Engineering topics
Dobrinskaya, Tatiana
Publications and source records attributed to Dobrinskaya, Tatiana.
An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles
This paper suggests a new method for optimizing yaw maneuvers on the International Space Station (ISS). Yaw rotations are the most common large maneuvers on the ISS often used for docking and undocking operations, as well as for other activities. When maneuver optimization is used, large maneuvers, which were performed on thrusters, could be performed either using control moment gyroscopes (CMG), or with significantly reduced thruster firings. Maneuver optimization helps to save expensive propellant and reduce structural loads ‐ an important factor for the ISS service life. In addition, optimized maneuvers reduce contamination of the critical elements of the vehicle structure, such as solar arrays. This paper presents an analytical solution for optimizing yaw attitude maneuvers. Equations describing pitch and roll motion needed to counteract the major torques during a yaw maneuver are obtained. A yaw rate profile is proposed. Also the paper describes the physical basis of the suggested optimization approach. In the obtained optimized case, the torques are significantly reduced. This torque reduction was compared to the existing optimization method which utilizes the computational solution. It was shown that the attitude profiles and the torque reduction have a good match for these two methods of optimization. The simulations using the ISS flight software showed similar propellant consumption for both methods. The analytical solution proposed in this paper has major benefits with respect to computational approach. In contrast to the current computational solution, which only can be calculated on the ground, the analytical solution does not require extensive computational resources, and can be implemented in the onboard software, thus, making the maneuver execution automatic. The automatic maneuver significantly simplifies the operations and, if necessary, allows to perform a maneuver without communication with the ground. It also reduces the probability of command errors. The suggested analytical solution provides a new method of maneuver optimization which is less complicated, automatic and more universal. A maneuver optimization approach, presented in this paper, can be used not only for the ISS, but for other orbiting space vehicles.
An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles
This paper presents a new method for optimizing yaw maneuvers, which are the most common large maneuvers on the International Space Station (ISS). The goal of the maneuver optimization is to find a maneuver trajectory with minimal torques acting on the vehicle during the maneuver. Therefore, the thruster firings necessary to perform the maneuver are minimized. Reduction of thruster firings saves propellant and decreases structural loads and contamination of the vehicle critical elements, thus saving the service life of the thrusters and the vehicle itself. Equations describing the pitch and roll motion needed to counteract the major torques during a yaw maneuver are obtained. Also, a yaw rate profile is suggested. In the obtained optimized case, the torques are significantly reduced. The proposed approximate analytical solution does not require extensive computer resources and, therefore, can be implemented using software onboard the ISS. As a result, the maneuver execution will be automatic. This is one of the major benefits of the simplified solution presented in this paper with respect to existing computational approaches. The suggested maneuver optimization method can be used not only for the ISS, but for other space vehicles as well.
An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles
No abstract available
Effect of Space Vehicle Structure Vibration on Control Moment Gyroscope Dynamics
Control Moment Gyroscopes (CMGs) are used for non-propulsive attitude control of satellites and space stations, including the International Space Station (ISS). CMGs could be essential for future long duration space missions due to the fact that they help to save propellant. CMGs were successfully tested on the ground for many years, and have been successfully used on satellites. However, operations have shown that the CMG service life on the ISS is significantly shorter than predicted. Since the dynamic environment of the ISS differs greatly from the nominal environment of satellites, it was important to analyze how operations specific to the station (dockings and undockings, huge solar array motion, crew exercising, robotic operations, etc) can affect the CMG performance. This task became even more important since the first CMG failure onboard the ISS. The CMG failure resulted in the limitation of the attitude control capabilities, more propellant consumption, and additional operational issues. Therefore, the goal of this work was to find out how the vibrations of a space vehicle structure, caused by a variety of onboard operations, can affect the CMG dynamics and performance. The equations of CMG motion were derived and analyzed for the case when the gyro foundation can vibrate in any direction. The analysis was performed for unbalanced CMG gimbals to match the CMG configuration on ISS. The analysis showed that vehicle structure vibrations can amplify and significantly change the CMG motion if the gyro gimbals are unbalanced in flight. The resonance frequencies were found. It was shown that the resonance effect depends on the magnitude of gimbal imbalance, on the direction of a structure vibration, and on gimbal bearing friction. Computer modeling results of CMG dynamics affected by the external vibration are presented. The results can explain some of the CMG vibration telemetry observed on ISS. This work shows that balancing the CMG gimbals decreases the effect of vehicle structure vibration on CMGs. Additionally, the effect of external vibrations may also be decreased by increasing the gimbal bearing friction. With the suggested modifications there may be no need to lower the gimbal rates below the nominal design requirements as it is currently done on ISS. The conclusions of this work