Engineering Papers⌕ Search

Engineering topics

Dodbele, S. S.

Publications and source records attributed to Dodbele, S. S..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Effects of compressibility on design of subsonic fuselages for natural laminar flow

Compressible linear boundary-layer stability analyses of two representative axisymmetric fuselage geometries indicate that a favorable effect will be exerted on the characteristics of a fuselage's axisymmetric boundary layer by compressibility. A freestream Mach number increase from 0.6 to 0.8 significantly reduces TS wave growth rates in the laminar boundary layer of the fuselages analyzed. The generally destabilizing effect of increasing length Re number on boundary layer stability can be overpowered by the favorable effects of compressibility on the fluid.

Vijgen, P. M. H. W.↗
NASA NTRS1988

Analysis of wind-tunnel boundary-layer transition experiments on axisymmetric bodies at transonic speeds using compressible boundary-layer stability theory

The design of laminar flow fuselages and advanced swept wings at high-subsonic compressible speeds can benefit from a correlation of compressible transition experiments with the e exp n transition-prediction method. A computational analysis has been conducted to investigate the detailed transition measurements obtained by Boltz et al. (1956, 1960) for two bodies-of-revolution. Nonadiabatic wall conditions were included in the analysis when wall-temperature measurements were available.

Vijgen, P. M. H. W.↗
NASA NTRS1987

Status report on a natural laminar-flow nacelle flight experiment

The natural laminar flow (NLF) nacelle experiment is part of a drag reduction production program, and has the dual objectives of studying the extent of NLF on full scale nacelles in a flight environment and the effect of acoustic disturbance on the location of transition on the nacelle surface. The experiment is being conducted in two phases: (1) an NLF fairing was flown on a full scale Citation nacelle to develop the experiment technique and establish feasibility; (2) full scale, flow through, NLF nacelles located below the right wing of an experimental NASA OV-1 aircraft are evaluated. The measurements of most interest are the static pressure distribution and transition location on the nacelle surface, and the fluctuating pressure levels associated with the noise sources. Data are collected in combinations of acoustic frequencies and sound pressure levels. The results of phase 2 tests to date indicate that on shape GE2, natural laminar flow was maintained as far aft as the afterbody joint at 50 percent of the nacelle length. An aft facing step at this joint caused premature transition at this station. No change was observed in the transition pattern when the noise sources were operated.

Hastings, Earl C., Jr.↗
NASA NTRS1987

Nacelle aerodynamic performance

The boundary layer transition location was measured on a nacelle shape using the sublimating chemical flow visualization technique. This technique involves coating the surface with a thin film of volatile chemical solid, which, during exposure to a free stream airflow, rapidly sublimates in the turbulent boundary layer as a result of high shear stress and high mass transfer near the surface. Transition is indicated because the chemical coating remains relatively unaffected in the laminar region due to lower shear and low mass transfer. The slow response time of the chemical in a laminar boundary allowed for two test conditions during the same flight. The aircraft was first flown at the desired airspeed and altitude with the noise source off. Once a pattern had developed, the noise source was turned on to the desired setting and a new chemical pattern was sought. In this fashion a direct comparison of the effect of the noise could be determined.

Obara, Clifford J.↗
NASA NTRS1987

Loss of lift due to thickness for low-aspect-ratio wings in incompressible flow

The problem under consideration is a numerical study of the effects of thickness on lift for low-aspect-ratio wings in steady incompressible inviscid flow at moderate angles of attack. At these angles of attack the flow separates along the leading edge giving rise to a lift substantially higher than that computed by classical attached-flow potential theory. The problem is treated as a perturbation expansion in a small thickness parameter. The lifting elements of the flow are modeled using a nonlinear vortex-lattice method which replaces the leading and trailing-edge vortex sheets by segmented straight vortex filaments. The thickness elements of the flow are modeled with a mean-plane source distribution and a modification to the wing boundary conditions. Results are obtained for wings with biconvex and NACA 0012 sections which compare well with available experimental data. The important observation that the effect of thickness is to decrease the lift is made.

Dodbele, S. S.↗
NASA NTRS1987

Effects of forebody geometry on subsonic laminar boundary layer stability

The effect of forebody geometry on the stability of the laminar boundary layer on axisymmetric body shapes at Reynolds numbers typical of small and medium sized aircraft in low-subsonic cruise flight is investigated. It is found that small nose radii are important in obtaining n-factors of 9 on axisymmetric bodies of fineness ratio of about 6 at large nondimensional axial distances downstream. Results for the effect of the steepness of the pressure gradient and the value of the minimum pressure on the extent of laminar flows on an axisymmetric body at a given Reynolds number are also presented.

Dodbele, S. S.↗
NASA NTRS1986

Flight research on natural laminar flow nacelles - A progress report

This paper presents a progress report on an ongoing flight experiment for natural laminar flow nacelles. The results given herein were obtained during the first phase of the experiment, in which an instrumented natural laminar flow nacelle fairing was flight tested in the presence of turbofan engine noise and a controlled noise source. The results indicate that with the controlled noise source off, natural laminar flow was measured as far aft as 37 percent of the fairing length. The transition front was irregular in contour, and the extent of natural laminar flow was significantly affected by the relative flow angle for the fairing. In addition to these test results, the paper discusses the results of some recent computational analyses to predict pressure distributions and transition location, and to explain some of the data trends. Comparisons between measured and predicted data indicate that the analytical methods successfully predicted trends for the baseline (no controlled noise source) studies.

Hastings, E. C., Jr.↗
NASA NTRS1986

Design of fuselage shapes for natural laminar flow

Recent technological advances in airplane construction techniques and materials allow for the production of aerodynamic surfaces without significant waviness and roughness, permitting long runs of natural laminar flow (NLF). The present research effort seeks to refine and validate computational design tools for use in the design of axisymmetric and nonaxisymmetric natural-laminar-flow bodies. The principal task of the investigation involves fuselage body shaping using a computational design procedure. Analytical methods were refined and exploratory calculations conducted to predict laminar boundary-layer on selected body shapes. Using a low-order surface-singularity aerodynamic analysis program, pressure distribution, boundary-layer development, transition location and drag coefficient have been obtained for a number of body shapes including a representative business-aircraft fuselage. Extensive runs of laminar flow were predicted in regions of favorable pressure gradient on smooth body surfaces. A computational design procedure was developed to obtain a body shape with minimum drag having large extent of NLF.

Dodbele, S. S.↗
NASA NTRS1986

Shaping of airplane fuselages for minimum drag

The VSAERO surface panel method is employed to investigate fuselage shapes which can enhance the natural laminar flow (NLF) characteristics. The study is performed at cruise Re which are relevant to commuter, transport, and business aircraft. The technique is based on piecewise constant doublet and source singularities and takes into account the effects of compressibility. Inviscid pressure distributions were generated for five configurations to aid in the search for an optimized NLF body shape as a function of the transition locations and the drag coefficients. Granville's transition criteria are incorporated into the calculations to yield shapes with longer runs of laminar flow and reduced drag. In comparison with other transition prediction methods, the method described is shown to have significantly higher valicity for making three-dimensional transition predictions.

Dodbele, S. S.↗
NASA NTRS1985

Lift due to thickness for low aspect ratio wings in incompressible flow

The problem under consideration is a numerical study of the effects of thickness on lift for low aspect ratio wings in steady incompressible inviscid flow at moderate angles of attack. At these angles of attack the flow separates along the leading edge giving rise to a lift substantially higher than that computed by classical attached flow potential theory. The problem is treated as a perturbation expansion in a small thickness parameter. The lifting elements of the flow are modeled using a nonlinear vortex lattice method which replaces the leading and trailing edge vortex sheets by segmented straight vortex filaments. The thickness elements of the flow are modeled with a mean plane source distribution and a modification to the wing boundary conditions. Results are obtained for wings with biconvex and NACA 0012 sections which compare well with available experimental data. The important observation that the effect of thickness is to decrease the lift is made.

Dodbele, S. S.↗
NASA NTRS1984

Prediction of vortex lift on interacting delta wings in incompressible flow

Vortex flow modeling is used to calculate the steady inviscid incompressible flow past one, two and three delta wing configurations. The wings are modeled with vortex lattices and the leading and trailing-edge sheets are modeled by segmented straight vortex filaments. Aerodynamic characteristics are obtained for a range of geometry and angle of attack.

Dodbele, S. S.↗