Engineering Papers⌕ Search

Engineering topics

Diehl, W S

Publications and source records attributed to Diehl, W S.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1937

Considerations affecting the additional weight required in mass balance of ailerons

This paper is essentially a consideration of mass balance of ailerons from a preliminary design standpoint, in which the extra weight of the mass counterbalance is the most important phase of the problem. Equations are developed for the required balance weight for a simple aileron and this weight is correlated with the mass-balance coefficient. It is concluded the location of the c.g. of the basic aileron is of paramount importance and that complete mass balance imposes no great weight penalty if the aileron is designed to have its c.g. inherently near to the hinge axis.

Diehl, W S↗
NASA NTRS1928

Tests on Models of Three British Airplanes in the Variable Density Wind Tunnel

This report contains the results of tests made in the National Advisory Committee for Aeronautics variable density wind tunnel on three airplane models supplied by the British Aeronautical Research Committee. These models, the BE-2E with R.A.F. 19 wings, the British Fighter with R.A.F. 15 wings, and the Bristol Fighter with R.A.F. 30 wings, were tested over a wide range in Reynolds numbers in order to supply data desired by the Aeronautical Research Committee for scale effect studies. The maximum lifts obtained in these tests are in excellent agreement with the published results of British tests, both model and full scale. No attempt is made to compare drag data, owing to the emission of tail surfaces, radiator, etc., from the model, but is shown that the scale effect observed on the drag coefficients in these tests is due to a large extent to the parts of the models other than the wings. (author)

Higgins, George J↗
NASA NTRS1924

Static stability of seaplane floats and hulls

Values of lateral and longitudinal metacentric heights for various seaplanes were calculated by means of approximate formulae derived here. The data are given in tabular form. Upon plotting these metacentric heights against the corresponding gross weights, it appears that the metacentric height is approximately a straight line function of the gross weight. For the lateral metacentric height GM = 13 + .002 W and for longitudinal metacentric height GM = 15 + .002 W, GM is in feet and the gross weight (W) is in pounds. Although only approximate, it is thought that the values indicated here are a reliable guide to current practice. It is recommended that the longitudinal and lateral metacentric heights be made equal and of the value given by GM = 15 = .002 W. The proper length or spacing required to satisfy the indicated value may then be obtained from substitution in the approximate formulae for metacentric height.

Diehl, W S↗
NASA NTRS1923

Notes on the design of ailerons

Recent data have shown that certain forms or types of ailerons that are in extensive use are in reality quite inefficient and entirely unsuited for the high speeds now realized. The same data indicate that two forms (both shown here) are efficient and satisfactory in every way. The most important characteristics of ailerons are effectiveness under all flight conditions, small moments about the hinge, high efficiency (small yawing moment opposing turn), and simplicity in construction. Information required for the design of ailerons is given for chord, span, area, and plan form.

Diehl, W S↗
NASA NTRS1922

Comparative performance with direct and geared engines

Comprehensive tests were made to compare the performance of the F-5-L Boat Seaplane fitted with direct drive and Liberty engines. Details are given on the test conditions. The conclusions of the comparison tests follow. 1) An F-5-L with geared engines takes off in approximately 90 percent of the time required for the same airplane with standard direct drive engines. An F-5-L with geared engines climbs in 20 minutes to an altitude approximately 20 percent greater than that obtained with the standard direct drive on the same airplane. 3) There is a large difference between the climbs of the two airplanes of the same type. This difference will always be more pronounced when the climb is normally slow. In the case of the F-5-L airplanes under construction, it is of the order of a 10 percent difference in altitude on a 20 minute climb. 4) The maximum speed of an F-5-L with geared engines is about 3.5 percent greater than the maximum speed of the same airplane with standard direct drive engines (at the same engine r.p.m.). 5) The fuel consumption is probably less effected by the type of drive than by inherent differences in the performance of different airplanes.

Diehl, W S↗
NASA NTRS1922

F-5-L Boat Seaplane : performance characteristics

Performance characteristics for the F-5-L Boat Seaplane are given. Characteristic curves for the RAF-6 airfoil and the F-5-L wings, parasite resistance and velocity data, engine and propeller characteristics, effective and maximum horsepower, and cruising performance are discussed.

Diehl, W S↗
NASA NTRS1922

Skin frictional resistance of plane surfaces in air

Given here is the most recent research on skin frictional resistance of plane surfaces in air that was conducted by Dr. Wieselsberger under the direction of Dr. Prandtl of Gottingen University. In all, 16 models were tested. These were divided into four groups, as follows: 1) cloth, in the original condition; 2) cloth, with the nap singed off; 3) cloth, with three coats of dope; and 4) cloth, with six coats of dope. Each group consisted of four models of uniform width, 1 meter, and of lengths of 0.5, 1.0, 1.5, and 2.0 meters. Tests were made on each model at speeds varying from 7.0 to 50 meters per second. The observed total resistance was corrected for the form resistance which was obtained from the pressure distribution on the end of the model. Previous tests had shown that the form resistance due to the rounded front edge used on the models was negligible. The results are expressed in terms of the absolute coefficient of frictionless resistance, C(sub F).

Diehl, W S↗
NASA NTRS1922

Surface area coefficients for airship envelopes

In naval architecture, it is customary to determine the wetted surface of a ship by means of some formula which involves the principal dimensions of the design and suitable constants. These formulas of naval architecture may be extended and applied to the calculation of the surface area of airship envelopes by the use of new values of the constants determined for this purpose. Surface area coefficients were calculated from the actual dimensions, surfaces, and volumes of 52 streamline bodies, which form a series covering the entire range of shapes used in the present aeronautical practice.

Diehl, W S↗