Engineering Papers⌕ Search

Engineering topics

Edwards, F. G.

Publications and source records attributed to Edwards, F. G..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Tests Of A Differential Global Positioning System

Paper describes validation tests of global positioning system (GPS) for low-flying helicopters. Configured as differential GPS, in which components in both aircraft and ground station compute position errors relative to known location using satellite navigational data. Corrections computed from differences between computed and measured ranges to four satellites being tracked by receiver in both aircraft and ground systems. Tests conducted to determine whether equipment and computer programs of system operated correctly and consistently.

Edwards, F. G.↗
NASA NTRS1989

Flight-test evaluation of civil helicopter terminal approach operations using differential GPS

A civil code differential Global Positioning System (DGPS) has been developed and flight-tested by the NASA Ames Research Center. The system was used to evaluate the performance of the DGPS for support of helicopter terminal approach operations. The airborne component of the DGPS was installed in a NASA helicopter. The ground-reference component was installed in a mobile van and equipped with a real-time VHF telemetry data link to transmit correction information to the aircraft system. An extensive series of tests was conducted to evaluate the performance of the system for several different configurations of the airborne navigation filter. This paper will describe the systems, the results of the flight tests, and the results of the posttest analysis.

Edwards, F. G.↗
NASA NTRS1988

Validating the airborne and ground based components of a differential GPS system

A differential GPS mechanization of an external data link concept under development at NASA Ames Research Center is discussed. The system is intended to evaluate the use of differential GPS to support helicopter approach operation. Analytical techniques for static testing and evaluation of the system hardware and software performance in real time are described. Several techniques that have been used to detect and rectify a specific problem encountered during the tests are dicussed. An example of flight test results using the validated system is provided.

Edwards, F. G.↗
NASA NTRS1987

Helicopter terminal approach using differential GPS with vertical-axis enhancement

The NAVSTAR Global Positioning System (GPS) in differential mode (DGPS) has been shown to be least accurate in the vertical axis. The vertical axis also has the most stringent accuracy requirements for aircraft precision approach and landing. A series of flight tests were conducted to evaluate a concept for improving the DGPS vertical axis navigation performance. These tests incorporated augmentation sensors to aid the DGPS navigation solution during terminal approach operations. A GPS receiver was installed on board a NASA helicopter and interfaced with a real-time digital computer system. A reconfigurable navigation filter programmed in the digital computer provided an augmented DGPS solution, with selectable inputs from a low-cost vertical accelerometer, a barometric altimeter, and the aircraft attitude gyros. The reference aircraft position was determined by a laser tracker. Extensive post-test analysis was done to optimize the filter performance during the terminal approach operation. Test results show that baro-altimeter aiding can significantly improve vertical axis performance. Follow-on tests are planned for the optimized configurations.

Edwards, F. G.↗
NASA NTRS1985

Civil helicopter flight operations using differential GPS

The results of NASA flight trials of a dual-receiver differential global positioning system (DGPS) for civilian helicopter navigation applications, are presented. The three principal components of the DGPS system are described, including the GPS ground-reference system, a range tracking system, and an on-board sequential GPS receiver. The ground-based receiver in the DGPS operates at a known fixed location and receives C/A code signals from NAVSTAR satellites. System bias errors in the ground receiver are subtracted from the airborne solution for the navigational fix. Calculations of the differential bias error are carried out using an on-board PDP-11/34 M research computer. The ground-reference differential corrections for satellites are given in a table. It is shown that the differential correction signal of the DGPS contains only a small (0.1 rad/sec) high-frequency component which can be attributed to system error. A schematic diagram of the DGPS postflight data processing routine is provided.

Edwards, F. G.↗
NASA NTRS1984

Operation of a single-channel, sequential Navstar GPS receiver in a helicopter mission environment

It is pointed out that the future utilization of the Navstar Global Positioning System (GPS) by civil helicopters will provide an enhanced performance not obtainable with current navigations systems. GPS will supply properly equipped users with extremely accurate three-dimensional position and velocity information anywhere in the world. Preliminary studies have been conducted to investigate differential GPS concept mechanizations and cost, and to theoretically predict navigation performance and the impact of degradation of the GPS C/A code for national security considerations. The obtained results are encouraging, but certain improvements are needed. As a second step in the program, a single-channel sequential GPS navigator was installed and operated in the NASA SH-3G helicopter. A series of flight tests were conducted. It is found that performance of the Navstar GPS Z-set is quite acceptable to support area navigation and nonprecision approach operations.

Edwards, F. G.↗
NASA NTRS1977

Flight test pilot evaluation of a delayed flap approach procedure

Using NASA's CV-990 aircraft, a delayed flap approach procedure was demonstrated to nine guest pilots from the air transport industry. Four demonstration flights and 37 approaches were conducted under VFR weather conditions. A limited pilot evaluation of the delayed flap procedure was obtained from pilot comments and from questionaires they completed. Pilot acceptability, pilot workload, and ATC compatibility were quantitatively rated. The delayed flap procedure was shown to be feasible, and suggestions for further development work were obtained.

Bull, J. S.↗
NASA NTRS1976

Delayed flap approach procedures for noise abatement and fuel conservation

The NASA/Ames Research Center is currently investigating the delayed flap approach during which pilot actions are determined and prescribed by an onboard digital computer. The onboard digital computer determines the proper timing for the deployment of the landing gear and flaps based on the existing winds and airplane gross weight. Advisory commands are displayed to the pilot. The approach is flown along the conventional ILS glide slope but is initiated at a higher airspeed and in a clean aircraft configuration that allows for low thrust and results in reduced noise and fuel consumption. Topics discussed include operational procedures, pilot acceptability of these procedures, and fuel/noise benefits resulting from flight tests and simulation.

Edwards, F. G.↗
NASA NTRS1975

Flight performance of a navigation, guidance, and control system concept for automatic approach and landing of space shuttle orbiter

Unpowered automatic approaches and landings were conducted to study navigation, guidance, and control problems associated with terminal area approach and landing for the space shuttle vehicle. The flight tests were performed in a Convair 990 aircraft equipped with a digital flight control computer connected to the aircraft control system and displays. The tests were designed to evaluate the performance of a navigation and guidance concept that utilized blended radio/inertial navigation with VOR, DME, and ILS as the ground navigation aids. Results from 36 automatic approaches and landings from 11,300 m (37,000 ft) to touchdown are presented. Preliminary results indicate that this concept may provide sufficient accuracy to accomplish automatic landing of the shuttle orbiter without air-breathing engines.

Edwards, F. G.↗
NASA NTRS1974

Flight test of an automatic approach and landing concept for a simulated space shuttle represented by the NASA Convair 990 aircraft

Unpowered automatic approaches and landings were conducted to study navigation, guidance, and control problems associated with terminal area, approach, and landing operation for the space shuttle. A Convair 990 aircraft was equipped with a digital flight-control computer connected to the aircraft control systems and displays. The flight tests evaluated, from 11,300 m to touchdown, the performance of a navigation and guidance concept that utilized blended radio/inertial navigation with VOR, DME, and ILS as the ground radio navigation aids. The results from 36 automatic approaches and landings are analyzed. Preliminary results indicate that this concept may provide sufficient accuracy that automatic landing of the unpowered shuttle orbiter can be accomplished on a conventional size runway.

Smith, D. W.↗
NASA NTRS1973

Flight test results from the CV990 simulated space shuttle during unpowered automatic approaches and landings

Unpowered automatic approaches and landings with a CV990 aircraft were conducted to study navigation, guidance, and control problems associated with terminal area approach and landing for the space shuttle. The flight tests were designed to study from 11,300 m to touchdown the performance of a navigation and guidance concept which utilized blended radio/inertial navigation using VOR, DME, and ILS as the ground navigation aids. In excess of fifty automatic approaches and landings were conducted. Preliminary results indicate that this concept may provide sufficient accuracy to accomplish automatic landing of the shuttle orbiter without air-breathing engines on a conventional size runway.

Edwards, F. G.↗
NASA NTRS1972

Determination of pilot and vehicle describing functions from the Gemini 10 mission

Three types of manual control maneuvers conducted during the Gemini-10 mission have been analyzed in order to measure and document the describing function of the pilot, the vehicle and the pilot-vehicle combination during an actual space mission. Measurements made from the data records of the reentry maneuver (a single axis control task) indicate that the pilot's control behavior changes during critical portions of the reentry. Measurements made of the deorbit maneuver and of a terminal phase initiation maneuver (three axis tasks) show that the pilot assigns priorities to the separate axes and controls them differently. His control technique is also influenced by the magnitude of the thrust disturbance present during the maneuvers. The results for all three types of maneuvers show that the pilot adapts to the nonlinear spacecraft control system in such a way that the combined pilot-vehicle dynamics take the form of the linear crossover model.

Edwards, F. G.↗