Dogan, Omer | Engineering Papers

DOE OSTI2024

Creep Degradation of Austenitic Steels in CO2 Environments

Steels have a proven track record of safe operation in steam power plants for decades. Interest in developing supercritical CO2 power cycles as a more efficient and sustainable alternative to steam cycles has driven a need to understand steel performance in these new environments. In particular, the potential of the high temperature CO2 environment to influence the creep behavior of the steel must be determined. Prior research on this topic between the 1960s and 1980s found conflicting conclusions, but nevertheless raised the possibility that carburization during CO2 exposure may strongly affect the creep behavior. This raises concerns particularly for thin-sectioned components such as compact heat exchangers, where even small rates of carburization can become problematic over long operating lifetimes. To shed light on this issue, this research investigates the creep behavior of austenitic stainless steel 347H and 309H (a higher Cr alternative) at 650°C. Specimens of 0.5, 1.0, and 2.0 mm thickness were tested to further assess the effect of steel thickness. Both steels show a reduction in creep life in CO2 relative to air, with 309H showing slightly better performance than 374H. Analysis is ongoing to determine the reason for degraded creep properties.

Rozman, Kyle A.↗

DOE OSTI2024

Creep behavior of austenitic steels in CO2 and the effect of specimen thickness

Steels have a proven track record of safe operation in steam power plants for decades. Interest in developing supercritical CO2 power cycles as a more efficient and sustainable alternative to steam cycles has driven a need to understand steel performance in these new environments. In particular, the potential of the high temperature CO2 environment to influence the creep behavior of the steel must be determined. Prior research on this topic between the 1960s and 1980s found conflicting conclusions, but nevertheless raised the possibility that carburization during CO2 exposure may strongly affect the creep behavior. This raises concerns particularly for thin-sectioned components such as compact heat exchangers, where even small rates of carburization can become problematic over long operating lifetimes. To shed light on this issue, this research investigates the creep behavior of austenitic stainless steel 347H and 309H (a higher Cr alternative) at 650°C. Specimens of 0.5, 1.0, and 2.0 mm thickness were tested to further assess the effect of steel thickness. Both steels show a reduction in creep life in CO2 relative to air, with 309H showing slightly better performance than 374H. Analysis is ongoing to determine the reason for degraded creep properties.

Rozman, Kyle A.↗

DOE OSTI2024

Phase-Field Modeling of Thermally-Grown Oxide and the Induced Damage Evolution in Environmental Barrier Coatings

The advent of next-generation hydrogen-based engines necessitates materials capable of withstanding temperatures beyond the reach of current superalloys. SiC-based ceramic matrix composites, augmented with environmental barrier coatings (EBCs), present a promising materials solution. Given the active search for effective and durable EBCs, there is a pressing need for modeling tools to understand and predict damage evolution in these materials to help accelerate their development. This study introduces a phase-field model (PFM) designed to simulate the critical role of thermally grown oxides (TGO) in the degradation and failure of EBCs. The model accounts for the severe volume expansion due to oxidation, alongside phase transformations and microstructural evolution during thermal cycling, offering a comprehensive view of the damage processes. Simulation results are validated against experimental findings reported in the literature, establishing the model's potential as a significant tool for understanding and improving the resilience of EBCs in cyclic oxidative environments.

Cheng, Tianle↗

DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured H282 in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in high temperature and pressure direct-fired supercritical CO2 power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can result in additional corrosion behaviors. Utilizing additive manufacturing (AM) methods for construction of power cycle components requiring both compact and complex designs could be advantageous. AM H282 produced by laser powder bed fusion was exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure and supercritical conditions (20 MPa) for up to 4,000 hours. Oxidation behavior, sub-surface carbide formation, and chromia scale volatilization was dependent upon AM preparation techniques and surface modifications. These results are discussed in terms of the potential compatibility issues that may arise when using AM alloys in high temperature regions of direct-fired sCO2 power cycles, particularly for thin-walled components.

Carney, Casey↗

DOE OSTI2024

Phase-Field Modeling of Mechanical Damages in Ceramic Matrix Composites

Developed a phase-field model for mechanical damages in CMCs, which incorporates the CMC microstructures, matrix cracking, fiber breakage, and interfacial sliding. Two types of mechanisms, fiber bridging and fiber pull-out, are considered. The obtained simulation results agree with experimental observations and an analytical solution. Simulation results suggest that the performance of CMCs would be enhanced with thicker fibers, longer fibers, and higher fiber density. Opposite trends of interfacial sliding resistances are suggested for the two types of situations. In reality, a mixture of the two situations may exist, and then an intermediate interfacial sliding resistance may be optimal.

Xue, Fei↗

DOE OSTI2024

Environmental Compatibility Issues for Ni-Based Alloys in Direct-Fired Supercritical CO2 Power Cycles

Direct-fired supercritical CO2 (sCO2) power cycles offer potential for high-efficiency power generation from natural gas and other fossil fuels with built-in carbon capture. Ni-based superalloys are the leading candidates for the hottest portions of these systems, where they must endure long-term exposure to high-temperature, high-pressure, high-velocity, impure CO2-rich environments. Herein we describe results of various experimental testing campaigns conduced at NETL showing that under such conditions, several simultaneously occurring degradation modes may be active including surface oxidation, alloy carburization, and oxide volatilization. It will be shown that the rates of degradation can be strongly affected by the alloy composition, impurities in the CO2, manufacturing method (wrought vs additive), and other factors. The influence of these factors in controlling alloy degradation are discussed in the context of potential compatibility issues for components in real sCO2 systems, such as compact heat exchangers. Finally, as a potential remedial measure, ongoing work involving protective coatings suitable for complex geometries is presented.

alloy oxidation↗

DOE OSTI2024

Accelerated Design of Cost-Effective Thermal/Environmental Barrier Coatings based on High-Entropy Rare Earth Disilicates: A First-Principles Study

This project aims to design cost-effective thermal/environmental barrier coatings (TEBC) based on high entropy rare earth disilicates to protect SiC-based ceramic matrix composites from chemical and thermal attack for better performance of components in the hot section of gas turbine engines. To accelerate the alloy design, we utilize first-principles density functional theory (DFT) together with combinatorial chemistry methodology to predict key properties including phase stability, apparent bulk coefficient of thermal expansion (ABCTE), intrinsic lattice thermal conductivity, and temperature-dependent elastic constants. Specifically, this project focuses on β-RE2Si2O7 (RE=Yb, Y, Er, Lu, La, Ce,) with β-Yb2Si2O7 and β-Y2Si2O7 as the benchmark. Our DFT calculations predict that Er1/4Lu1/4Y3/4Yb3/4Si2O7 and Er1/2Lu1/2Y1/2Yb1/2Si2O7 have ultralow lattice thermal conductivity < 0.23 W/m/K at 1500 K and a good match of average ABCTE (5.1 - 5.2×10-6 K-1) with SiC. Owing to the low cost and abundant supply of Ce and La, the A- and G-La2Si2O7/Ce2Si2O7 disilicates are also studied. Our study shows that G-phase Ce2Si2O7 has an ultralow thermal conductivity (0.26 W/m/K at 1500 K) and the apparent bulk ABCTE (≈6.9×10-6 K-1) slightly higher than SiC, demonstrating great potential as low-cost high-performance T/EBC. However, La2Si2O7 and Ce2Si2O7 undergo an A-phase to G-phase polymorphic transition at around 1470 K.

environmental barrier coatings↗

DOE OSTI2024

Monitoring the corrosion resistance of cold-spray coatings with membrane-based sensors

In this presentation, the MBES shows the ability to detect the change in exposed environment even with cold-spray coatings. Corrosion rates from the cold-spray coating were comparable to a 316 stainless steel sample. Defects in the coating did not impact sensor performance in terms of corrosion rate or water content detection. Energy dispersive X-ray spectroscopy was used to document ion migration into the membrane.

Rendon, Arnaldo↗

DOE OSTI2024

Advanced Reaction Systems

An overview of NETL's Gasification Systems R&D was provided at DOE's Hydrogen and Fuel Cells Technology Office (HFTO) Annual Merit Review (AMR) on May 7, 2024, in Arlington, VA. The objective of the Advanced Reaction Systems Portfolio is to design, develop, and analyze technologies to support the mission of the Gasification Program to enable the use of diverse feedstocks to produce hydrogen and other value-added products with net-zero greenhouse gas emissions.

Lewis, Eric↗