Engineering topics

Dieudonne, J. E.

Publications and source records attributed to Dieudonne, J. E..

11 records

NASA NTRS1979

Verification and validation of the NASA Terminal Configured Vehicle's /TCV/ Wind Analysis program using real-time digital simulation

NASA's Terminal Configured Vehicle (TCV) program has been established to develop and evaluate aircraft and flight management technology that will benefit conventional takeoff and landing operations in the terminal area. To this end, a process whereby estimates of longitudinal, lateral, and vertical winds are obtained using the present complement of sensors onboard the TCV aircraft (B737-100) is developed. The results of the simulation experiment to verify and validate the TCV B737 Data Merging and Wind Analysis program have shown that the wind analysis algorithms are correct and that very satisfactory estimates of all three wind components are obtained even in the presence of adverse atmospheric conditions and realistic measurement noise. In realistic worst case conditions, wind component errors of the order of + or - 2.0 knots longitudinally, + or - 0.5 knot laterally, and + or - 1.0 knot vertically are to be expected.

Dieudonne, J. E.↗

NASA NTRS1979

Comments on a proposed standard wind hazard environment and its use in real-time aircraft simulations

A set of mean-wind profiles and associated turbulence models have been proposed by the FAA as a standard wind hazard environment to be used in piloted training and research simulators. The 'wind hazard package' is described along with a 'strawman' method of implementation into the real-time simulation of NASA's Terminal Configured Vehicle (TCV). Simulation results of both piloted and automatic landings have raised questions about the validity of the wind hazard environment, and the use of a lumped parameter quasi-steady flow aerodynamic model in this environment. Areas of discussion will include turbulence models, span and area averaging filters, gust penetration effects, and the need for the addition of terms in the moment equations to represent unsteady flow characteristics.

Dieudonne, J. E.↗

NASA NTRS1978

Description of a computer program and numerical techniques for developing linear perturbation models from nonlinear systems simulations

A numerical technique was developed which generates linear perturbation models from nonlinear aircraft vehicle simulations. The technique is very general and can be applied to simulations of any system that is described by nonlinear differential equations. The computer program used to generate these models is discussed, with emphasis placed on generation of the Jacobian matrices, calculation of the coefficients needed for solving the perturbation model, and generation of the solution of the linear differential equations. An example application of the technique to a nonlinear model of the NASA terminal configured vehicle is included.

Dieudonne, J. E.↗

NASA NTRS1978

Numerical derivation of linear perturbation model from nonlinear real-time vehicle simulations - A means of validation and increased credibility

A numerical technique has been developed which generates linear perturbation models from nonlinear real-time aircraft vehicle simulations at Langley Research Center. The technique is very general and can be applied to simulations of any system described by nonlinear differential equations. Linear models about various trim conditions have been obtained from simulations of the Boeing 737, Northrop F5-E, Cessna 180, Sikorsky CH-54, and NASA/Army Rotor Systems Research Aircraft (RSRA). One use of the derived linear models is as a validation and verification tool for the nonlinear simulation.

Dieudonne, J. E.↗

NASA NTRS1976

A simulation study of curved, descending, decelerating, landing approaches for transport aircraft

A system which is capable of controlling an aircraft automatically along a curved, descending, decelerating approach was described. A simulation study was conducted to determine the necessary modifications to the basic flight-proven control system. This basic system is presently being used to accomplish straight-in automatic landing approaches on a short-haul transport aircraft (B-737 terminal configured vehicle). This study shows that both 3 deg (normal) and 5 deg (steep) approaches could be accomplished with only minor modifications to the basic control system.

Dieudonne, J. E.↗

NASA NTRS1973

Motion software for a synergistic six-degree-of-freedom motion base

Computer software for the conversion of fixed-base simulations into moving-base simulations utilizing a synergistic six-degree-of-freedom motion simulator has been developed. This software includes an actuator extension transformation, inverse actuator extension transformation, a centroid transformation, and a washout circuit. Particular emphasis is placed upon the washout circuitry as adapted to fit the synergistic motion simulator. The description of the washout circuitry and illustration by means of a sample flight emphasize that translational cue representation may be of good fidelity, but care in the selection of parameters is very necessary, particularly in regard to anomalous rotational cues.

Parrish, R. V.↗

NASA NTRS1973

Compensation based on linearized analysis for a six degree of freedom motion simulator

The inertial response characteristics of a synergistic, six-degree-of-freedom motion base are presented in terms of amplitude ratio and phase lag as functions of frequency data for the frequency range of interest (0 to 2 Hz) in real time, digital, flight simulators. The notch filters which smooth the digital-drive signals to continuous drive signals are presented, and appropriate compensation, based on the inertial response data, is suggested. The existence of an inverse transformation that converts actuator extensions into inertial positions makes it possible to gather the response data in the inertial axis system.

Parrish, R. V.↗

NASA NTRS1973

Coordinated adaptive washout for motion simulators.

This paper introduces a new method of providing motion cues to a moving base six-degree-of-freedom flight simulator utilizing nonlinear filters. Coordinated adaptive filters, used to coordinate translational and rotational motion, are derived based on the method of continuous steepest descent, and the basic concept of the digital controllers used for the uncoordinated heave and yaw cues is also presented. The coordinated adaptive washout method is illustrated by an application in a six-degree-of-freedom fixed-base environment.

Parrish, R. V.↗

NASA NTRS1973

Coordinated adaptive filters for motion simulators.

A new approach to providing motion drive signals to a flight simulator utilizing coordinated adaptive filters is presented. Some motivation for the use of coordinated washout is discussed, along with conditions that determine the burden of coordination. The coordinated adaptive filters are derived, based on continuous steepest descent, and the application of the filters to simulated flight data is demonstrated.

Parrish, R. V.↗

NASA NTRS1972

An actuator extension transformation for a motion simulator and an inverse transformation applying Newton-Raphson's method

A set of equations which transform position and angular orientation of the centroid of the payload platform of a six-degree-of-freedom motion simulator into extensions of the simulator's actuators has been derived and is based on a geometrical representation of the system. An iterative scheme, Newton-Raphson's method, has been successfully used in a real time environment in the calculation of the position and angular orientation of the centroid of the payload platform when the magnitude of the actuator extensions is known. Sufficient accuracy is obtained by using only one Newton-Raphson iteration per integration step of the real time environment.

Dieudonne, J. E.↗

NASA NTRS1971

Application of Monte Carlo techniques to optimization of high-energy beam transport in a stochastic environment

An algorithm employing a modified sequential random perturbation, or creeping random search, was applied to the problem of optimizing the parameters of a high-energy beam transport system. The stochastic solution of the mathematical model for first-order magnetic-field expansion allows the inclusion of state-variable constraints, and the inclusion of parameter constraints allowed by the method of algorithm application eliminates the possibility of infeasible solutions. The mathematical model and the algorithm were programmed for a real-time simulation facility; thus, two important features are provided to the beam designer: (1) a strong degree of man-machine communication (even to the extent of bypassing the algorithm and applying analog-matching techniques), and (2) extensive graphics for displaying information concerning both algorithm operation and transport-system behavior. Chromatic aberration was also included in the mathematical model and in the optimization process. Results presented show this method as yielding better solutions (in terms of resolutions) to the particular problem than those of a standard analog program as well as demonstrating flexibility, in terms of elements, constraints, and chromatic aberration, allowed by user interaction with both the algorithm and the stochastic model. Example of slit usage and a limited comparison of predicted results and actual results obtained with a 600 MeV cyclotron are given.

Parrish, R. V.↗