Engineering topics
Publications and source records attributed to Dennison, E. W..
The Cassini spacecraft will perform a detailed examination of the Saturnian system, including the release of a probe to study Saturn's largest satellite, Titan. The star tracker for the Cassini mission must provide accurate data during the entire flight including four years of measurement in a harsh radiation environment.
The Cassini spacecraft will launch October 1997 and will perform a detailed examination of the Saturnian system, including the release of a probe to study Saturn's Largest satellite, Titan. The star tracker for the Cassini mission must provide accurate data during the 12 years of flight including four years of mesurement in a harsh radiation environment.
Charge-coupled device (CCD) optical sensors have made it possible to construct high performance star and target trackers for spacecraft. The Advanced Star and Target Reference Orbital Sensor (ASTROS) trackers have been developed by JPL for the Shuttle-based astronomical flight Astro-1 and the Mariner Mark II (MMII) spacecraft. For the Shuttle application the tracker will provide the data for high precision instrument pointing and for the MMII application the tracker will provide stellar and extended target tracking data for flyby and rendezvous navigation. The specifications, architecture, and testing program for these trackers will be described. Laboratory measurements have demonstrated that these trackers can be very effective. The versatility and flexibility of the ASTROS type trackers will permit adaptation to a variety of navigation and guidance applications. These trackers represent one of the technologically advanced components that will be used in the development of the next generation of spacecraft.
The architecture, capabilities, and testing of the Advanced Star and Target Reference Optical Sensor (ASTROS) I and II are described. The ASTROS I tracker is to be utilized for a UV telescope experiment on a Shuttle flight and is capable of measuring pointing errors of 1.5 microrad, and the ASTROS II tracker is being developed for the Mariner Mark II spacecraft to perform tracking, guiding, and optical navigation functions. The requirements for the two trackers are compared. Consideration is given to star and target tracking, optical navigation, and mass and power constraints. The compositions of the trackers, in particular the sensor, electrode drives, amplifiers and signal clamp, video signal processor, control and timing generator, memories, microprocessor, and interface, are examined.
In new alinement technique, no attempt made to simulate infinitely distant light source, and all mirrors left uncovered throughout procedure. Light source placed at distance of 1,650 feet (503 m); other distances used. Alinement of approximately 250 mirror facets of paraboloidal solar concentrator simplified by precalculated images reflected from all facets. Developed for large solar concentrators, technique used with other multiplemirror or multiple-light-source systems for producing specified illuminance patterns.
Insolation radiometers (normal incidence pyrheliometers) are used to measure the solar radiation incident on solar concentrators for calibrating thermal power generation measurements. The measured insolation value is dependent on the atmospheric transparency, solar elevation angle, circumsolar radiation, and radiometer field of view. The radiant energy entering the thermal receiver is dependent on the same factors. The insolation value and the receiver input will be proportional if the concentrator and the radiometer have similar fields of view. This report describes one practical method for matching the field of view of a radiometer to that of a solar concentrator. The concentrator field of view can be calculated by optical ray tracing methods and the field of view of a radiometer with a simple shroud can be calculated by using geometric equations. The parameters for the shroud can be adjusted to provide an acceptable match between the respective fields of view. Concentrator fields of view have been calculated for a family of paraboloidal concentrators and receiver apertures. The corresponding shroud parameters have also been determined.
Tracking accuracy and resolution of charge-coupled device (CCD) imaging arrays measured by instrument originally developed for measuring performance of star-tracking telescope. Operates by projecting one or more artifical star images on surface of CCD array, moving stars in controlled patterns, and comparing star locations computed from CCD outputs with those calculated from step coordinates of micropositioner.
Parabolic Dish Concentrator No. 1 (PDC-1) is a 12-m-diameter prototype concentrator with low life-cycle costs for use with thermal-to-electric energy conversion devices. The concentrator assembly features panels made of a resin transfer molded balsa core/fiberglass sandwich with plastic reflective film as the reflective surface and a ribbed framework to hold the panels in place. The concentrator assembly tracks in azimuth and elevation on a base frame riding on a circular track. It is shown that the panels do not exhibit the proper parabolic contour. However, thermal gradients were discovered in the panels with daily temperature changes. The PDC-1 has sufficient optical quality to operate satisfactorily in a dish-electric system. The PDC-1 development provides the impetus for creating innovative optical testing methods and valuable information for use in designing and fabricating concentrators of future dish-electric systems.
The optical characteristics of a paraboloidal solar concentrator are analyzed using the intercept factor curve (a format for image data) to describe the results of a mathematical model and to represent reduced data from experimental testing. This procedure makes it possible not only to test an assembled concentrator, but also to evaluate single optical panels or to conduct non-solar tests of an assembled concentrator. The use of three-dimensional ray tracing computer programs to calculate the mathematical model is described. These ray tracing programs can include any type of optical configuration from simple paraboloids to array of spherical facets and can be adapted to microcomputers or larger computers, which can graphically display real-time comparison of calculated and measured data.
Mirror figure evaluated in terms of imaging properties. Equipment includes scanner for measuring irradiance distribution in solar image produced by gore and camera equipped with special aperatures for determining magnitude and location of figure errors on gores.
The design, construction, and installation of the Parabolic Dish Concentrator, Type 1 (PDC-1) has been one of the most significant JPL concentrator projects because of the knowledge gained about this type of concentrator and the development of design, testing, and analysis procedures which are applicable to all solar concentrator projects. The need for these procedures was more clearly understood during the testing period which started with the prototype panel evaluation and ended with the performance characterization of the completed concentrator. For each phase of the test program, practical test procedures were required and these procedures defined the mathematical analysis which was essential for successful concentrator development. The concentrator performance appears to be limited only by the distortions resulting from thermal gradients through the reflecting panels. Simple optical testing can be extremely effective, but comprehensive mechanical and optical analysis is essential for cost effective solar concentrator development.
To insure that the insolation values accurately represent the input power to a power conversion unit the field of view (FOV) of the concentrator aperture and the insolation radiometer must be the same. The calculations, implementation, and results of this approach are covered. Three instruments were used to measure the insolation: an Eppley Normal Incidence Radiometer (NIP) and two versions of the kendall cavity radiometer. The shrouds used to limit the FOV of the radiometers were designed to simulate the FOV of the PDC-1 concentrater with the cold water cavity calorimeter. This technique of matching the FOV of an insolation radiometer to the FOV of a specific concentrater and receiver aperture appears to be both practical and effective. The efficiency of a power conversion unit will be too low if the insolation is measured with a radiometer which has a FOV which is larger than the FOV of the concentrator.
The design and application of ASTROS (Advanced Star and Target Reference Optical Sensor) are described, with emphasis on performance test results acquired with a prototype system. The ASTROS tracker provides extremely precise measurements of star image coordinates as inputs to the Image Motion Compensation (IMC) system used to stabilize the science instrument focal planes. Performance levels achieved are dramatic improvements over the levels achieved with image dissector designs with comparable fields of view.
A LaJet Energy Company (LEC) concentrator facet, 60 in. in diameter, was tested for imaging quality. The following two methods were used: (1) autofocus tests with a point source of light at the facet's radius of curvature; and (2) tests with the Sun close to the horizon as a distant source. The tests of the LaJet facet indicate that all of the solar image reflected by an LEC 460 solar concentrator made of like facets should fall within a 9-in. aperture if the outer facets are carefully adjusted. Such a concentrator would have acceptable performance, but complete evaluation must be made with an assembled concentrator.
The Jet Propulsion Laboratory 25-foot space simulator with its 5.8-m (19-ft) diameter simulated solar beam provides an excellent facility for measuring the optical characteristics of parabolic solar concentrator panels and gores. The virtual source position and size were determined by using a single lamp of the 37 xenon 30-kW source array with only the center lens in the 19-channel optical mixer. This data was used to define the optical test geometry, and it allowed accurate measurement of focal length and surface deviations of the mirror under test. A flux distribution of a typical solar concentrator placed directly on the solar beam gives measurements of performance at the focal point of the parabolic surface.
The optical imaging characteristics of parabolic solar concentrator panels (or gores) have been measured using the optical beam of the JPL 25-foot space simulator. The simulator optical beam has been characterized, and the virtual source position and size have been determined. These data were used to define the optical test geometry. The point source image size and focal length have been determined for several panels. A flux distribution of a typical solar concentrator has been estimated from these data. Aperture photographs of the panels were used to determine the magnitude and characteristics of the reflecting surface errors. This measurement technique has proven to be highly successful at determining the optical characteristics of solar concentrator panels.
Digital systems are discussed which have the capacity to handle the large amounts of information contained in a typical image. It was used with a high gain pulse counting television camera tube, with a silicon target image detector and an analog to digital converter between the detector and the memory.
Description of the digital memory and related computer system used at the Palomar Mountain Observatory. The memory was designed to have a large number of pixels, a high capacity for each pixel, and fast access for use with a variety of image sensors. As an image integration and storage device, this memory is shown to possess ideal properties, namely, it is strictly linear, has a wide dynamic range, and the image does not deteriorate with time. The observer has a visual display which enables him to monitor the image as it is being integrated.-