Engineering Papers⌕ Search

Engineering topics

Dejarnette, F. R.

Publications and source records attributed to Dejarnette, F. R..

32 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Effects of aircraft and flight parameters on energy-efficient profile descents in time-based metered traffic

Attention is given to a computer algorithm yielding the data required for a flight crew to navigate from an entry fix, about 100 nm from an airport, to a metering fix, and arrive there at a predetermined time, altitude, and airspeed. The flight path is divided into several descent and deceleration segments. Results for the case of a B-737 airliner indicate that wind and nonstandard atmospheric properties have a significant effect on the flight path and must be taken into account. While a range of combinations of Mach number and calibrated airspeed is possible for the descent segments leading to the metering fix, only small changes in the fuel consumed were observed for this range of combinations. A combination that is based on scheduling flexibility therefore seems preferable.

Dejarnette, F. R.↗
NASA NTRS1983

Aerodynamic heating and surface temperatures on vehicles for computer-aided design studies

A computer subprogram has been developed to calculate aerodynamic and radiative heating rates and to determine surface temperatures by integrating the heating rates along the trajectory of a vehicle. Convective heating rates are calculated by applying the axisymmetric analogue to inviscid surface streamlines and using relatively simple techniques to calculate laminar, transitional, or turbulent heating rates. Options are provided for the selection of gas model, transition criterion, turbulent heating method, Reynolds Analogy factor, and entropy-layer swallowing effects. Heating rates are compared to experimental data, and the time history of surface temperatures are given for a high-speed trajectory. The computer subprogram is developed for preliminary design and mission analysis where parametric studies are needed at all speeds.

Dejarnette, F. R.↗
NASA NTRS1979

Investigation of aerodynamic characteristics of subsonic wings

An analytical strake design procedure is investigated. A numerical solution to the governing strake design equation is used to generate a series of strakes which are tested in a water tunnel to study their vortex breakdown characteristics. The strakes are scaled for use on a half-scale model of the NASA-LaRC general research fuselage with a 44 degrees trapezoidal wing. An analytical solution to the governing design equation is obtained. The strake design procedure relates the potential-flow leading-edge suction and pressure distributions to vortex stability. Several suction distributions are studied and those which are more triangular and peak near the tip generate strakes that reach higher angles of attack before vortex breakdown occurs at the wing trailing edge. For the same suction distribution, a conical rather than three dimensional pressure specification results in a better strake shape as judged from its vortex breakdown characteristics.

Dejarnette, F. R.↗
NASA NTRS1979

Aerodynamic heating on complex configurations

A relatively simple method was developed previously (DeJarnette and Hamilton, 1973; 1975) to calculate laminar transitional and turbulent heating rates on blunt bodies at angles of attack, taking into account entropy-swelling effects. The method has now been extended to include complex configurations and the use of input surface pressure data when available. Applications of the extended method to the HL-10 Lifting Body, a blunted tangent ogive, a blunted tangent-ogive cylinder, and the Viking Aeroshell are discussed.

Dejarnette, F. R.↗
NASA NTRS1976

Arrangement of vortex lattices

A new method is developed for solving the lifting-surface equation for thin wings. The solution requires the downwash equation to be in the form of Cauchy integrals which can be interpreted as a vortex lattice with the positions of the vortices and control points dictated by the finite sum used to approximate the integrals involved. Lan's continuous loading method is employed for the chordwise integral since it properly accounts for the leading-edge singularity, Cauchy singularity, and Kutta condition. Unlike Lan, the spanwise loading is also continuous and the Cauchy singularity in the spanwise integral is also properly accounted for by using the midpoint trapezoidal rule and the theory of Chebyshev polynomials. This technique yields the exact classical solution to Prandtl's lifting-line equation.The solution to the lifting-surface equation for rectangular wings was found to compare well with other continuous loading methods, but with much smaller computational times, and to converge faster than other vortex lattice methods.

Dejarnette, F. R.↗
NASA NTRS1976

Lifting surface theory for rectangular wings

A new incompressible lifting-surface theory is developed for thin rectangular wings. The solution requires the downwash equation to be in the form of Cauchy-type integrals. Lan's method is employed for the chordwise integrals since it properly accounts for the leading-edge singularity, Cauchy singularity and Kutta condition. The Cauchy singularity in the spanwise integral is also accounted for by using the midpoint trapezoidal rule and theory of Chebychev polynomials. The resulting matrix equation, formed by satisfying the boundary condition at control points, is simpler and quicker to compute than other lifting surface theories. Solutions were found to converge with only a small number of control points and to compare favorably with results from other methods.

Dejarnette, F. R.↗
NASA NTRS1975

Surface fitting three-dimensional bodies

The geometry of general three-dimensional bodies was generated from coordinates of points in several cross sections. Since these points may not be on smooth curves, they are divided into groups forming segments and general conic sections are curve fit in a least-squares sense to each segment of a cross section. The conic sections are then blended in the longitudinal direction through longitudinal curves. Both the cross-sectional and longitudinal curves may be modified by specifying particular segments as straight lines or specifying slopes at selected points. This method was used to surface fit a 70 deg slab delta wing and the HL-10 Lifting Body. The results for the delta wing were very close to the exact geometry. Although there is no exact solution for the lifting body, the surface fit generated a smooth surface with cross-sectional planes very close to prescribed coordinate points.

Dejarnette, F. R.↗
NASA NTRS1974

Surface fitting three-dimensional bodies

The geometry of general three-dimensional bodies is generated from coordinates of points in several cross sections. Since these points may not be smooth, they are divided into segments and general conic sections are curve fit in a least-squares sense to each segment of a cross section. The conic sections are then blended in the longitudinal direction by fitting parametric cubic-spline curves through coordinate points which define the conic sections in the cross-sectional planes. Both the cross-sectional and longitudinal curves may be modified by specifying particular segments as straight lines and slopes at selected points. Slopes may be continuous or discontinuous and finite or infinite. After a satisfactory surface fit has been obtained, cards may be punched with the data necessary to form a geometry subroutine package for use in other computer programs. At any position on the body, coordinates, slopes and second partial derivatives are calculated. The method is applied to a blunted 70 deg delta wing, and it was found to generate the geometry very well.

Dejarnette, F. R.↗
NASA NTRS1974

Aerodynamic heating on 3-D bodies including the effects of entropy-layer swallowing

A relatively simple method was developed previously (authors, 1973) for calculating laminar, transitional, and turbulent heating rates on three-dimensional bodies in hypersonic flows. This method was shown to yield reasonably accurate results for laminar heating on blunted circular and elliptical cones and an earlier version of the space shuttle vehicle. As the boundary layer along the surface grows, more and more of the inviscid-flow mass is entrained into the boundary layer, and the streamlines which passed through the nearly normal portion of the bow shock wave are 'swallowed' by the boundary layer. This phenomenon is often referred to as entropy-layer or streamline swallowing, and it can have a significant effect on the calculated heating rates. An approximate, yet simple, method for including the effects of entropy-layer swallowing in the heating-rate calculations is given.

Dejarnette, F. R.↗
NASA NTRS1972

Calculation of heat transfer on shuttle type configurations including the effects of variable entropy at boundary layer edge

A relatively simple method is presented for including the effect of variable entropy at the boundary-layer edge in a heat transfer method developed previously. For each inviscid surface streamline an approximate shockwave shape is calculated using a modified form of Maslen's method for inviscid axisymmetric flows. The entropy for the streamline at the edge of the boundary layer is determined by equating the mass flux through the shock wave to that inside the boundary layer. Approximations used in this technique allow the heating rates along each inviscid surface streamline to be calculated independent of the other streamlines. The shock standoff distances computed by the present method are found to compare well with those computed by Maslen's asymmetric method. Heating rates are presented for blunted circular and elliptical cones and a typical space shuttle orbiter at angles of attack. Variable entropy effects are found to increase heating rates downstream of the nose significantly higher than those computed using normal-shock entropy, and turbulent heating rates increased more than laminar rates. Effects of Reynolds number and angles of attack are also shown.

Dejarnette, F. R.↗
NASA NTRS1972

Inviscid surface streamlines and heat transfer on shuttle-type configurations.

A method is developed which calculates laminar, transitional, and turbulent heating rates on arbitrary blunt-nosed three-dimensional bodies at angle of attack in hypersonic flow. The geometry of the body may be specified analytically, or generated from a doubly cubic spline fit to coordinate points. Inviscid surface streamlines are calculated from Euler's equation using a prescribed pressure distribution. Laminar and turbulent heating rates are determined along a streamline by applying the axisymmetric analog to solutions of the axisymmetric boundary-layer equations. The location of the transition region may be specified optionally by geometric location, momentum thickness Reynolds number, or integrated unit Reynolds number along a streamline. Transitional heating rates are then calculated as a weighted average of the local laminar and turbulent values. Either ideal gas or equilibrium air properties may be used.

Dejarnette, F. R.↗
NASA NTRS1971

Calculation of inviscid surface streamlines and heat transfer on shuttle type configurations. Part 2: Description of computer program

A description of the computer program used for heating rate calculation for blunt bodies in hypersonic flow is given. The main program and each subprogram are described by defining the pertinent symbols involved and presenting a detailed flow diagram and complete computer program listing. Input and output parameters are discussed in detail. Listings are given for the computation of heating rates on (1) a blunted 15 deg half-angle cone at 20 deg incidence and Mach 10.6, (2) a blunted 70 deg slab delta wing at 10 deg incidence and Mach 8, and (3) the HL-10 lifting body at 20 deg incidence and Mach 10. In addition, the computer program output for two streamlines on the blunted 15 deg half-angle cone is listed. For Part 1, see N71-36186.

Dejarnette, F. R.↗