Engineering Papers⌕ Search

Engineering topics

Dengler, R. P.

Publications and source records attributed to Dengler, R. P..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Advanced secondary power system for transport aircraft

A concept for an advanced aircraft power system was identified that uses 20-kHz, 440-V, sin-wave power distribution. This system was integrated with an electrically powered flight control system and with other aircraft systems requiring secondary power. The resulting all-electric secondary power configuration reduced the empty weight of a modern 200-passenger, twin-engine transport by 10 percent and the mission fuel by 9 percent.

Hoffman, A. C.↗
NASA NTRS1984

The aerodynamic design and performance of the NASA/GE E3 low pressure turbine

The aerodynamic design and scaled rig test results of the low pressure turbine (LPT) component for the NASA/General Electric Energy Efficient Engine (E3) are presented. The low pressure turbine is a highly loaded five-stage design featuring high outer wall slope, controlled vortex aerodynamics, low stage flow coefficient, and reduced clearances. An assessment of its performance has been made based on a series of scaled air turbine tests which were divided into two phases: Block I (March through August, 1979) and Block II (June through September, 1981). Results from the Block II five-stage test, summarized in the paper, indicate that the E3 LPT will attain an efficiency level of 91.5 percent at the Mach 0.8/35,000 ft. max. climb altitude design point. This is relative to program goals of 91.1 percent for the E3 demonstrator engine and 91.7 percent for a fully developed flight propulsion system LPT.

Cherry, D. G.↗
NASA NTRS1976

Small, low cost, expendable turbojet engine. 2: Performance characteristics

A small experimental axial-flow turbojet engine was tested at sea level static conditions and over a range of simulated flight conditions to evaluate its performance as well as to demonstrate the feasibility of low-cost concepts utilized in its design. Testing was conducted at engine speeds as high as 37,000 rpm and at turbine inlet temperatures as high as 1,272 K. For maximum speed the engine produced a net thrust of 3,118 newtons at sea level static operation and 2,318 newtons at its cruise condition of M0 = 0.8 and 6,096 meters. Data obtained over a range of inlet Reynolds number indexes for nominal M0 of 0.38 revealed similar effects or trends on compressor characteristics of those previously established for much larger engines.

Dengler, R. P.↗
NASA NTRS1976

Small, low-cost, expendable turbojet engine. 1: Design, fabrication, and preliminary testing

A small experimental axial-flow turbojet engine in the 2,669-Newton (600-lbf) thrust class was designed, fabricated, and tested to demonstrate the feasibility of several low-cost concepts. Design simplicity was stressed in order to reduce the number of components and machining operations. Four engines were built and tested for a total of 157 hours. Engine testing was conducted at both sea-level static and simulated flight conditions for engine speeds as high as 38,000 rpm and turbine-inlet temperatures as high as 1,255 K (1,800 F).

Dengler, R. P.↗
NASA NTRS1975

Experience with integrally-cast compressor and turbine components for a small, low-cost, expendable-type turbojet engine

A discussion regarding experiences with integrally-cast compressor and turbine components during fabrication and testing of four engine assemblies of a small (29 cm (11-1/2 in.) maximum diameter) experimental turbojet engine design for an expendable application is presented. Various operations such as metal removal, welding, and re-shaping of these components are performed in preparation of full-scale engine tests. Engines with these components have been operated for a total of 157 hours at engine speeds as high as 38,000 rpm and at turbine inlet temperatures as high as 1256 K (1800 F).

Dengler, R. P.↗
NASA NTRS1975

Experience with integrally-cast compressor and turbine components for a small, low-cost, expendable-type turbojet engine

Experiences with integrally-cast compressor and turbine components during fabrication and testing of four engine assemblies of a small (29 cm (11 1/2 in.) maximum diameter) experimental turbojet engine design for an expendable application are discussed. Various operations such as metal removal, welding, and re-shaping of these components were performed in preparation of full-scale engine tests. Engines with these components were operated for a total of 157 hours at engine speeds as high as 38,000 rpm and at turbine inlet temperatures as high as 1256 K (1800 F).

Dengler, R. P.↗
NASA NTRS1973

Experimental investigation of aerodynamic performance of cooled turbine vanes at gas- to collant-temperature ratios up to 2.75

The results of an experimental investigation of the aerodynamic performance of two geometrically similar turbine vanes with different cooling designs are presented. The test vanes were a convection-film-cooled vanes and a transpiration-cooled vane. A solid uncooled vane with the same aerodynamic profile as the cooled vane was also tested. Four vanes of each type were tested in an annular sector cascade. The cooled vanes were tested at primary to coolant temperature ratios of 1.0, 1.75, and 2.75 and a coolant to primary pressure ratios of 1.0, 1.2, and 1.5. This resulted in coolant flows up to about 10 percent of the primary flow. The principal measurements were surveys of vane exit total pressure, total temperature, and static pressure. The report includes a brief description of the test facility and the design of the test vanes. The test results presented include weight flow and efficiency data for the uncooled vanes and coolant flow, primary flow, and efficiency data as functions of the cooling variables for the cooled vanes.

Stabe, R. G.↗
NASA NTRS1972

Engine investigation of an air-cooled turbine rotor blade incorporating impingement-cooled leading edge, chordwise passages, and a slotted trailing edge

Experimental temperatures are presented for an air-cooled turbine rotor blade tested in an engine. The data were obtained for turbine stator inlet temperatures from 2000 to 2500 F and for turbine-inlet gas pressures from 32 to 46 psia. Average and local blade heat-transfer data are correlated. Potential allowable increases in gas temperature are also discussed.

Dengler, R. P.↗
NASA NTRS1972

Experimental heat transfer and flow results of a chordwise-finned turbine vane with impingement, film, and convection cooling

Experimental heat transfer data are presented for a vane tested in a turbojet engine at turbine inlet gas temperatures to 1644 K (2500 F), coolant temperatures to 700 K (800 F), and coolant-to-gas flow ratios to 0.187. Methods are presented for correlating heat transfer data and obtaining coolant flow distribution through the vane. Calculated and measured coolant flow distributions and vane metal temperatures are compared.

Gauntner, J. W.↗
NASA NTRS1970

Lightweight, self-evacuated insulation panels

Multilayer insulation of prefabricated panels is developed for cryogenic storage tanks. System utilizes panels of aluminized Mylar separated by sheets of low conductivity polyurethane foam. Panels are self-evacuated by cryopumping of gaseous carbon dioxide at time of use.

Dengler, R. P.↗