Engineering topics

Dufrane, K. F.

Publications and source records attributed to Dufrane, K. F..

At least 19 records

NASA NTRS1991

Lubricant Selection Manual, Phase 3

Future spacecraft must be designated to operate for very long time periods in space. For example, a target goal for the Space Station is 30 years of operation. Although the actual life may be significantly less than this optimistic goal, the life will certainly be a critical issue in design. The bearings on primary components such as the alpha and beta joints must obviously be designed and lubricated with the objective of optimum performance life. In addition to these joints, there will be numerous other tribological (rubbing or rolling) interfaced that will be required to function for the life of the spacecraft. A major key to adequate performance of tribological interface is proper lubrication. Lubricants can be divided into two basic classes: solid films and liquids. Both types have been used extensively in space applications. Both have advantages and disadvantages that must be carefully considered in their selection. The purpose here is to summarize selection criteria for liquid and solid lubricants applied to long-life spacecraft.

Kannel, J. W.↗

NASA NTRS1990

Space Station long term lubrication analysis. Phase 1 preliminary tribological survey

Increases in the size, complexity, and life requirements of satellites and space vehicles have put increasing demands on the lubrication requirements for trouble-free service. Since the development costs of large systems are high, long lives with minimum maintenance are dictated. The Space Station represents the latest level of size and complexity in satellite development; it will be nearly 100 meters in major dimensions and will have a life requirement of thirty years. It will have numerous mechanisms critical to its success, some of which will be exposed to the space environment. Designing long-life lubrication systems and choosing appropriate lubricants for these systems will be necessary for their meeting the requirements and for avoiding failures with associated dependent mechanisms. The purpose of this program was to identify the various critical mechanisms and review their designs during the overall design and development stage so that problem areas could be avoided or minimized prior to the fabrication of hardware. The specific objectives were fourfold: (1) to perform a tribology survey of the Space Station for the purpose of documenting each wear point as to materials involved, environmental conditions, and operating characteristics; (2) to review each wear point (point of relative motion) as to the lubrication used and substrate materials selected in the context of its operating characteristics and the environmental conditions imposed; (3) to make recommendations for improvement in areas where the lubricant chosen and/or where the substrate (materials of the wear couple) are not considered optimum for the application; and (4) to make or recommend simulated or full scale tests in tribological areas where the state-of-the-art is being advanced, in areas where new designs are obviously being employed and a critical review would indicate that problems are a strong possibility, and/or where excessive wear, a malfunction, or excessive leakage would create fluid systems problems or contamination of exposed optical equipment.

Dufrane, K. F.↗

NASA NTRS1988

Transfer Lubrication For Cryogenic Bearings

Report presents evaluation of bronze-filled polytetrafluoroethylene (PTFE), known as Salox M, as cage material for ball bearings in high-pressure turbopumps for liquid oxygen. Material evaluated as potentially longer-lived replacement for glass-filled PTFE, known as Armalon. Cage transfers PTFE to balls to form solid lubricant film. However, glass fibers in glass-filled material tend to interfere with transfer. Two cage-design concepts developed; one involves metal-reinforced cage of bronze-filled PTFE; other calls for bronze-filled PTFE inserts in metal structure.

Barber, S. A.↗

NASA NTRS1986

Evaluation of transfer films of Salox M on 440C for HPOTP bearing cage applications, task 119

The objective of the task was to evaluate the suitability of a bronze-filled polytetra fluoroethylene (Salox M) as the cage material in Space Shuttle Main Engine (SSME) high pressure oxygen turbo pump (HPOTP) bearings. The role of the cage pocket material will be to provide a transferred lubricating interface at the ball-race contact region. A series of experiments was conducted which involved block-on-ring tests (the block was the polytetrafluoroethylene (PTFE) -filled material and the ring was through-hardened 440C steel) and high speed traction tests of two 440C disks with one disk rubbed with a PTFE block to generate a transfer film. Measurements included post test visual observations of the condition of the 440C, wear rate measurements of the blocks, and traction measurements between the disks. It was observed that both Salox M and glass-filled PTFE (Armalon) transferred PTFE to 440C at cryogenic temperatures. Bronze is also transferred to uncoated 440C from the Salox M. At room temperature no PTFE transfer was observed in the high speed disk tests due to severe frictional heating, although bronze transfer still occurred with the bronze-PTFE Salox M material. Since the bearing will operate at cryogenic temperature, transfer films are very probable. Salox M wore slightly, although probably tolerably, more than glass-filled PTFE against 440C. However, Salox M is clearly less abrasive to 440C than is the glass-filled material. When the surface layer of PTFE is depleted from the glass-filled material, the glass fibers tend to seriously abrade the steel. This problem does not occur with Salox M. The surface roughness studies indicate that smooth balls are quite reasonable for transfer films. No significant difference in wear rates of the candidate cage materials was observed when the 440C surface finish was increased from 0.025 micron to 0.1 micron cla. At higher levels of roughness, the wear rate increased. Two surface coatings (MoS2 and TiN) were tested. The surface coatings tended to reduce the Salox M wear rate and reduce bronze transfer. PTFE transfer at cryogenic temperatures still occurred with the surface coatings. Two cage design concepts are presented utilizing Salox M material. One design involves a metal-reinforced Salox M cage, while the second design uses Salox M inserts in a metal structure.

Barber, S. A.↗

NASA NTRS1986

Rolling element bearings in space

Some of the advances in tribology that have been associated with aerospace mechanisms are discussed. The needs of aerospace have been the dominant forces leading to improvements in understanding and applying tribology technology. In the past two decades improvements in understanding bearing torque, elastohydrodynamic lubrication, lubricant distribution, cage stability, and transfer film lubricants have been made. It is anticipated that further developments will be made in response to future aerospace requirements.

Kannel, J. W.↗

NASA NTRS1985

Investigation of instability, dynamic forces, and effect of dynamic loading on strength of cages for the bearings in the high pressure oxygen turbopumps for the space shuttle main engine

Experiments were performed to determine the effect of cyclic loading on bearing cage strength. A long term working tensile load of approximately 1300 N (300 lbs) was found to be the likely maximum. Higher loads caused a decrease in cage tensile strength after the 125,000 cycle testing period. Poisson's ratio in compression was found to be highly dependent upon the direction of the fiberglass plies. At room temperature the value was 0.15 with the plies and 0.68 across the plies. At -196 C (-321 F), the value with the plies was 0.20. The results of the analyses conducted have again demonstrated the critical need for improved lubrication in the high pressure oxygen turbopump bearings. Lubricant films with low shear strength and low friction coefficients promote cage stability and decrease ball/cage forces during marginal operating conditions. The analysis of the effect of combined bearing loads on ball/cage loads has identified a radial load of 3600 N (800 lbs) as the maximum for the current clearance of the balls and cage pockets. Liquid oxygen impinging on the cage in the direction of rotation was found to enhance cage stability.

Dufrane, K. F.↗

NASA NTRS1985

Evaluation of load tracks and wear of two sets of bearings from space shuttle main engine high pressure oxygen turbopumps

Bearings supporting the rotor in the High Pressure Oxygen Turbopump (HPOTP) were examined. The No. 1 bearings from both units were in good condition and had successfully completed 5000 seconds of operation. The No. 2 bearings, which were in service the same length of time, were significantly degraded in the form of ball wear, race pitting, and damage from high axial loads. The No. 3 and 4 bearings were in generally acceptable condition. The general conclusion from the examinations was that improved cooling on the No. 2 bearings and further improvements in controlling axial and radial load would likely result in the HPOTP meeting the qualification test results.

Kannel, J. W.↗

NASA NTRS1985

Space station long-term lubrication analysis

The objectives of this program are: (1) to perform a complete tribology survey of every point of contact in the space station subject to relative motion regarding the materials, environment, and operation characteristics, (2) to review each point of relative motion regarding the selected materials and lubricants from the standpoint of the required operating characteristics and environmental conditions, (3) to make recommendations for improvements where the lubricants and/or materials are not considered optimum, and (4) to perform or recommend simulated or full-scale tests on components where problems are possible or likely because of new designs, significant design extensions beyond current practice, or sensitivity of other components to problems with a particular point of contact. The project is to be conducted over a 3-year time frame in two phases. Phase 1 will be a preliminary analysis conducted during the preliminary design phases of the Space Station. Phase 2 will be a more detailed analysis conducted during the period when the design becomes more established.

Dufrane, K. F.↗

NASA NTRS1984

Review of LOX Bearing and Seal Materials Tester (BSMT) radial load system

Problems concerning the bearings in the high pressure oxygen turbopumps (HPOTP) were investigated. The tasks involved: failure analyses, bearing dynamics calculations, lubrication studies, wear studies, and analyses of thermal transients. The radial load system on MSFC's bearing and seal tester used to study components for the HPOTP in liquid oxygen (LOX) is analyzed and the wear behavior of AISI 440C steel with polytetrafluoroethylene (PTFE) lubrication is studied.

Dufrane, K. F.↗

NASA NTRS1984

Measurements of elastohydrodynamic film thickness, wear and tempering behavior of high pressure oxygen turbopump bearings

The reusable design of the Space Shuttle requires a target life of 7.5 hours for the turbopumps of the Space Shuttle main engine (SSME). This large increase from the few hundred seconds required in single-use rockets has caused various problems with the bearings of the turbopumps. The berings of the high pressure oxygen turbopump (HPOTP) were of particular concern because of wear, spalling, and cage failures at service time well below the required 7.5 hours. Lubrication and wear data were developed for the bearings. Since the HPOTP bearings operate in liquid oxygen, conventional liquid lubricants cannot be applied. Therefore, solid lubricant coatings and lubricant transfer from the polytetrafluorethylene (FTFE) cage were the primary lubrication approaches for the bearings. Measurements were made using liquid nitrogen in a rolling disk machine to determine whether usable elastohydrodynamic films could be generated to assist in the bearing lubrication.

Dufrane, K. F.↗

NASA NTRS1983

Evaluation of feasibility of measuring EHD film thickness associated with cryogenic fluids

The feasibility of measuring elastohydrodynamic (EHD) films as formed with a cryogenic (LN2) fluid is evaluated. Modifications were made to an existing twin disk EHD apparatus to allow for disk lubrication with liquid nitrogen. This disk apparatus is equipped with an X-ray system for measuring the thickness of any lubricant film that is formed between the disks. Several film thickness experiments were conducted with the apparatus which indicate that good lubrication films are filmed with LN2. In addition to the film thickness studies, failure analyses of three bearings were conducted. The HPOTP turbine end bearings had experienced axial loads of 36,000 to 44,000 N (8,000 to 10,000 lb). High continuous radial loads were also experienced, which were most likely caused by thermal growth of the inner race. The resulting high internal loads caused race spalling and ball wear to occur.

Kannel, J. W.↗

NASA NTRS1983

Evaluation of outer race tilt and lubrication on ball wear and SSME bearing life reductions

Several aspects of the SSME bearing operation were evaluated. The possibility of elastohydrodynamics (EHD) lubrication with a cryogenic fluid was analyzed. Films as thick as .61 microns were predicted with one theory which may be thick enough to provide hydrodynamic support. The film formation, however, is heavily dependent on good surface finish and a low bulk bearing temperature. Bearing dynamics to determine if the radial stiffness of a bearing which are dependent on bearing misalignment were analyzed. Four ball tests were conducted at several environmental conditions from an LN2 bath to 426 C in air. Surface coatings and ball materials are evaluated. Severe wear and high friction are measured for all ball materials except when the balls have surface lubricant coatings.

Kannel, J. W.↗

NASA NTRS1981

Study of methods for applying and enhancing transfer film coatings of polytetrafluoroethylene (PTEE) to Space Shuttle Main Engine (SSME) High Pressure Oxygen Turbo Pump (HPOTP) bearings

Machines were constructed and evaluated for burnishing polytetrafluoroethylene on balls for use in the high pressure oxygen turbopump (HPOTP). The most positive performance was obtained with single-ball burnishing, but one technique for burnishing three balls simultaneously holds promise. Evaluations of the coatings in a HPOTP bearing of earlier design (employed smaller diameter balls) showed very little life enhancement before high torque and ball and race wear initiated. Other coating techniques, such as molybdenum disulfide combined with PTFE transfer films, hold promise for providing the more durable quantities of solid lubricant needed for the bearings.

Kannel, J. W.↗

NASA NTRS1981

Transfer film evaluation for shuttle engine turbopump bearing

A series of low speed experiments to evaluate the possible occurrence of transfer film lubrication and the effectiveness of burnished films in the shuttle spacecraft main engine thrust bearings were conducted. No evidence of transfer film lubrication was evident, although this could have been the result of the (used) condition of the bearing. Burnished films of either Teflon or Rulon were found to greatly enhance the performance of the bearing. Crush load experiments indicated that the bearing ultimate load capability is on the order of 489,000 N (110,000 pounds). The effect of ball (as well as race) burnishing techniques on bearing performance, different types of burnished films, and transfer film formation are suggested for further study.

Kannel, J. W.↗

NASA NTRS1980

Evaluation of axial lock-up of space shuttle main engine bearings from high pressure oxygen turbopump

The mainshaft support bearings of long life turbopumps for use on the space shuttle were evaluated to determine possible causes of failure. Specific aspects examined include the sensitivity of 15 degree versus 25 degree contact angle bearings with regard to heat damage and thermal runaway, the L/D aspects of the turbine end bearing pair with regard to hang-up due to cocking, the hang-up required to support a 44.5 KN axial load without cartridge slipping, the outer race growth as a result of a 44.5 KN axial load, and bearing torque as a function of axial load. Results indicate that hang-up of the cartridge due to bearing heating is a serious problem especially if poor lubrication of the bearing occurs and that race growth due to axial load can contribute to cartridge lock-up. The experimental evaluation of bearing performance under axial loads indicates that the bearing torque is a strong function of surface lubrication.

Kannel, J. W.↗

NASA NTRS1980

Evaluation of space shuttle main engine bearings from high pressure oxygen turbopump 9008

Two used turbopump mainshaft support bearings were examined to determine steps needed to achieve turbopump lifetimes of 27,000 seconds. The two bearings, which had been run in a high pressure oxygen turbopump, are angular contact ball bearings, applied as a preloaded pair, locked to the shaft, inner race rotating, with the outer races unrestrained axially. Examination showed that both bearings had been subjected to overloads, leading to fatigue spalling on the races and balls and advanced retainer wear. This is clear evidence of unintended high internal loads in the high pressure oxygen pump which would lead to complete bearing failure and extensive secondary pump damage. Action must be taken to reduce the applied bearing loads or to incorporate bearings of sufficient size to withstand the high loads.

Dufrane, K. F.↗

NASA NTRS1979

Evaluation of SSME high pressure liquid oxygen turbopump bearings

Examination of the bearings produced conclusive evidence that a very high axial load was applied to bearing 8517903 during a significant portion of the service time. The high loads caused serious ball and race wear and surface fatigue pitting. In all likelihood, continued operation of this bearing with the high axial load would have caused increasing deterioration and catastrophic failure. In contrast, bearing 8517900 showed much less deterioration and probably had experienced only the axial loads deliberately applied by the preload spring. Bearing 8517900 represents the best-case operation with the loads controlled to the levels intended in the design. Fatigue life calculations on bearing 8517903 with an axial load of 27,000 N showed the intolerance of the bearing to such load levels.

Dufrane, K. F.↗

NASA NTRS1978

Evaluation of worn SSME low pressure liquid oxygen turbopump bearing

The larger of two ball bearings used to support the rotor of the low pressure liquid oxygen turbopump in each of the shuttle main engines was analyzed to identify the cause of severe internal wear. The actual operating loads were calculated along with their direction and length of time at each load based on the size and location of the race contact paths. It is suggested that the engine component design be modified to reduce bearing stress and enhance lubrication.

Dufrane, K. F.↗