Engineering Papers⌕ Search

Engineering topics

Dec, John E.

Publications and source records attributed to Dec, John E..

At least 19 records

Practical low-temperature gasoline combustion for very high efficiency off-road, medium- and heavy-duty engines

Low-temperature gasoline combustion (LTGC) with additive-mixing fuel injection (AMFI) is a new combustion strategy that has been demonstrated to deliver 9%–25% better brake thermal efficiency than similar-sized market-leading diesel engines over the operating map. Moreover, the LTGC-AMFI engine shows near-zero smoke, and NOx emissions are 4–100 times lower than those of a diesel, sufficiently low that no aftertreatment, or only passive NOx aftertreatment, would be sufficient (diesel exhaust fluid is not required). LTGC-AMFI combustion is based on kinetically controlled compression ignition of a dilute charge with a variable amount of low-to-moderate fuel stratification. Fast combustion control is provided by adding minute amounts of an ignition-enhancing additive into the fuel each engine cycle to control its reactivity. This strategy was used to operate a medium-duty (MD) LTGC-AMFI engine at loads from idle to 16.3 bar BMEP and speeds from 600 to 2400 rpm with regular E10 gasoline, which covers nearly the entire operating map of a typical MD engine. Turbine-out temperatures were sufficient for an oxidation catalyst to control hydrocarbon and CO emissions. Autonomie simulations over the GEM ARB Transient and the GEM 55 mph Cruise driving cycles for class-6 trucks using this technology showed fuel economies of 8.1 and 11.4 mpg-gasoline-equivalent, respectively, corresponding to 18.6% and 13.4% improvements over a similar-size diesel engine. Engine-out NOx emissions were 0.024 and 0.01 g/bhp-h, respectively, well below current U.S. emission standards. These results show that switching from diesel to LTGC-AMFI engines would greatly reduce greenhouse gas (GHG) emissions for off-road, MD and HD applications, which will continue to rely on combustion engines because electrification is not practical in the foreseeable future. Finally, with their reduced fuel consumption, the lower cost of gasoline compared to diesel fuel, and much lower aftertreatment costs, LTGC-AMFI engines also offer a significantly lower total cost of ownership.

33 ADVANCED PROPULSION SYSTEMS↗

Additives for improving autoignition reactivity of hydrocarbon-based fuels

According to various aspects, an additive for a hydrocarbon-based fuel has a formula (I), in which R 1 , R 2 , and R 3 are each independently selected from —H, —CH 3 , or —CH 2 CH 3 , and at least one of R 1 , R 2 , and R 3 is not —H. The additive improves an autoignition reactivity of the hydrocarbon-based fuel. The additive can be present in the fuel composition including the additive and the hydrocarbon-based fuel in an amount of 0.1% by volume to 5% by volume. The hydrocarbon-based fuel can comprise gasoline or diesel.

Lopez Pintor, Dario↗

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗

Fuel and fuel blend for internal combustion engine

A fuel or fuel blending agent for an internal combustion engine includes a ketone compound that is a C 4 to C 10 branched acyclic ketone, cyclopentanone, or a derivative of cyclopentanone. The ketone compound may be blended with a majority portion of a fuel selected from the group consisting of: gasoline, diesel, alcohol fuel, biofuel, renewable fuel, Fischer-Tropsch fuel, or combinations thereof. The ketone compound may be derived from biological sources. A method for powering an internal combustion engine with a fuel comprising the ketone compound is also provided.

Dec, John E.↗

Additive-Mixing Fuel Injection (AMFI): A device for robust control and improved performance of high-efficiency LTGC engines

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and particulate emissions. Despite these major advantages, methods for controlling LTGC combustion timing, achieving robust autoignition, and good low-load performance have challenged the development of practical LTGC engines. A key reason is that the ideal reactivity of the fuel varies with operating conditions, with low-reactivity fuels working well at high loads and higher-reactivity fuels working better at low loads. This article introduces a new technique called Additive Mixing Fuel Injection (AMFI) that adjusts the reactivity of the gasoline to obtain good performance over the operating map. Moreover, AMFI can provide robust combustion-timing control because it precisely meters very small amounts (0.01–0.6 mm 3 ) of an ignition-enhancing additive into the fuel each engine cycle. The additive used was 2-ethylhexyl nitrate (EHN), a common, inexpensive diesel-fuel ignition improver, but other additives could be used. Because additive amounts are so small, a 2-gal reservoir would be sufficient for medium-duty applications with refilling only at service intervals of about 8000 mi. The AMFI system has been installed on a single-cylinder LTGC research engine and demonstrated to provide robust combustion-timing control over wide ranges of combustion phasing, fueling rate, intake boost, engine speed, and intake temperature. AMFI also increases the fuel’s reactivity sufficiently to greatly reduce or eliminate the need for charge heating, simplifying engine design and significantly increasing thermal efficiency and the maximum load at low-boost conditions. The nitrogen in the EHN produced a modest increase in NOx, but it was mitigated by lower intake temperatures, and NOx emissions remained very low. Finally, the additive increases the sensitivity of autoignition reactions to variations in the local fuel/air mixture within the charge. This allows the use of controlled fuel stratification for improved LTGC-engine performance, and its potential to improve low-load operation was demonstrated.

Dec, John E.↗

Replicating HCCI-like autoignition behavior: What gasoline surrogate fidelity is needed?

This work seeks to characterize the fidelity needed in a gasoline surrogate with the intent to replicate the complex autoignition behavior exhibited within advanced combustion engines, and specifically Homogeneous Charge Compression Ignition (HCCI). A low-temperature gasoline combustion (LGTC) engine operating in HCCI mode and a rapid compression machine (RCM) are utilized to experimentally quantify fuel reactivity, through autoignition and preliminary heat release characteristics. Fuels considered include a research grade E10 U.S. gasoline (RD5-87), three multi-component surrogates (PACE-1, PACE-8, PACE-20), and a binary surrogate (PRF88.4). Each fuel was studied at lean/HCCI-like conditions covering a wide range of temperatures and pressures that are representative of naturally aspirated to high boost engine operation. Detailed chemical kinetic modeling is also undertaken using a recently updated gasoline surrogate kinetic model to simulate the RCM experiments and to provide chemical insight into surrogate-to-surrogate differences. The LGTC engine experiments demonstrate nearly identical reactivity between PACE-20 and RD5-87 across studied conditions, while faster phasing is seen for both PACE-1 and PACE-8 due to their stronger intermediate- and low-temperature heat release (ITHR/LTHR) at naturally aspirated and boosted conditions, respectively. The RCM experiments reveal typical low-temperature, negative temperature coefficient (NTC) and intermediate-temperature autoignition behaviors at all pressure conditions for RD5-87, which are qualitatively reproduced by all surrogates. Quantitative discrepancies in both autoignition and preliminary heat release are observed for all surrogates, while their ability to replicate RD5-87 autoignition behavior follows the order of PACE-20 > PACE-1 > PACE-8 > PRF88.4. Excellent mapping is obtained between the LGTC engine and the RCM, where the engine pressure-time trajectories can be characterized by the regimes represented by the RCM autoignition isopleths. The kinetic model performs commendably when simulating both autoignition and preliminary heat release of PACE-20, while typically overpredicting ignition delay times for PACE-1, PACE-8 and PRF88.4 at high-pressure and low-temperature/NTC conditions. Sensitivity and rate of production (ROP) analyses highlight surrogate-to-surrogate differences in the governing chemical kinetics where n-pentane initiates rapid OH branching at a faster rate and an earlier timing for PACE-20 than iso-pentane does for PACE-1 and PACE-8, making it computationally more reactive than the other surrogates. The current study highlights the need to include non-standardized properties, such as the lean/HCCI-like autoignition characteristics, in addition to ASTM properties (e.g., RON, MON) as metrics of fuel reactivity and targets to be matched when formulating high-fidelity surrogates that fully capture gasoline advanced combustion behavior such as HCCI-like autoignition.

42 ENGINEERING↗

Combustion characteristics and detailed simulations of surrogates for a Tier II gasoline certification fuel

An experimental and numerical study of combustion of a gasoline certification fuel (‘indolene’), and four (S4) and five (S5) component surrogates for it, is reported for the configurations of an isolated droplet burning with near spherical symmetry in the standard atmosphere, and a single cylinder engine designed for advanced compression ignition of pre-vaporized fuel. The intent was to compare performance of the surrogate for these different combustion configurations and to assess the broader applicability of the kinetic mechanism and property database for the simulations. A kinetic mechanism comprised of 297 species and 16,797 reactions was used in the simulations that included soot formation and evolution, and accounted for unsteady transport, liquid diffusion inside the droplet, radiative heat transfer, and variable properties. The droplet data showed a clear preference for the S5 surrogate in terms of burning rate. The simulations showed generally very good agreement with measured droplet, flame, and soot shell diameters. Measurements of combustion timing, in-cylinder pressure, and mass-averaged gas temperature were also well predicted with a slight preference for the S5 surrogate. Preferential vaporization was not evidenced from the evolution of droplet diameter but was clearly revealed in simulations of the evolution of mixture fractions inside the droplets. Here, the influence of initial droplet diameter (D o ) on droplet burning was strong, with S5 burning rates decreasing with increasing D o due to increasing radiation losses from the flame. Flame extinction was predicted for D o =3.0 mm as a radiative loss mechanism but not predicted for smaller D o for the conditions of the simulations.

42 ENGINEERING↗

Fuel and fuel blend for internal combustion engine

A fuel or fuel blending agent for an internal combustion engine includes a ketone compound that is a C 4 to C 10 branched acyclic ketone, cyclopentanone, or a derivative of cyclopentanone. The ketone compound may be blended with a majority portion of a fuel selected from the group consisting of: gasoline, diesel, alcohol fuel, biofuel, renewable fuel, Fischer-Tropsch fuel, or combinations thereof. The ketone compound may be derived from biological sources. A method for powering an internal combustion engine with a fuel comprising the ketone compound is also provided.

Dec, John E.↗

Simulating combustion of a seven-component surrogate for a gasoline/ethanol blend including soot formation and comparison with experiments

Combustion of a seven-component surrogate for a research grade 87 octane gasoline mixed with 10% ethanol is investigated experimentally and numerically from the perspective of an isolated droplet burning under conditions that promote one-dimensional gas transport. The numerical analysis included a kinetic mechanism comprised of 398 species and 24,814 reactions and a soot model that accounted for nucleation, surface growth, coalescence/aggregation of soot particles, and luminous flame radiation. Measurements of droplet and flame diameters were made for an initial droplet diameter (D o ) of approximately 0.63 mm. The simulations agreed well with the measurements including the location of the soot shell. Preferential vaporization was revealed by simulations of the liquid concentrations in the droplet. Predicted peak soot volume fractions coincided with temperatures between 1300 K and 1400 K as a soot inception temperature. Simulations were also carried out for D o between 0.25 mm and 5 mm to explore the effect of radiation and D o on burning. Below 0.25 mm radiation was negligible and burning rates and flame temperatures converged to a single value. Increasing D o up to 1.8 mm lowered the burning rate with luminous radiation having a strong effect. When radiation was entirely removed from the model the burning rate was nearly constant. Above D o = 2 mm droplets extinguished almost immediately after ignition. The flame temperature decreased with increasing D o while it increased when radiation was omitted. As a result, the simulations show that soot precursors including polyaromatic hydrocarbons were concentrated around the soot shell.

42 ENGINEERING↗

Advanced Engine and Fuel Technologies Annual Progress Report (FY2019)

On behalf of the Vehicle Technologies Office of the U.S. Department of Energy, we are pleased to introduce the Fiscal Year (FY) 2019 Annual Progress Report for the Advanced Engine and Fuel Technologies Program. In support of the Vehicle Technology Office’s goal for future U.S. economic growth, the Program focuses on early-stage research and development to improve understanding of combustion processes, fuel properties, and emissions control technologies, generating knowledge and insight necessary for industry to cost-effectively develop the next generation of engines and fuels. One of the most promising and cost-effective approaches to improving the fuel economy of the U.S. vehicle fleet is to introduce the next generation of higher-efficiency, very-low-emission combustion engines that meet future federal emissions regulations into the passenger and commercial vehicle markets. Advanced fuel formulations that can incorporate non-petroleum-based blending agents could further enhance engine efficiency, reduce greenhouse gas emissions, and provide fuel diversification. Also, innovations in combustion, fuels, emissions control, air control, turbomachinery, and energy recovery could potentially increase fuel economy considerably compared to today’s vehicles. The expected national economic, environmental, and energy security benefits from these next-generation engines and fuels would be significant inasmuch as the majority of vehicles sold over the next several decades will still include an engine. The Program has set the following goals for passenger and commercial vehicle fuel economy improvements. By 2030, increase light-duty engine efficiency to demonstrate 35% improvement in passenger vehicle fuel economy (25% improvement from engine efficiency and 10% from fuel co-optimization) relative to a 2015 baseline vehicle, while meeting the U.S. Environmental Protection Agency Tier 3 Emission and Fuel Standards. By 2030, improve heavy-duty engine efficiency by 35% relative to a 2009 baseline vehicle and identify cost-effective high-performance fuels that can further increase efficiency up to an additional 4%, while meeting prevailing U.S. Environmental Protection Agency emissions standards. The Program utilized advanced combustion processes to increase engine efficiency, resulting in a modeled passenger vehicle fuel economy improvement of 19.4% (over a Model Year 2015 baseline) in FY 2019. This report highlights progress achieved by the Advanced Engine and Fuel Technologies Program during FY 2019. The nature, current focus, and recent progress of the Program are described together with summaries of National Laboratory, industry, and university projects that provide an overview of the exciting work being conducted to address critical technical barriers and challenges to commercializing the next generation of higher-efficiency engine, emissions control, and fuel technologies for passenger and commercial vehicles.

33 ADVANCED PROPULSION SYSTEMS↗

Additive-mixing fuel-injection system for internal combustion engines

A system and method for fast control of the timing of combustion in an internal combustion engine, comprising actuating a fast-acting fuel-additive supply valve to meter a variable amount of fuel additive into a fuel stream, thereby forming an additive-enhanced fuel with an additive concentration that can be dynamically adjusted as fast as each engine cycle; injecting the additive-enhanced fuel directly or indirectly into a combustion chamber or into an intake port; and combusting the additive-enhanced fuel.

42 ENGINEERING↗

Co-Optimization of Fuels & Engines: Properties of Co-Optima Core Research Gasolines

The Co-Optima Core gasolines are a set of fuels developed to have similar autoignition properties but a wide range of composition. The primary compositional components varied were isoparaffins, cycloparaffins, olefins, aromatics, and ethanol. These fuels are being used extensively across the DOE national laboratories in fuel property and engine combustion research.They provide a consistent baseline across research platforms. This document is a compilation of chemical analysis and property data on these fuels, including basic properties such as density, octane numbers, heating value, Reid vapor pressure, and distillation. Elemental composition is reported, as well as detailed hydrocarbon analysis and functional group analysis by NMR spectroscopy. Enthalpy of vaporization at 20 deg C as well as true vapor pressure over the temperature range -20 deg to 120 deg C are also reported.

30 DIRECT ENERGY CONVERSION↗