Engineering topics

Douglas, C.

Publications and source records attributed to Douglas, C..

7 records

NASA NTRS1993

The carbon components in SNC meteorites of feldspathic harzburgite composition

Two meteorites collected in Antarctica, ALH A77005 and LEW 88516, have characteristics which link them to the shergottite group of SNC meteorites. Essentially, ALH A77005 and LEW 88516 are feldspathic harzburgites, being comprised of roughly equal quantities of olivine and pyroxene, with an additional few percent of feldspar which has subsequently been converted to maskelynite by shock. The meteorites represent samples of a cumulate rock which is itself composed of two different lithologies: in one, large pyroxenes poikilitically enclose olivine crystals, while the other consists of interstitial areas made up of pyroxene, olivine, maskelynite, whitlockite, troilite, ilmenite and chlorapatite. It has been proposed that meteorites such as ALH A77005 (and LEW 88516) are relict samples of the source peridotite from which the other shergottites formed. As such it should be informative to study in detail the carbon components present within these samples, in order to make comparisons with data from other shergottites. Although not plutonic in origin, and therefore not sampling a truly deep source, analyses of ALH A77005 and LEW 88516 should assist with attempts to define the bulk carbon isotopic composition of Mars. This has been assessed previously through analyses of carbon of presumed magmatic origin in other SNC meteorites, but the carbon isotopic compositions obtained seem to be at variance with what might be expected. It is important to constrain the carbon isotopic composition of Mars as well as possible so that models of atmospheric evolution, based on carbon isotopic data, can yield the most reliable results.

Wright, I. P.↗

NASA NTRS1993

Further carbon isotope measurements of LEW 88516

Douglas et al. have previously analyzed the carbon content and isotopic composition of a crushed sample (sub-sample 13) of the shergottite, LEW 88516. The powder, which was from a relatively large portion of the meteorite in order to obtain a representative sample, was distributed amongst the scientific community. However, it is probable that the preparation procedure was not optimized for the purposes of carbon measurements. Indeed, it was found that LEW 88516,13 contained over 1200 ppm carbon, a concentration which is greater than that present in any other SNC meteorite. That a close relative, ALH A77005, contains only 141 ppm carbon seems to implicate the preparation procedure as being responsible for the apparently high carbon content of LEW 88516. However, it may also be the nature of the fine powder which has resulted in contamination. The observation of high carbon content in LEW 88516,13 highlights the extreme difficulty of trying to obtain representative samples of whole meteorites for this kind of investigation. Presented herein are some further measurements of LEW 88516 which should serve to clarify some of the issues raised by the previous investigation.

Wright, I. P.↗

NASA NTRS1993

An attempt to comprehend Martian weathering conditions through the analysis of terrestrial palagonite samples

Spectroscopic observations of the Martian surface in the invisible to near infrared (0.4-1.0 micron), coupled with measurements made by Viking, have shown that the surface is composed of a mixture of fine-grained weathered and nonweathered minerals. The majority of the weathered components are thought to be materials like smectite clays, scapolite, or palagonite. Until materials are returned for analysis there are two possible ways of proceeding with an investigation of Martian surface processes: (1) the study of weathering products in meteorites that have a Martian origin (SNC's), and (2) the analysis of certain terrestrial weathering products as analogs to the material found in SNC's, or predicted to be present on the Martian surface. We describe some preliminary measurements of the carbon chemistry of terrestrial palagonite samples that exhibit spectroscopic similarities with the Martian surface. The data should aid the understanding of weathering in SNC's and comparisons between terrestrial palagonites and the Martian surface.

Douglas, C.↗

NASA NTRS1990

Megawatt solar power systems for lunar surface operations

The work presented here shows that a solar power system can provide power on the order of one megawatt to a lunar base with a fairly high specific power. The main drawback to using solar power is still the high mass, and therefore, cost of supplying energy storage through the solar night. The use of cryogenic reactant storage in a fuel cell system, however, greatly reduces the total system mass over conventional energy storage schemes.

Adams, B.↗

NASA NTRS1984

Analysis of cure in composites processing

Finite element analysis is a general numerical tool for solving the field equations of engineering practice, and this paper demonstrates its use in modeling the nonisothermal cure of pultruded composite material. A very simple grid is used in this case to model a narrow strip of material, and this grid is then solved using a time-stepping transient algorithm to simulate the passage of the strip along the pultruder die. As time proceeds, heat is conducted into the strip from the heated boundaries at the die walls, and cure proceeds at a rate dependent on the local temperature. The computer model can be used to minimize the time needed for sufficient cure, and helps avoid such processing errors as undercure or thermal degradation.

Aylward, L.↗

NASA NTRS1982

Chemorheology of reactive systems: Finite element analysis

The equations which govern the nonisothermal flow of reactive fluids are outlined, and the means by which finite element analysis is used to solve these equations for the sort of arbitrary boundary conditions encountered in industrial practice are described. The performance of the computer code is illustrated by several trial problems, selected more for their value in providing insight to polymer processing flows than as practical production problems. Although a good deal remains to be learned as to the performance and proper use of this numerical technique, it is undeniably useful in providing better understanding of today's complicated polymer processing problems.

Douglas, C.↗

NASA NTRS1982

Finite element analysis of nonisothermal polymer processing operations

A finite element formulation for the analysis of polymer processing is presented and its use in some typical situation including entry flow, transient Couette flow, and the Graetz (forced convection) problem is illustrated. The element formulations are constructed on the premise that momentum convection can be neglected (polymer melt flows typically have very low Reynolds' numbers), but that convective heat transfer may be significant (high Peclet numbers). Nonisothermal effects are considered important in polymer processing, due in part to the significant heating which may occur due to viscous dissipation, and also to the very strong influence of temperature on fluid viscosity. The flow is treated as Newtonian with the flow field being coupled to the heat transfer equation only through the viscous heat generation.

Douglas, C.↗