Engineering topics

Doane, George B., III

Publications and source records attributed to Doane, George B., III.

8 records

NASA NTRS1995

Special-Purpose High-Torque Permanent-Magnet Motors

Permanent-magnet brushless motors that must provide high commanded torques and satisfy unusual heat-removal requirement are developed. Intended for use as thrust-vector-control actuators in large rocket engines. Techniques and concepts used to design improved motors for special terrestrial applications. Conceptual motor design calls for use of rotor containing latest high-energy-product rare-earth permanent magnets so that motor produces required torque while drawing smallest possible currents from power supply. Torque generated by electromagnetic interaction between stator and permanent magnets in rotor when associated electronic circuits applied appropriately temporally and spatially phased currents to stator windings. Phase relationships needed to produce commanded torque computed in response to torque command and to electronically sensed angular position of rotor relative to stator.

Doane, George B., III↗

NASA NTRS1993

Advanced electric motor technology flux mapping

Design of electric motors which fulfill the needs of Thrust Vector Control (TVC) actuators used in large rocket propelled launch vehicles is covered. To accomplish this end the methodology of design is laid out in some detail. In addition a point design of a motor to fulfill the requirements of a certain actuator specified by MSFC is accomplished and reported upon. In the course of this design great stress has been placed on ridding the actuator of internally generated heat. To conduct the heat out of the motor use is made of the unique properties of the in house MSFC designed driving electronics. This property is that as along as they are operated in a quasi-linear mode the electronics nullify the effects of armature inductance as far as the phase of the armature current versus the rotor position is concerned. Actually the additional inductance due to the extended end turns in this design is of benefit because in the shorted armature failure mode the armature current in the fault (caused by the rotor flux sweeping past the armature) is diminished at a given rotor speed when compared to a more conventional motor with lower inductance. The magnetic circuit is analyzed using electromagnetic finite element methods.

Doane, George B., III↗

NASA NTRS1993

Research On Bi-Based High-Temperature Superconductors

Brief report describes effects of melt sintering on Bi-based high-temperature superconductor system, as well as use of vibrating-sample magnetometer to determine hysteresis curves at 77 K for partially melt-sintered samples. Also discussed is production of high-temperature superconducting thin films by laser ablation: such films potentially useful in detection of signals of very low power.

Banks, Curtis↗

NASA NTRS1992

Advanced electric motor technology: Flux mapping

This report contains the assumptions, mathematical models, design methodology, and design points involved with the design of an electromechanical actuator (EMA) suitable for directing the thrust vector of a large MSFC/NASA launch vehicle. Specifically the design of such an actuator for use on the upcoming liquid fueled National Launch System (NLS) is considered culminating in a point design of both the servo system and the electric motor needed. A major thrust of the work is in selecting spur gear and roller screw reduction ratios to achieve simultaneously wide bandwidth, maximum power transfer, and disturbance rejection while meeting specified horsepower requirements at a given stroking speed as well as a specified maximum stall force. An innovative feedback signal is utilized in meeting these diverse objectives.

Doane, George B., III↗

NASA NTRS1991

Propulsion stability codes for liquid propellant propulsion systems developed for use on a PC computer

Research into component modeling and system synthesis leading to the analysis of the major types of propulsion system instabilities and the characterization of various components characteristics are presented. Last year, several programs designed to run on a PC were developed for Marshall Space Flight Center. These codes covered the low, intermediate, and high frequency modes of oscillation of a liquid rocket propulsion system. No graphics were built into these programs and only simple piping layouts were supported. This year's effort was to add run time graphics to the low and intermediate frequency codes, allow new types of piping elements (accumulators, pumps, and split pipes) in the low frequency code, and develop a new code for the PC to generate Nyquist plots.

Doane, George B., III↗

NASA NTRS1991

Design controls for large order systems

The output of this task will be a program plan which will delineate how MSFC will support and implement its portion of the Inter-Center Computational Controls Program Plan. Another output will be the results of looking at various multibody/multidegree of freedom computer programs in various environments.

Doane, George B., III↗

NASA NTRS1990

PC programs for the prediction of the linear stability behavior of liquid propellant propulsion systems and application to current MSFC rocket engine test programs, volume 1

Research on propulsion stability (chugging and acoustic modes), and propellant valve control was investigated. As part of the activation of the new liquid propulsion test facilities, it is necessary to analyze total propulsion system stability. To accomplish this, several codes were built to run on desktop 386 machines. These codes enable one to analyze the stability question associated with the propellant feed systems. In addition, further work was adapted to this computing environment and furnished along with other codes. This latter inclusion furnishes those interested in high frequency oscillatory combustion behavior (that does not couple to the feed system) a set of codes for study of proposed liquid rocket engines.

Doane, George B., III↗

NASA NTRS1986

Development and use of a linear momentum exchange device

In 1981 the Marshall Space Flight Center (MSFC) began establishing an inhouse facility for testing control concepts to be applied to Large Space Structures (LSS). The original concept called for a long flexible beam suspended from the ceiling by a low friction support system. The lower end of the beam was to be mounted to the Advanced Gimbal System (AGS). Analysis and system engineering soon showed that a more tenable design would be where the whole system was inverted, i.e., the AGS hung from the ceiling with the beam hanging down from it. While this configuration, augmented by a base excitation table (RET) was being built, an ASTROMAST obtained from the Jet Propulsion Laboratory was extended, analyzed and tested. From that basic configuration was evolved the cruciform, VCOSS and ACES configurations as shown. The addition of the cruciform added low frequency nested modes and the additional instrument package at the tip contains gyros to monitor tip motion.

Doane, George B., III↗