Engineering Papers⌕ Search

Engineering topics

Eddings, Eric

Publications and source records attributed to Eddings, Eric.

Multiphysics simulation of supercritical CO 2 gasification for hydrogen production

A bench-scale supercritical CO 2 gasifier is being considered by the U.S. Department of Energy’s National Energy Technology Laboratory (NETL). A reacting computational fluid dynamics (CFD) model was developed using ANSYS/Fluent in order to investigate the impact of various operating parameters on syngas composition. The model was validated using available data in the literature. Simulations were conducted over a range of coal-slurry loadings, reaction temperatures, system pressures, and oxygen mass flowrates with the goal of optimizing hydrogen production for the considered reactor. The results from the simulations identified a positive correlation between slurry loading and hydrogen production, while reactor temperature and pressure had a limited impact on H 2 production at the conditions of interest. Additionally, the simulations indicated that oxygen mass flowrate has less of an impact on hydrogen production at higher slurry loadings.

08 HYDROGEN↗

Multiphysics Simulation of Supercritical CO2 Gasification for Hydrogen Production

A bench-scale supercritical CO2 gasifier is being considered by the U.S. Department of Energy’s National Energy Technology Laboratory (NETL). A reacting computational fluid dynamics (CFD) model was developed using ANSYS/Fluent in order to investigate the impact of various operating parameters on syngas composition. The model was validated using available data in the literature. Simulations were conducted over a range of coal-slurry loadings, reaction temperatures, system pressures, and oxygen mass flowrates with the goal of optimizing hydrogen production for the considered reactor. The results from the simulations identified a positive correlation between slurry loading and hydrogen production, while reactor temperature and pressure had a limited impact on H2 production at the conditions of interest. Additionally, the simulations indicated that oxygen mass flowrate has less of an impact on hydrogen production at higher slurry loadings.

Prlina, Alexander↗

Effect of secondary gas-phase reactions (SGR) in pyrolysis of carbon feedstocks for anisotropic carbon materials production – 2: Effects of SGR on tars produced from varying ranks of coal

Herein, this work explores the extent to which secondary gas-phase reactions (SGR) in pyrolysis can be used to modify coal tar chemistries from coals of different ranks in favor of improved anisotropy formation in their respective pitches. Pyrolysis was performed on four different coals of varying bituminous rank (Utah Sufco, Wyoming PRB Black Thunder, Illinois #6, and West Virginia Flying Eagle), with SGR temperatures ranging from 800 to 900° C and nominal SGR gas-phase residence times from 1 to 2.5 s. The oxygen content, aliphatic content, and molecular weight distributions of the coal tar samples were measured to indicate the changes with increasing levels of SGR, and microscopy was also used to measure changes in anisotropy formation in the resulting pitch samples. Generally, for all coals tested, increased levels of pyrolysis SGR led to decreased oxygen and aliphatic content, increased molecular weight sizes, and improved anisotropy formation. However, it was clear that the extent of these property changes depended on the chemistry and rank of the starting coal feedstock. Despite the relatively high rank of the Illinois #6 coal, its respective pitch samples performed poorly in improving anisotropy formation, due to its high sulfur content. The PRB, Sufco, and Flying Eagle coals performed better in their anisotropy formation than Illinois #6, depending on their respective coal ranks. Statistical analysis (analysis of variance, ANOVA) performed on the sample characterization data also suggests that SGR temperature is consistently the most dominant and significant effect on the resulting coal products.

01 COAL, LIGNITE, AND PEAT↗

Effect of secondary gas-phase reactions (SGR) in pyrolysis of carbon feedstocks for anisotropic carbon materials production – 1: Controlling SGR to modify intermediate coal tar species to improve pitch anisotropy

To meet the increasing demand for graphitizable carbon products, such as needle coke and carbon fiber, more carbon feedstocks capable of forming anisotropy should be utilized. Non-coking coals are widely available but are not typically suitable for producing anisotropic carbons due to lacking proper coal chemistry. This work used secondary gas-phase reactions (SGR) during coal pyrolysis to improve the coal tar chemistry of a non-coking coal for anisotropic carbon production. SGR pyrolysis temperatures and residence times were varied (T = 800–900°C and τ = 0–2.5 s), and analysis of the intermediate coal tar products showed that as these SGR pyrolysis conditions increased, the oxygen and aliphatic concentrations decreased, whereas aromatic contents and molecular weights increased. Without any SGR, microscopy of the thermally-treated coal tar pitch product revealed that the coal tar pitch was isotropic; however, upon using increased SGR pyrolysis conditions, the resulting coal tar pitch samples substantially increased in the percentage and quality of anisotropy formation. Further, the products' analyses show clear trends of modified chemical properties in the intermediate coal tar and improved anisotropy results. Thus, the results presented in this work show that by controlling the SGR during pyrolysis of a non-coking coal, this approach can modify the coal tar chemistry towards a precursor more suitable for quality anisotropic carbon material production.

01 COAL, LIGNITE, AND PEAT↗

Characterization of Oxy-combustion Impacts in Existing Coal-fired Boilers

Reaction Engineering International (REI) managed a team of experts from University of Utah, Siemens Energy, Praxair, Vattenfall AB, Sandia National Laboratories, Brigham Young University (BYU) and Corrosion Management Ltd. to perform multi-scale experiments, coupled with mechanism development, process modeling and CFD modeling, for both applied and fundamental investigations. The primary objective of this program was to acquire data and develop tools to characterize and predict impacts of CO{sub 2} flue gas recycle and burner feed design on flame characteristics (burnout, NO{sub x}, SO{sub x}, mercury and fine particle emissions, heat transfer) and operational concerns (fouling, slagging and corrosion) inherent in the retrofit of existing coal-fired boilers for oxy-coal combustion. Experimental work was conducted at Sandia National Laboratories’ Entrained Flow Reactor, the University of Utah Industrial Combustion Research Facility, and Brigham Young University. Process modeling and computational fluid dynamics (CFD) modeling was performed at REI. Successful completion of the project objectives resulted in the following key deliverables: 1) Multi-scale test data from 0.1 kW bench-scale, 100 kW and 200 kW laboratory-scale, and 1 MW semi-industrial scale combustors that describe differences in flame characteristics, fouling, slagging and corrosion for coal combustion under air-firing and oxygen-firing conditions, including sensitivity to oxy-burner design and flue gas recycle composition. 2) Validated mechanisms developed from test data that describe fouling, slagging, waterwall corrosion, heat transfer, char burnout and sooting under coal oxy-combustion conditions. The mechanisms were presented in a form suitable for inclusion in CFD models or process models. 3) Principles to guide design of pilot-scale and full-scale coal oxy-firing systems and flue gas recycle configurations, such that boiler operational impacts from oxy-combustion retrofits are minimized. 4) Assessment of oxy-combustion impacts in two full-scale coal-fired utility boiler retrofits based on computational fluid dynamics (CFD) modeling of air-fired and oxygen-fired operation. This research determined that it is technically feasible to retrofit the combustion system in an air-fired boiler for oxy-fired operation. The impacts of CO{sub 2} flue gas recycle and burner design on flame characteristics (burnout, NO{sub x}, SO{sub x}, mercury and fine particle emissions, heat transfer) and operational concerns (fouling, slagging and corrosion) were minimal, with the exception of high sulfur levels resulting from untreated flue gas recycle with medium and high-sulfur coals. This work focused on combustion in the radiant and convective sections of the boiler and did not address boiler system integration issues, plant efficiencies, impacts on downstream air pollution control devices, or CO{sub 2} capture and compression. The experimental data, oxy-firing system principles and oxy-combustion process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess retrofit applications of oxy-combustion technologies to existing boilers and to guide development of new designs.

20 FOSSIL-FUELED POWER PLANTS↗

Chemical and morphological characterization of soot and soot precursors generated in an inverse diffusion flame with aromatic and aliphatic fuels

Knowledge of the chemical and physical structure of young soot and its precursors is very useful in understanding the paths leading to soot particle inception. This paper presents chemical and morphological characterization of the products generated in ethylene and benzene inverse diffusion flames (IDF) using different analytical techniques. The trend in the data indicates that the soot precursor material and soot particles generated in the benzene IDF have a higher degree of complexity than the samples obtained in the ethylene IDF, which is reflected by an increase in the aromaticity of the chloroform extracts observed by {sup 1}H NMR and FT-IR, and shape and size of soot particles obtained by TEM and HR-TEM. It is important to highlight that the soot precursor material obtained at the lower positions in the ethylene IDF has a significant contribution of aliphatic groups, which play an important role in the particle inception and mass growth processes during the early stages of soot formation. However, these groups progressively disappear in the samples taken at higher positions in the flame, due to thermal decomposition processes. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Clean Coal Program Research Activities

Although remarkable progress has been made in developing technologies for the clean and efficient utilization of coal, the biggest challenge in the utilization of coal is still the protection of the environment. Specifically, electric utilities face increasingly stringent restriction on the emissions of NO{sub x} and SO{sub x}, new mercury emission standards, and mounting pressure for the mitigation of CO{sub 2} emissions, an environmental challenge that is greater than any they have previously faced. The Utah Clean Coal Program addressed issues related to innovations for existing power plants including retrofit technologies for carbon capture and sequestration (CCS) or green field plants with CCS. The Program focused on the following areas: simulation, mercury control, oxycoal combustion, gasification, sequestration, chemical looping combustion, materials investigations and student research experiences. The goal of this program was to begin to integrate the experimental and simulation activities and to partner with NETL researchers to integrate the Program's results with those at NETL, using simulation as the vehicle for integration and innovation. The investigators also committed to training students in coal utilization technology tuned to the environmental constraints that we face in the future; to this end the Program supported approximately 12 graduate students toward the completion of their graduate degree in addition to numerous undergraduate students. With the increased importance of coal for energy independence, training of graduate and undergraduate students in the development of new technologies is critical.

01 COAL, LIGNITE, AND PEAT↗