Engineering Papers⌕ Search

Engineering topics

Edwards, Matthew K.

Publications and source records attributed to Edwards, Matthew K..

At least 19 records

PNNL FY 2022 Sibling Pin Testing Results

This report presents the results of testing two rods after heat treatment at 400C for 8 hours and compares to the results from FY 2021 of similar rods that were tested as baseline. The heat treatment resulted in a decrease in yield stress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

PNNL FY2021 Sibling Pin Testing Results

The post-irradiation examination, axial tensile, burst, and four-point bend testing results of the first two sibling pins, 6U3/L8 and 5K7/P2 are presented.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal properties of U-Mo alloys irradiated under high fission power density

A variety of physical and thermal property measurements made on irradiated U-Mo alloy monolithic fuel samples with a Zr diffusion barrier and clad in Al alloy 6061 are reported. These properties form the basis for additional investigations in thermal behavior of U-Mo fuel under high performance research reactor irradiation conditions. Measurements were performed on samples harvested from fuel plates irradiated under high fission power density and surface heat flux and complement previous measurements on samples subjected to moderate fission power density and surface heat flux. Specific heat capacity of irradiated monolithic U-Mo increases with increasing temperature and fission density, but carries large uncertainties associated with thickness measurements used to determine the mass fraction of the layer constituents for extraction of the U-Mo specific heat capacity, specifically the very thin and nonuniform Zr diffusion barrier. Density of irradiated monolithic U-Mo decreases with increasing fission density resulting from fission gas swelling and porosity formation. Thermal diffusivity of irradiated monolithic U-Mo increased with increasing temperature and decreased with increasing fission density. Thermal conductivity of irradiated monolithic U-Mo increased with increasing temperature, and in general, appeared to decrease and become less sensitive to temperature with increasing fission density. Thermal conductivity measurements compared to a semi-empirical model agreed within ±30%. It is suspected that the main driver in deviation between model calculations and measurements is the fission gas swelling determination, which does not account for fission power density or irradiation temperature.

uranium (U), molybdenum, nuclear fuel, thermal con↗

Synthesis of Plutonium Oxide Specimens for a Statistically Designed Nuclear Forensics Study

This report describes the synthesis of plutonium oxide (PuO 2 ) samples at a bench-scale (10 g Pu) to support nuclear forensics research. The key unit operations that were performed included dissolving the PuO 2 feed material, purifying the Pu by ion exchange, precipitating as plutonium (III) oxalate, and reconverting to PuO 2 by calcination of the oxalate compound. Seventy-six PuO 2 synthetic runs were performed in execution of a statistically designed test matrix. The process parameters varied in these synthesis runs included temperature (30 or 50 °C), the Pu concentration in the feed solution (10, 30, or 50 g Pu/L), the HNO 3 concentration in the feed solution (1, 2, or 3 M), the direction of reagent addition (direct or reverse strike), the source of oxalic acid (solid or solution), and the reagent addition rate (as fast as possible, 20, or 40 minutes). This report describes the synthesis of the 76 PuO 2 specimens. The characterization of these specimens will be described in separate reports.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

A Workshop on the History of Plutonium Processing at Hanford Washington as the Foundation for Modern-day Plutonium Process Science

Numerous national laboratories in the United States have roots related to the Manhattan Project that contributed to the end of World War II. The pioneering science and engineering that took place over the decades that followed continues to influence modern-day actinide-related research at those institutions, leading to unique strengths and cutting-edge ideas and perspectives. These same national laboratories also face a challenge: figuring out how to capture the expertise of a retiring workforce who had first-hand experience in these pioneering nuclear efforts. Recently, at PNNL a “Train-the-Trainer” approach has been piloted where mentors and mentees are paired together to develop and deliver interactive workshops on historical topics that relate to modern-day research, such as Plutonium Processing or Environmental Management of Legacy Nuclear Waste. This approach was used to develop a workshop that beings with the Historic Hanford process plutonium chemistry and engineering, describes its influence on current plutonium separation and process science, and then details the chemistry of plutonium as it progresses from a minor constituent in irradiated fuel to purified solid product. This workshop is targeted to the practitioner of applied science and technology wishing to gain a better understanding of the history and process-related chemistry of element 94 so that they may better direct the tools of their specific craft toward the present and future needs of plutonium science.

Smith, Frances N.↗

Evaluation of Crystal Accumulation in High Level Waste Glasses with Research-Scale Melter

The report summarizes the experimental results from a long term Research Scale Melter (RSM) test which was performed at Pacific Northwest National Laboratory (PNNL) in FY16 to answer questions on the effects of spinel crystal accumulation on melter performance and operational longevity. The RSM was used to vitrify a surrogate waste material of the Hanford AZ-101 tank waste composition. This waste contains a high concentration of Fe and Ni and is susceptible to precipitation of a large quantity of spinel crystals during vitrification. The RSM test was run over a period of 11 weeks and consisted of eleven feeding/pouring and idling periods. The feeding/pouring periods were 36 h long while the idling periods ranged from 4 to 7 days. Approximately 509 kg of feed was processed, producing ~159 kg of glass. The main goal of this test was to determine if the riser of the melter can be clogged by accumulated layer of spinel crystals which precipitated from glass during multiple idling’s. In addition, the glass samples were collected during each pouring to evaluate a possibility of a partial or complete removal of crystal deposits accumulated during idling. Furthermore, an electrical conductivity probe was tested for monitoring the crystal accumulation in the riser of the melter during idling’s. The test was concluded by dissecting the melter and preparing cross-sections to determine layer thickness, crystal size and morphology of spinel crystals in the bulk of the melter and in the glass riser.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

FY16 Status of Immersion Phased Array Ultrasonic Probe Development and Performance Demonstration Results for Under Sodium Viewing

This section of the Joint summary technical letter report (TLR) describes work conducted at the Pacific Northwest National Laboratory (PNNL) during FY 2016 (FY16) on the under-sodium viewing (USV) PNNL project 58745, work package AT-16PN230102. This section of the TLR satisfies PNNL’s M3AT-16PN2301025 milestone and is focused on summarizing the design, development, and evaluation of two different phased-array ultrasonic testing (PA-UT) probe designs—a two-dimensional (2D) matrix phased-array probe, and two one-dimensional (1D) linear array probes, referred to as serial number 4 (SN4) engineering test units (ETUs). The 2D probe is a pulse-echo (PE), 32×2, 64-element matrix phased-array ETU. The 1D probes are 32×1 element linear array ETUs. This TLR also provides the results from a performance demonstration (PD) of in-sodium target detection trials at 260°C using both probe designs. This effort continues the iterative evolution supporting the longer term goal of producing and demonstrating a pre-manufacturing prototype ultrasonic probe that possesses the fundamental performance characteristics necessary to enable the development of a high-temperature sodium-cooled fast reactor (SFR) inspection system for in-sodium detection and imaging.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Highly Selective Colorimetric and Luminescence Response of a Square-Planar Platinum(II) Terpyridyl Complex to Aqueous TcO 4 –

Molecular recognition of an aqueous pertechnetate (TcO 4 – ) anion is fundamentally challenging partly due to the charge-diffuse nature of this anion, which hampers design of new technologies for its separation and detection. Here, to address this gap, simple salts of transition metal complexes that undergo a distinct spectroscopic change upon exposure to aqueous anions were explored. The Pt(II) complex [Pt(tpy)Br]SbF 6 (tpy = 2,2′;6′,2″-terpyridine) undergoes a dramatic color change and intense luminescence response upon TcO 4 – uptake due to concomitant enhancement of Pt···Pt interactions. The spectroscopic response was highly selective and quantitative for aqueous TcO 4 – among other competing anions. Complementary Raman spectroscopy and microscopy techniques, structural determination, and theoretical methods were employed to elucidate the mechanism of this response at the molecular level.

anions↗

FY15 Status of Immersion Phased Array Ultrasonic Probe Development and Performance Demonstration Results for Under Sodium Viewing

This Technical Letter Report (TLR) describes work conducted at the Pacific Northwest National Laboratory (PNNL) during FY 2015 on the under-sodium viewing (USV) PNNL project 58745, Work Package AT-15PN230102. This TLR satisfies PNNL’s M3AT-15PN2301027 milestone, and is focused on summarizing the design, development, and evaluation of a two-dimensional matrix phased-array probe referred to as serial number 3 (SN3). In addition, this TLR also provides the results from a performance demonstration of in-sodium target detection trials at 260°C using a one-dimensional 22-element linear array developed in FY14 and referred to as serial number 2 (SN2).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Design of the Laboratory-Scale Plutonium Oxide Processing Unit in the Radiochemical Processing Laboratory

This report describes a design for a laboratory-scale capability to produce plutonium oxide (PuO 2 ) for use in identifying and validating nuclear forensics signatures associated with plutonium production, as well as for use as exercise and reference materials. This capability will be located in the Radiochemical Processing Laboratory at the Pacific Northwest National Laboratory. The key unit operations are described, including PuO 2 dissolution, purification of the Pu by ion exchange, precipitation, and re-conversion to PuO 2 by calcination.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Fuel Thermo-physical Characterization Project. Fiscal Year 2014 Final Report

The Office of Material Management and Minimization (M3) Reactor Conversion Fuel Thermo-Physical Characterization Project at Pacific Northwest National Laboratory (PNNL) was tasked with using PNNL facilities and processes to receive irradiated low enriched uranium–molybdenum (LEU-Mo) fuel plate samples and perform analysis in support of the M3 Reactor Conversion Program. This work is in support of the M3 Reactor Conversion Fuel Development Pillar that is managed by Idaho National Laboratory. The primary research scope was to determine the thermo-physical properties as a function of temperature and burnup. Work conducted in Fiscal Year (FY) 2014 complemented measurements performed in FY 2013 on four additional irradiated LEU-Mo fuel plate samples. Specifically, the work in FY 2014 investigated the influence of different processing methods on thermal property behavior, the absence of aluminum alloy cladding on thermal property behavior for additional model validation, and the influence of higher operating surface heat flux / more aggressive irradiation conditions on thermal property behavior. The model developed in FY 2013 and refined in FY 2014 to extract thermal properties of the U-Mo alloy from the measurements conducted on an integral fuel plate sample (i.e., U-Mo alloy with a thin Zr coating and clad in AA6061) continues to perform very well. Measurements conducted in FY 2014 on samples irradiated under similar conditions compare well to measurements performed in FY 2013. In general, there is no gross influence of fabrication method on thermal property behavior, although the difference in LEU-Mo foil microstructure does have a noticeable influence on recrystallization of grains during irradiation. Samples irradiated under more aggressive irradiation conditions, e.g., higher surface heat flux, revealed lower thermal conductivity when compared to samples irradiated at moderate surface heat fluxes, with the exception of one sample. This report documents thermal property measurements conducted in FY 2014 and compares results to values obtained from literature and measurements performed in FY 2013, where applicable, along with appropriate discussion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

LEU-Mo Fuel Out-of-Pile Characterization for TUM (Final Report)

The Technische Universität München (TUM) located in Germany requested that Pacific Northwest National Laboratory (PNNL) perform thermal-physical property measurement services for determining the thermal conductivities of irradiated U-Mo dispersion fuel samples. Two dispersion fuel segments containing U-7Mo dispersion fuel in an Al-2wt% Si matrix harvested from the AFIP-1 irradiation experiment were provided to PNNL for this effort. The segments were sectioned into samples for pycnometry (density) and laser flash analysis (thermal diffusivity), differential scanning calorimetry (specific heat capacity), and optical metallography (thickness, image analysis). This report summarizes the findings of the analysis performed at TUM’s request.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Identify and Quantify the Mechanistic Sources of Sensor Performance Variation Between Individual Sensors SN1 and SN2

This Technical Letter Report satisfies the M3AR-14PN2301022 milestone, and is focused on identifying and quantifying the mechanistic sources of sensor performance variation between individual 22-element, linear phased-array sensor prototypes, SN1 and SN2. This effort constitutes an iterative evolution that supports the longer term goal of producing and demonstrating a pre-manufacturing prototype ultrasonic probe that possesses the fundamental performance characteristics necessary to enable the development of a high-temperature sodium-cooled fast reactor inspection system. The scope of the work for this portion of the PNNL effort conducted in FY14 includes performing a comparative evaluation and assessment of the performance characteristics of the SN1 and SN2 22 element PA-UT probes manufactured at PNNL. Key transducer performance parameters, such as sound field dimensions, resolution capabilities, frequency response, and bandwidth are used as a metric for the comparative evaluation and assessment of the SN1 and SN2 engineering test units.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Conceptual Design for the Pilot-Scale Plutonium Oxide Processing Unit in the Radiochemical Processing Laboratory

This report describes a conceptual design for a pilot-scale capability to produce plutonium oxide for use as exercise and reference materials, and for use in identifying and validating nuclear forensics signatures associated with plutonium production. This capability is referred to as the Pilot-scale Plutonium oxide Processing Unit (P3U), and it will be located in the Radiochemical Processing Laboratory at the Pacific Northwest National Laboratory. The key unit operations are described, including plutonium dioxide (PuO2) dissolution, purification of the Pu by ion exchange, precipitation, and conversion to oxide by calcination.

plutonium oxide↗

Development and validation of capabilities to measure thermal properties of layered monolithic U-Mo alloy plate-type fuel

The uranium-molybdenum (U-Mo) alloy in a monolithic form has been proposed as one fuel design capable of converting some of the world’s highest power research reactors from the use of high enriched uranium (HEU) to low enriched uranium (LEU). One aspect of the fuel development and qualification process is to demonstrate appropriate understanding of thermal conductivity behavior of the fuel system as a function of temperature and expected irradiation conditions. The purpose of this paper is to verify and validate the functionality of equipment methods installed in hot cells for eventual measurements on irradiated uranium-molybdenum (U-Mo) monolithic fuel specimens, procedures to operate the equipment, and models to extract the desired thermal properties. The results presented here demonstrate the adequacy of the equipment, procedures and models that have been developed for this purpose based on measurements conducted on surrogate depleted uranium-molybdenum (DU-Mo) alloy samples containing a zirconium diffusion barrier and clad in aluminum alloy 6061 (AA6061). The results are in excellent agreement with thermal property data reported in the literature for similar U-Mo alloys as a function of temperature.

multi-layer↗