Engineering Papers⌕ Search

Engineering topics

Divan, Ralu

Publications and source records attributed to Divan, Ralu.

83 records · Page 5

When are Surface Plasmon Polaritons Excited in the Kretschmann-Raether Configuration?

It is widely believed that the reflection minimum in a Kretschmann-Raether experiment results from direct coupling into surface plasmon polariton modes. Our experimental results provide a surprising discrepancy between the leakage radiation patterns of surface plasmon polaritons (SPPs) launched on a layered gold/germanium film compared to the K-R minimum, clearly challenging this belief. We provide definitive evidence that the reflectance dip in K-R experiments does not correlate with excitation of an SPP mode, but rather corresponds to a particular type of perfectly absorbing (PA) mode. Results from rigorous electrodynamics simulations show that the PA mode can only exist under external driving, whereas the SPP can exist in regions free from direct interaction with the driving field. These simulations show that it is possible to indirectly excite propagating SPPs guided by the reflectance minimum in a K-R experiment, but demonstrate the efficiency can be lower by more than a factor of 3. We find that optimal coupling into the SPP can be guided by the square magnitude of the Fresnel transmission amplitude.

Foley IV, Jonathan J.↗

A compact frequency tunable radio frequency phase shifter with patterned Py enabled transmission line

A well designed frequency tunable phase shifter using patterned Py with different thickness has been demonstrated. Phase shifter is implemented with a slow wave coplanar wave guide (CPW)transmission line, where the signal line has alternate short narrow and wide sections. Py is patterned on the top of narrow section for high inductance density, and inter-digital capacitor is implemented in wide section for high capacitance density. Compared with phase shifter using regular CPW, the dimension of the developed phase shifter has been reduced from 14.86 mm to4.70 mm at 2 GHz. Phase shifter based on 100 nm and 200 nm thick patterned Py with the same dimensions (14lm10lm) are implemented and investigated comprehensively. FMR frequency of 3.2 GHz and 3.6 GHz without any external magnetic field has been achieved for100 nm and 200 nm thick Py film, respectively. Thicker Py has increased inductance density from 1067.2 nH/m to 1193.2 nH/m while the center frequency of the phase shifter has been shifted to 1.80 GHz. Frequency tunability of the phase shifter has been also demonstrated withDC current. The phase shifter can provide 90phase shift continuously from 2 GHz to 1.80 GHz with DC current from 0 mA to 150 mA. As a result, the design concept has great potential in design arbitrary tunable RF components such as filters and couplers.

42 ENGINEERING↗

Application of sub-micrometer patterned permalloy thin film in tunable radio frequency inductors

Electrical tunable meander line inductor using coplanar waveguide structures with patterned permalloy (Py) thin film has been designed and implemented in this paper. High resistivity Si substrate is used to reduce the dielectric loss from the substrate. Inductor is implemented with a 60 nm thick Py deposited and patterned on top of the gold meander line, and Py film is patterned with dimension of 440 nm 10 lm to create the shape anisotropy field, which in turn increases the FMR frequency. Compared to a regular meanderline inductor without the application of sub-micrometer patterned Py thin film, the inductance density has been increased to 20% for the implemented inductor with patterned Py. Measured FMR frequency of the patterned Py is 4.51 GHz without the application of any external magnetic field. This has enabled the inductor application in the practical circuit boards, where the large external magnet is unavailable. Inductance tunability of the implemented inductor is demonstrated by applying a DC current. Applied DC current creates a magnetic field along the hard axis of the patterned Py thin film, which changes the magnetic moment of the thin film and thus, decreases the inductance of the line. Here, the measured results show that the inductance density of the inductor can be varied 5% by applying 300 mA DC current, larger inductance tunability is achievable by increasing the thickness of Py film.

36 MATERIALS SCIENCE↗

Tunable Transmission Line With Nanopatterned Thin Films for Smart RF Applications

A concept of tunable transmission line (TL) enabled with nanopatterned ferromagnetic permalloy (Py) and ferroelectric lead zirconium titanate (PZT) thin films is presented. The permittivity (εr) of PZT is electrical tunable with dc voltage, and the permeability (μr) of Py is electrical tunable with dc current, thus simultaneous electric tunable capacitance and inductance capability are provided for the proposed TL. The proposed TL has been fabricated and compared with a regular line without nanofilm patterns. Py is patterned with the dimensions of 10 μm × 150 nm and thickness of 100 nm for high built-in anisotropy field. The ferromagnetic resonant frequency is measured to be 6.3 GHz. Compared with the regular TL, the implemented TL has only generated 0.05 dB additional insertion loss at 4 GHz. The electrical tunability of both the capacitance and the inductance has been demonstrated for the first time. By applying the varied dc current (0–150 mA) and the dc voltage (0–20 V), measured results have shown that the proposed line can provide 90° phase shift from 3.75 to 4 GHz with the fixed characteristic impedance. The continuous tuning of the characteristics impedance from 59 to 61 under suitable bias conditions shows its promise as an impedance matching network. Tunable range of both the phase shifter and the impedance matching network can be further increased with thicker and multilayer films.

36 MATERIALS SCIENCE↗

Nitrogen incorporated ultrananocrystalline diamond based field emitter array for a flat-panel x-ray source

A field emission based flat-panel transmission x-ray source is being developed as an alternative for medical and industrial imaging. A field emitter array (FEA) prototype based on nitrogen incorporated ultrananocrystalline diamond film has been fabricated to be used as the electron source of this flat panel x-ray source. The FEA prototype was developed using conventional microfabrication techniques. The field emission characteristics of the FEA prototype were evaluated. Results indicated that emission current densities of the order of 6 mA/cm{sup 2} could be obtained at electric fields as low as 10 V/μm to 20 V/μm. During the prototype microfabrication process, issues such as delamination of the extraction gate and poor etching of the SiO{sub 2} insulating layer located between the emitters and the extraction layer were encountered. Consequently, alternative FEA designs were investigated. Experimental and simulation data from the first FEA prototype were compared and the results were used to evaluate the performance of alternative single and double gate designs that would yield better field emission characteristics compared to the first FEA prototype. The best simulation results are obtained for the double gate FEA design, when the diameter of the collimator gate is around 2.6 times the diameter of the extraction gate.

07 ISOTOPE AND RADIATION SOURCES↗

A Look Inside Argonne's Center for Nanoscale Materials

At a very small, or "nano" scale, materials behave differently. The study of nanomaterials is much more than miniaturization - scientists are discovering how changes in size change a material's properties. From sunscreen to computer memory, the applications of nanoscale materials research are all around us. Researchers at Argonne's Center for Nanoscale Materials are creating new materials, methods and technologies to address some of the world's greatest challenges in energy security, lightweight but durable materials, high-efficiency lighting, information storage, environmental stewardship and advanced medical devices.

36 MATERIALS SCIENCE↗

Determination of the Pt spin diffusion length by spin-pumping and spin Hall effect

The spin diffusion length of Pt at room temperature and at 8 K is experimentally determined via spin pumping and spin Hall effect in permalloy/Pt bilayers. Voltages generated during excitation of ferromagnetic resonance from the inverse spin Hall effect and anisotropic magnetoresistance effect were investigated with a broadband approach. Varying the Pt layer thickness gives rise to an evolution of the voltage line shape due to the superposition of the above two effects. By studying the ratio of the two voltage components with the Pt layer thickness, the spin diffusion length of Pt can be directly extracted. We obtain a spin diffusion length of ∼1.2 nm at room temperature and ∼1.6 nm at 8 K.

36 MATERIALS SCIENCE↗

Development of grating-based x-ray Talbot interferometry at the advanced photon source

We report on the ongoing effort to develop hard x-ray Talbot interferometry at the Advanced Photon Source (APS), Argonne National Laboratory, USA. We describe the design of the interferometer and preliminary results obtained at 25 keV using a feather and a phantom sample lithographically fabricated of gold. We mention the future developmental goals and applications of this technique as a metrology tool for x-ray optics and beam wavefront characterization.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Study of stress and adhesion strength in SU-8 resist layers on silicon substrate with different seed layers

We present the details of our study on the internal stresses and adhesion strengths of SU-8 structures to different substrate seed layers. The effect of adhesion promoter - methacryloxy [propl] trimethoxysilane (MPTS), and OmniCoat - and different seed layer combinations (Ti/Cu/Ti, Ti/Cu, Cr/Au, and Cr/Au/Cr) was examined for internal stress and adhesion strength in 650-{micro}m-thick SU-8 films. Increased stress and poor adhesion have led to the delamination of SU-8 in some cases. Adhesion and stress have proven to be the function of process parameters such as soft bake (time and temperature), exposure dose, post-exposure bake (time and temperature), and development time. We have found that a <100> silicon wafer containing a titanium-copper-titanium (Ti/Cu/Ti) seed layer with MPTS as the adhesion promoter yielded a thick SU-8 film with a lower value of stress and consequently better adhesion for processing in deep x-ray lithography (DXRL). A detailed correlation of the effects of adhesion and internal stress on the SU-8 film is discussed. An analysis of the possible chemical bonding interactions occurring between SU-8, and its adhesion promoter and/or substrate is also presented.

36 MATERIALS SCIENCE↗

Direct-current effects on magnetization reversal properties of submicron-size Permalloy patterns for radio-frequency devices

Ferromagnetic resonance (FMR) spectroscopy is used to measure direct-current (dc) effects on the magnetization reversal properties of submicron-sized lateral patterned magnetic material. The observed FMR frequency-field relationship shows that for both 240 and 550 nm wide Permalloy (Py) nanowires the coercivity is reduced by {approx}33% when a 50 mA dc passes through the transmission line where the nanowires are incorporated. The temperature dependence of the coercivity has a {radical}(T) relationship which suggests the coherent rotation mode tendency in such 100 nm thick Py nanowires.

77 NANOSCIENCE AND NANOTECHNOLOGY↗