to tune up the Booster using iterative methods and operator intuition. In this paper we present an effort to systematically model Booster losses using active learning (Bayesian exploration) techniques, and subsequently to rebalance them for higher trip limit margins. We first created several sets of spatially and temporally isolated orbit and optics knobs, and trained Gaussian process models for each beam loss monitor as well as beam current. This is a complex task due to safety and timing requirements – we discuss mitigations such as uncertainty constraints and approximate fitting. Once models are stable, we perform large-scale single and multi-objective tuning using scalarized objectives made up of critical beam loss locations. Our results demonstrate significant rebalancing of losses, increasing trip margins, as well as an overall improvement in beam transmission efficiency. We are exploring how to combine existing simulations with experimental data and automate the collection procedure so that more advanced surrogate models can be created over time.

Kuklev, Nikita [Fermilab]↗