Engineering Papers⌕ Search

Engineering topics

Dutta, S.

Publications and source records attributed to Dutta, S..

At least 37 records · Page 2

Automated selection of the optimal cardiac phase for single-beat coronary CT angiography reconstruction

Purpose: Reconstructing a low-motion cardiac phase is expected to improve coronary artery visualization in coronary computed tomography angiography (CCTA) exams. This study developed an automated algorithm for selecting the optimal cardiac phase for CCTA reconstruction. The algorithm uses prospectively gated, single-beat, multiphase data made possible by wide cone-beam imaging. The proposed algorithm differs from previous approaches because the optimal phase is identified based on vessel image quality (IQ) directly, compared to previous approaches that included motion estimation and interphase processing. Because there is no processing of interphase information, the algorithm can be applied to any sampling of image phases, making it suited for prospectively gated studies where only a subset of phases are available. Methods: An automated algorithm was developed to select the optimal phase based on quantitative IQ metrics. For each reconstructed slice at each reconstructed phase, an image quality metric was calculated based on measures of circularity and edge strength of through-plane vessels. The image quality metric was aggregated across slices, while a metric of vessel-location consistency was used to ignore slices that did not contain through-plane vessels. The algorithm performance was evaluated using two observer studies. Fourteen single-beat cardiac CT exams (Revolution CT, GE Healthcare, Chalfont St. Giles, UK) reconstructed at 2% intervals were evaluated for best systolic (1), diastolic (6), or systolic and diastolic phases (7) by three readers and the algorithm. Pairwise inter-reader and reader-algorithm agreement was evaluated using the mean absolute difference (MAD) and concordance correlation coefficient (CCC) between the reader and algorithm-selected phases. A reader-consensus best phase was determined and compared to the algorithm selected phase. In cases where the algorithm and consensus best phases differed by more than 2%, IQ was scored by three readers using a five point Likert scale. Results: There was no statistically significant difference between inter-reader and reader-algorithm agreement for either MAD or CCC metrics (p > 0.1). The algorithm phase was within 2% of the consensus phase in 15/21 of cases. The average absolute difference between consensus and algorithm best phases was 2.29% ± 2.47%, with a maximum difference of 8%. Average image quality scores for the algorithm chosen best phase were 4.01 ± 0.65 overall, 3.33 ± 1.27 for right coronary artery (RCA), 4.50 ± 0.35 for left anterior descending (LAD) artery, and 4.50 ± 0.35 for left circumflex artery (LCX). Average image quality scores for the consensus best phase were 4.11 ± 0.54 overall, 3.44 ± 1.03 for RCA, 4.39 ± 0.39 for LAD, and 4.50 ± 0.18 for LCX. There was no statistically significant difference (p > 0.1) between the image quality scores of the algorithm phase and the consensus phase. Conclusions: The proposed algorithm was statistically equivalent to a reader in selecting an optimal cardiac phase for CCTA exams. When reader and algorithm phases differed by >2%, image quality as rated by blinded readers was statistically equivalent. By detecting the optimal phase for CCTA reconstruction, the proposed algorithm is expected to improve coronary artery visualization in CCTA exams.

61 RADIATION PROTECTION AND DOSIMETRY↗

Logic circuit prototypes for three-terminal magnetic tunnel junctions with mobile domain walls

Spintronic computing promises superior energy efficiency and nonvolatility compared to conventional field-effect transistor logic. But, it has proven difficult to realize spintronic circuits with a versatile, scalable device design that is adaptable to emerging material physics. Here we present prototypes of a logic device that encode information in the position of a magnetic domain wall in a ferromagnetic wire. We show that a single three-terminal device can perform inverter and buffer operations. We demonstrate one device can drive two subsequent gates and logic propagation in a circuit of three inverters. This prototype demonstration shows that magnetic domain wall logic devices have the necessary characteristics for future computing, including nonlinearity, gain, cascadability, and room temperature operation.

42 ENGINEERING↗

Precise energy eigenvalues of hydrogen-like ion moving in quantum plasmas

The analytic form of the electrostatic potential felt by a slowly moving test charge in quantum plasma is developed. It has been shown that the electrostatic potential is composed of two parts: the Debye-Huckel screening term and the near-field wake potential. The latter depends on the velocity of the test charge as well as on the number density of the plasma electrons. Rayleigh-Ritz variational calculation has been done to estimate precise energy eigenvalues of hydrogen-like carbon ion under such plasma environment. A detailed analysis shows that the energy levels gradually move to the continuum with increasing plasma electron density while the level crossing phenomenon has been observed with the variation of ion velocity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Defect correlated fluorescent quenching and electron phonon coupling in the spectral transition of Eu{sup 3+} in CaTiO{sub 3} for red emission in display application

This paper reports on the defect correlated self-quenching and spectroscopic investigation of calcium titanate (CaTiO{sub 3}) phosphors. A series of CaTiO{sub 3} phosphors doped with trivalent europium (Eu{sup 3+}) and codoped with potassium (K{sup +}) ions were prepared by the solid state reaction method. The X-ray diffraction results revealed that the obtained powder phosphors consisted out of a single-phase orthorhombic structure and it also indicated that the incorporation of the dopants/co-dopants did not affect the crystal structure. The scanning electron microscopy images revealed the irregular morphology of the prepared phosphors consisting out of μm sized diameter particles. The Eu{sup 3+} doped phosphors illuminated with ultraviolet light showed the characteristic red luminescence corresponding to the {sup 5}D{sub 0}→{sup 7}F{sub J} transitions of Eu{sup 3+}. As a charge compensator, K{sup +} ions were incorporated into the CaTiO{sub 3}:Eu{sup 3+} phosphors, which enhanced the photoluminescence (PL) intensities depending on the doping concentration of K{sup +}. The concentration quenching of Eu{sup 3+} in this host is discussed in the light of ion-ion interaction, electron phonon coupling, and defect to ion energy transfer. The spectral characteristics and the Eu-O ligand behaviour were determined using the Judd-Ofelt theory from the PL spectra instead of the absorption spectra. The CIE (International Commission on Illumination) parameters were calculated using spectral energy distribution functions and McCamy's empirical formula. Photometric characterization indicated the suitability of K{sup +} compensated the CaTiO{sub 3}:Eu{sup 3+} phosphor for pure red emission in light-emitting diode applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Frequency-offset insensitive digital modem techniques

Conventional DPSK systems are adversely affected by transmitter/receiver frequency offsets due to frequency reference errors and Doppler shifts. Two DPSK modem concepts are presented which avoid the long frequency acquisition process of conventional DPSK. One technique involves a modified demodulator for conventional DPSK signals, while the other involves making minor changes to both the modulator and demodulator. Simulation results are provided showing performance relative to conventional DPSK.

Dutta, S.↗

Metalizing Solar Cells by Selective Electroplating

Contact patterns traced by laser scanning. Conductor paths deposited on silicon solar-cell wafers by laser irradiation followed by electroplating. Laser-assisted metalization technique offers better resolution and lower contact resistance than does conventional metalization by screen printing. At the same time, less expensive than metalization with masks and photolithography.

Dutta, S.↗

Si3N4-Based Ceramic With Greater Hot Strength

Zyttrite-doped material outperforms MgO-doped material above 1,200 degrees C. New ceramic material produced by addition of 10 weight percent zyttrite (yttria-stabilized zirconia) to (silicon nitride) offers significantly-improved high-temperature properties (those of MgO-doped Si3N4 ceramic). Work also showed that controlled Si3N4 powder with 10 weight percent zyttrite, significant improvement in room-temperature strength achieved. Variety of high-temperature structural applications are silicon nitride and silicon carbide. Potential for use in aircraft and automobile engines and in electric-power generating systems. Improved properties strongly suggest that the 10-weight percent zyttrite/Si3N4 material has strong potential for high-temperature applications.

Dutta, S.↗

Densification and properties of alpha-silicon carbide

The sintering behavior of alpha-SiC with B and C sintering aids and without sintering aids was investigated experimentally. The sintering was performed for 30-60 min in argon flow at 2150 and 2200 C. The density of the sintered bars was determined by weighing and measuring the bars, four-point flexure tests were conducted on machined bars, and the Weibull modulus was determined by regression analysis. It is found that type 1 alpha-SiC powder, which does not densify, can be sintered to a high final density (in excess of 96 percent of the theoretical value) using B and C sintering aids. Flexure test results and Weibull modulus data suggest that the strength of the alpha-SiC ceramic is greatly affected by processing flaws and also by inclusions and machining flaws.

Dutta, S.↗

The feasibility of silicon on garnet technology

The feasibility of combining silicon and magnetic bubble technologies is demonstrated. Functional MOSFETs have been fabricated on top of bubble films coated with 1-micron thick SiO2 layers. The large grain silicon necessary for these devices is obtained by laser recrystallization of polycrystalline silicon (polysilicon). The laser-recrystallization process causes changes in the magnetic properties of the bubble film; however, these changes can be reversed by subsequent thermal anneals. The required temperature treatments after laser annealing are compatible with the MOSFET fabrication process.

Rasky, P. H. L.↗

Laser-assisted solar-cell metallization processing

A photolytic metal deposition system using a focused continuous wave ultraviolet laser, a photolytic metal deposition system using a mask and ultraviolet flood illumination, and a pyrolytic metal deposition system using a focused continuous wave laser were studied. Fabrication of solar cells, as well as characterization to determine the effects of transient heat on solar cell junctions were investigated.

Dutta, S.↗

Laser-assisted solar cell metallization processing

Laser assisted processing techniques utilized to produce the fine line, thin metal grid structures that are required to fabricate high efficiency solar cells are investigated. The tasks comprising these investigations are summarized. Metal deposition experiments are carried out utilizing laser assisted pyrolysis of a variety of metal bearing polymer films and metalloorganic inks spun onto silicon substrates. Laser decomposition of spun on silver neodecanoate ink yields very promising results. Solar cell comb metallization patterns are written using this technique.

Dutta, S.↗

Sinterability, strength and oxidation of alpha silicon carbide powders

An investigation is made of pressureless sintering of commercially available alpha-SiC powders at temperatures between 1900 and 2150 C for periods of 10 to 240 min under one atmosphere of argon pressure. It is found that alpha-SiC powder containing boron and carbon sintering aids is sinterable at 2150 C for a period of 30 min to a high final density (greater than 96 percent of theoretical). In alpha-SiC powder containing aluminum and carbon sintering aids, the final density achieved is only about 80 percent of theoretical. Determinations are made of room temperature and high temperature (1370 C) flexure strength and oxidation resistance on sintered high density (more than 96 percent of theoretical) alpha-SiC (boron, carbon) material. It is found that both the strength and the resistance to oxidation are equivalent and comparable to those of the sintered alpha-SiC which represents the state of the art.

Dutta, S.↗

Microstructure, strength, and oxidation of a 10 wt pct zyttrite-Si3N4 ceramic

Hot pressed Si3N4 doped with 10 wt pct zyttrite as a sintering aid was studied. An equiaxed, fine grained microstructure was predominant, with no apparent porosity. Bend strengths were determined at room temperature and high temperatures (up to 1370 C). Oxidation was measured by weight gain at 1370 C in air. The resulting material exhibited very good room temperature strength (755 MPa). The work showed that room temperature strength can be improved significantly by using controlled Si3N4 powder with 10 wt pct zyttrite. High temperature strength (514 MPa) at 1370 C was nearly double that of hot-pressed Si3N4 (NC-132). The oxidation resistance at 1370 C was also higher than that of NC-132.

Dutta, S.↗

Laser-assisted solar cell metallization processing

Laser-assisted processing techniques utilized to produce the fine line, thin metal grid structures that are required to fabricate high efficiency solar cells are examined. Two basic techniques for metal deposition are investigated; (1) photochemical decomposition of liquid or gas phase organometallic compounds utilizing either a focused, CW ultraviolet laser (System 1) or a mask and ultraviolet flood illumination, such as that provided by a repetitively pulsed, defocused excimer laser (System 2), for pattern definition, and (2) thermal deposition of metals from organometallic solutions or vapors utilizing a focused, CW laser beam as a local heat source to draw the metallization pattern.

Dutta, S.↗

Laser assisted deposition

Applications of laser-based processing techniques to solar cell metallization are discussed. Laser-assisted thermal or photolytic maskless deposition from organometallic vapors or solutions may provide a viable alternative to photovoltaic metallization systems currently in use. High power, defocused excimer lasers may be used in conjunction with masks as an alternative to direct laser writing to provide higher throughput. Repeated pulsing with excimer lasers may eliminate the need for secondary plating techniques for metal film buildup. A comparison between the thermal and photochemical deposition processes is made.

Dutta, S.↗

Compositional effects on Si3N4 fracture surfaces

Surface analysis techniques (X-ray, infrared reflection spectroscopy, Auger electron spectroscopy) applied to the same samples reveal that fracture surfaces of Si3N4 with Y2O3 densification aids possess a higher concentration of oxygen than the bulk. The oxide densification aids thus concentrate in the grain boundaries, and even low-temperature fracture is seen as occurring preferentially within the oxygen-enriched grain boundaries. It is found that increasing the concentrations of Y2O3 and Al2O3 increases the oxygen content of the fracture surface. A range of 13-15 percent Y2O3 + 6 percent Al2O3 gives an amorphous grain-boundary phase that is resistant to devitrification. Fracture occurs through the amorphous phase, and heat treatment at 1000 C has little effect on the amorphous phase.

Hench, L. L.↗