Engineering Papers⌕ Search

Engineering topics

Edgar, Alexander Steven

Publications and source records attributed to Edgar, Alexander Steven.

22 records · Page 2

Nitroplasticizer-water phase diagram

Nitroplasticizer (NP) is used in conjunction with poly(ester urethane) block co-polymer as binder material for polymer bonded explosives (PBX). Water content contributes directly to the stability of NP, poly(ester urethane), and ultimately the PBX. Therefore a n NP-water miscibility phase diagram can be an important tool in understanding potential water content in NP and further PBX processes. To determine the NP-water miscibility phase diagram, a systematic series of experiments was conducted. NP samples were saturated with water and ramped through incremental temperature steps. Aliquots were taken at each step after equilibration. Water content in NP was determined by Coulmetric Karl Fischer (KF) titration at each incremental temperature step. The sample aliquots were then analyzed by Thermogravimetric analysis (TGA), Differential Scanning Calorimetry (DSC), and Transmission Fourier Transform Infrared Spectroscopy (Near-IR). The resultant data were analyzed and combined to construct a n NP-water phase diagram. The phase diagram, ranging from 500 ppm to 5800 ppm water concentration and –90°C to 130°C, contains six distinct phases separated by five distinct phase separations.

36 MATERIALS SCIENCE↗

Characterization of Various Materials Using Refractometry

Refractive index (RI) is a fundamental physical property of a material. However, the RI values of several binders, including nitroplasticizer (NP), Estanes, and KelF/FK 800, are not available in literature. Further, their temperature dependencies are undocumented either. In this study, we have developed a set of methodologies to accurately and effectively determine the RIs of these binder materials between 20 and 70°C. The RIs of these binders without aging show linear correlations with temperature, as shown in the figure below. Among these materials, Estane 5714 has the highest RI whereas FK800 has the lowest RI. As materials age, the changes in their RIs are different, suggesting different aging behavior of these binders upon heating. Typically, NP and Estane degraded through hydrolysis give lower RIs than the baseline materials. However, when KelF/FK800 materials thermally age, their RIs increase. Overall, this study demonstrates refractometry is a sensitive technique to detect aging signs in various materials of interest.

36 MATERIALS SCIENCE↗

Creep Analysis of Poly(ester urethane) Copolymer by Dynamic Mechanical Analysis (DMA): Melt Determination

An experiment is presented utilizing film tension, creep test dynamic mechanical analysis (DMA) to characterize the physical properties of a poly(ester urethane) block copolymer, Estane ® 5703. The polymer was pressed into a sheet from pellet form and cut into strips for analysis utilizing the TA Q800 DMA with film tension clamp. The strips were tested under five constant stress analyses from 0.125 to 0.625, at 0.125 MPa increments. Each analysis was run stepwise through a temperature gradient from 25 °C to 67 .5 °C with 2.5 °C increments, the material reached the instrument maximum displacement at different temperature steps dependent on the constant applied stress. At each of the 18 temperature steps the material was held at constant stress for 10 minutes and allowed to recover under stress-less conditions for 20 minutes. With data analysis recoverable strain data was produced and ultimately a curve of Modulus at temperature, the regression extrapolated to modulus = 0 M Pa. The extrapolated point correlated with data the weighted average melt point of the polymer measured by MDSC, within the regressive least squares fit of the measured moduli. Thereby measuring the melt temperature of a polymer by DMA. This is the third in a series of three reports 4,5 on the physical properties and degradation processes of materials used in polymer bonded explosive 9501 written for submission to the University of Oregon, Masters Industrial Internship Program.

36 MATERIALS SCIENCE↗

A Modulated Differential Scanning Calorimetry Method for Characterization of Poly(ester urethane) Elastomer

A systematic series of experiments is presented utilizing MDSC to resolve the overlapping melt peaks found when analyzing poly(ester urethane) block copolymer elastomer by MDSC. Testing method parameters are idealized through diagnostic methods, leading to method parameters individualized to the material, which allow to optimize the MDSC method for the poly(ester urethane) characterization despite potentially problematic sample geometry. This is the second in a series of three reports on the degradation processes and physical properties of the materials used in polymer bonded explosive 9501.

36 MATERIALS SCIENCE↗