Engineering topics

Downing, D. R.

Publications and source records attributed to Downing, D. R..

15 records

NASA NTRS1986

Development of a takeoff performance monitoring system

The development and testing of a real-time takeoff performance monitoring system is discussed. The algorithm is madeup of two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate schedule performance data for that takeoff. The real-time segment uses the scheduled performance data generated in the pretakeoff segment, runway length data, and measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. An important feature of this algorithm is the one-time estimation of the runway rolling friction coefficient. The algorithm was tested using a six degree of freedom airplane model in a computer simulation. Results from a series of sensitivity analysis are also included.

Srivatsan, R.↗

NASA NTRS1985

Development of a sensitivity analysis technique for multiloop flight control systems

This report presents the development and application of a sensitivity analysis technique for multiloop flight control systems. This analysis yields very useful information on the sensitivity of the relative-stability criteria of the control system, with variations or uncertainties in the system and controller elements. The sensitivity analysis technique developed is based on the computation of the singular values and singular-value gradients of a feedback-control system. The method is applicable to single-input/single-output as well as multiloop continuous-control systems. Application to sampled-data systems is also explored. The sensitivity analysis technique was applied to a continuous yaw/roll damper stability augmentation system of a typical business jet, and the results show that the analysis is very useful in determining the system elements which have the largest effect on the relative stability of the closed-loop system. As a secondary product of the research reported here, the relative stability criteria based on the concept of singular values were explored.

Vaillard, A. H.↗

NASA NTRS1984

Design of a digital ride quality augmentation system for commuter aircraft

Commuter aircraft typically have low wing loadings, and fly at low altitudes, and so they are susceptible to undesirable accelerations caused by random atmospheric turbulence. Larger commercial aircraft typically have higher wing loadings and fly at altitudes where the turbulence level is lower, and so they provide smoother rides. This project was initiated based on the goal of making the ride of the commuter aircraft as smooth as the ride experienced on the major commercial airliners. The objectives of this project were to design a digital, longitudinal mode ride quality augmentation system (RQAS) for a commuter aircraft, and to investigate the effect of selected parameters on those designs.

Hammond, T. A.↗

NASA NTRS1984

Design of a digital ride quality augmentation system for a commuter aircraft

Commuter aircraft with low wing loading that operate at low altitudes are particularly susceptible to unwanted accelerations caused by atmospheric gusts. This paper describes the design and analysis of a longitudinal digital Ride Quality Augmentation System (RQAS). The RQAS designs were conducted for a Cessna 402B aircraft using the flaps and the elevator as the control surfaces. The designs are generated using linear quadratic Gaussian theory and analyzed in both the time and frequency domains. Nominal designs are presented at five flight conditions that cover a total mission. Trade-off studies are conducted to investigate the effect of sample time, computational delay time, servo bandwidth and control power.

Hammond, T. A.↗

NASA NTRS1983

Pilot controls and SPIRF flight

A study was performed to determine the relative advantages and disadvantages of four candidate pilot control devices for use by a single pilot flying a general aviation aircraft in instrument meteorological conditions. Only the pitch and roll axes were considered. The control devices examined were the wheel-yoke, center-stick, Brolley handles, and side-arm controller. Qualitative evaluation criteria were established that included instrument panel visibility, control sensitivity, pilot comfort, and space requirement behind the instrument panel. The results of the study indicated that the side-arm controller offered the possibility of an improvement, but further research was necessary to determine its feasibility.

Downing, D. R.↗

NASA NTRS1983

Restructurable Controls Problem Definition and Future Research

Restructurable controls, failure classification, airframe design, failure type, control system type, post failure mission, plant identification, controller design techniques, and restructurable control concept validation tools are considered.

Downing, D. R.↗

NASA NTRS1983

Ride quality systems for commuter aircraft

The state-of-the-art in Active Ride Augmentation, specifically in terms of its feasibility for commuter aircraft applications. A literature survey was done, and the principal results are presented here through discussion of different Ride Quality Augmentation System (RQAS) designs and advances in related technologies. Recommended follow-on research areas are discussed, and a preliminary RQAS configuration for detailed design and development is proposed.

Downing, D. R.↗

NASA NTRS1983

Design and flight testing of a digital landing approach autopilot

An important feature in General Aviation (GA) autopilots is the ability to intercept and hold the glideslope and localizer during a landing approach. Most General Aviation landing approach autopilots available today use analog systems. This paper presents the designs of digital landing approach autopilots for a General Aviation (NAVION) aircraft using modern linear quadratic control theory. Each constant gain, direct digitally designed autopilot operates synchronously at a slow rate (10 samples per second) and has modest memory requirements, i.e., a full state Kalman filter is not used. The autopilot is designed to track desired position trajectories constructed in an ILS or MLS terminal area using command generators. Alternative command errors for intercepting and holding the localizer beam centerline are investigated. Linear simulations and flight test results are presented demonstrating the successful application of the linear quadratic regulator approach.

Broussard, J. R.↗

NASA NTRS1982

Design and flight testing of a digital optimal control general aviation autopilot

This paper presents the designs of Proportional-Integral-Filter (PIF) autopilots for a General Aviation (NAVION) aircraft. The PIF autopilots use modern control theory to determine heading select and altitude select and hold autopilot modes. The PIF control law uses typical General Aviation sensors for state feedback; command error integration for command tracking; digital complimentary filtering and analog prefiltering for sensor noise suppression; a control filter for computation delay accommodation; and the incremental form to eliminate trim values in implementation. Theoretical developments for the control law are described which combine the sampled-data regulator with command generator tracking for use as a digital flight control system. The digital PIF autopilots are evaluated using closed-loop eigenvalues and simulations. Successful flight test results for the PIF autopilots are presented for different turbulence conditions and quadratic weights.

Broussard, J. R.↗

NASA NTRS1981

Flight test evaluation of advanced symbology for general aviation approach to landing displays

This paper describes a set of flight test experiments which were designed to evaluate the relative utility of candidate displays with advanced symbology for General Aviation IFR operations in the terminal area. This symbology was previously evaluated as part of the NASA Langley Research Center's Terminal Configured Vehicle Program for use in commercial airlines. The advanced symbology included vehicle track-angle, flight path angle and a perspective representation of the runway. These symbols were selectively drawn on a CRT display along with the roll attitude, pitch attitude, localizer-deviation and glideslope deviation. In addition to the CRT display, the instrument panel contained standard turn and bank, altimeter, rate of climb, airspeed, heading and engine instruments. The symbology was evaluated using tracking performance and pilot subjective ratings for an ILS capture and tracking task.

Downing, D. R.↗

NASA NTRS1979

Flight test evaluation of a digital controller used in a VTOL automatic approach and landing system

As part of the NASA Langley Research Center's effort to develop technology for VTOL operation in the air transportation system in the late 1980's and beyond, research has been conducted aimed at developing digital controller design procedures. This paper describes the verification of one design procedure by the flight evaluation of an advanced digital control algorithm. The control algorithm, operating at 10 iterations per second, follows step guidance commands with zero steady state error and thus provides an autotrim capability for the nonlinear vehicle. Changes in vehicle dynamics are accounted for using a gain scheduling technique. This control algorithm is combined with sensor filters, a trajectory generator, and a closed loop guidance algorithm to form a VTOL autoland system. A CH-47 tandem rotor helicopter which contains a set of sensors, onboard digital flight computers and electro-hydraulic actuators is used in the evaluation. All software, except input-output routines, is coded in FORTRAN using floating point arithmetic and executed in the flight computer. This autoland system is exercised by automatically flying straight-in descending decelerating trajectories typical of VFR manual approaches to a predetermined landing pad.

Downing, D. R.↗

NASA NTRS1979

NASA/Princeton digital avionics flight test facility

This paper describes a general-aviation digital avionics flight-test facility being jointly developed by the Flight Dynamics Laboratory of Princeton University and NASA/Langley Research Center. This facility consists of the Princeton avionics research aircraft (ARA) and NASA/Langley's digital avionics research (DARE) system. The ARA is a fully instrumented five-degree-of-freedom fly-by-wire aircraft. The DARE system contains a state-of-the-art flight computer system and receiving equipment that permits use of the NASA/Wallops Flight Center's position-tracking ground-based display-generation and ground-to-air digital-data-link equipment. The DARE/ARA system will be used for flight evaluation of advanced control, guidance, and display concepts developed as part of NASA/Langley Research Center's general aviation terminal area operations program.

Downing, D. R.↗

NASA NTRS1979

A real-time simulation facility for advanced digital guidance and control system research

A real-time simulation facility built at NASA's Langley Research Center to support digital guidance and control research and development activities is examined. The unit has recently been used to develop autoland systems for VTOL. The paper describes the autoland experiment and the flight environment, the simulation facility hardware and software, and presents typical simulation data to illustrate the type of data analysis carried out during software development. Finally, flight data for a later version of the autoland system are presented to demonstrate the simulation's capability to predict overall system behavior.

Bryant, W. H.↗

NASA NTRS1979

Flight test of a VTOL digital autoland system along complex trajectories

The objective of this research is the development and flight test of a digital multi-rate VTOL autoland system. This autoland system provided the NASA/Army Fly-by-Wire CH-47 helicopter with an automatic 4-D trajectory following and landing capability. Flight tests were conducted along complex trajectories with descending, turning, and decelerating segments. The flight software consists of a trajectory generator and guidance algorithm operating at two iterations per second and a set of sensor filters and an advanced controller operating at 10 iterations per second. This low iteration rate digital controller has a proportional-integral structure that provides an autotrim function. The control gains, scheduled as a function of flight condition, are updated every two seconds. All flight software, except input/output routines, are coded in FORTRAN using floating point arithmetic and are exercised in a ROLM 1664 flight computer. The flight software, the ground and flight hardware, the autoland system's position tracking performance, and the controller's velocity and heading tracking performance are presented.

Downing, D. R.↗

NASA NTRS1976

A technique using a nonlinear helicopter model for determining trims and derivatives

A technique is described for determining the trims and quasi-static derivatives of a flight vehicle for use in a linear perturbation model; both the coupled and uncoupled forms of the linear perturbation model are included. Since this technique requires a nonlinear vehicle model, detailed equations with constants and nonlinear functions for the CH-47B tandem rotor helicopter are presented. Tables of trims and derivatives are included for airspeeds between -40 and 160 knots and rates of descent between + or - 10.16 m/sec (+ or - 200 ft/min). As a verification, the calculated and referenced values of comparable trims, derivatives, and linear model poles are shown to have acceptable agreement.

Ostroff, A. J.↗