Engineering topics

Deffenbaugh, D. M.

Publications and source records attributed to Deffenbaugh, D. M..

4 records

NASA NTRS1999

Trade Study of Five In-Situ Propellant Production Systems for a Mars Sample Return Mission

One of the goals of NASA's HEDS enterprise is to establish a long-term human presence on Mars at a fraction of the cost of employing today's technology. The most direct method of reducing mission cost is to reduce the launch mass of the spacecraft. If the propellants for the return phase of the mission are produced on Mars, the total spacecraft mass could be reduced significantly. An interim goal is a Mars Sample Return (MSR) mission, which is proposed to demonstrate the feasibility of in-situ propellant production (ISPP). Five candidate ISPP systems for producing two fuels and oxygen from the Martian atmosphere are considered in this design trade-off study: 1) Zirconia cell with methanol synthesis, 2) Reverse water gas shift with water electrolysis and methanol synthesis, 3) Sabatier process for methane product ion with water electrolysis, 4) Sabatier process with water electrolysis and partial methane pyrolysis, and 5) Sabatier/RWGS combination with water electrolysis.

Green, S. T.↗

NASA NTRS1999

Trade Study of Five In-Situ Propellant Production System for a Mars Sample Return Mission

One of the goals of NASA''s HEDS enterprise is to establish a long-term human presence on Mars at a fraction of the cost of employing today''s technology. The most direct method of reducing mission cost is to reduce the launch mass of the spacecraft. If the propellants for the return phase of the mission are produced on Mars, the total spacecraft mass could be reduced significantly. An interim goal is a Mars Sample Return (MSR) mission, which is proposed to demonstrate the feasibility of in-situ propellant production (ISPP). Five candidate ISPP systems for producing two fuels and oxygen from the Martian atmosphere are considered in this design trade-off study:(1) Zirconia cell with methanol synthesis, (2) Reverse water gas shift (RWGS) with water electrolysis and methanol synthesis, (3) Sabatier process for methane production with water electrolysis, (4) Sabatier process with water electrolysis and partial methane pyrolysis, and (5) Sabatier/RWGS combination with water electrolysis. These systems have been the subject of numerous previous analytical studies and laboratory demonstrations. In this investigation, the systems are objectively compared on the basis of thermochemical performance models using a commonly used chemical plant analysis software package. The realistic effects of incomplete chemical conversion and gas phase separator performance are included in these models. This study focuses on the chemical processing and product separation subsystems. The CO2 compression upstream of the chemical plane and the liquefaction/storage components are not included here.

Green, S. T.↗

NASA NTRS1998

Liquid Motion in a Rotating Tank Experiment (LME)

The Liquid Motion Experiment (LME), which flew on STS 84 in May 1997, was an investigation of liquid motions in spinning, nutating tanks. LME was designed to quantify the effects of such liquid motions on the stability of spinning spacecraft, which are known to be adversely affected by the energy dissipated by the liquid motions. The LME hardware was essentially a spin table which could be forced to nutate at specified frequencies at a constant cone angle, independently of the spin rate. Cylindrical and spherical test tanks, partially filled with liquids of different viscosities, were located at the periphery of the spin table to simulate a spacecraft with off-axis propellant tanks; one set of tanks contained generic propellant management devices (PMDs). The primary quantitative data from the flight tests were the liquid-induced torques exerted on the tanks about radial and tangential axes through the center of the tank. Visual recordings of the liquid oscillations also provided qualitative information. The flight program incorporated two types of tests: sine sweep tests, in which the spin rate was held constant and the nutation frequency varied over a wide range; and sine dwell test, in which both the spin rate and the nutation frequency were held constant. The sine sweep tests were meant to investigate all the prominent liquid resonant oscillations and the damping of the resonances, and the sine dwell tests were meant to quantify the viscous energy dissipation rate of the liquid oscillations for steady state conditions. The LME flight data were compared to analytical results obtained from two companion IR&D programs at Southwest Research Institute. The comparisons indicated that the models predicted the observed liquid resonances, damping, and energy dissipation rates for many test conditions but not for all. It was concluded that improved models and CFD simulations are needed to resolve the differences. This work is ongoing under a current IR&D program.

Deffenbaugh, D. M.↗

NASA NTRS1979

Bellows flow-induced vibrations

Results of theoretical and experimental investigations of bellows typical of those found in space shuttle external tanks are presented. Correlation parameters are identified which generalize the alternating stress calculations cited in an earlier study. Alternating stress amplitudes and mean stress levels form the basis of a fatigue analysis incorporating seven ordinate charts for 347 stainless steel, alloy 21 6-9, and Inco 718. A crack propagation model is included with a program for computing bellows fatigue life. Two phase flow and material hardness properties are discussed.

Johnson, J. E.↗