Engineering topics

DeWeese, Keith

Publications and source records attributed to DeWeese, Keith.

6 records

NASA NTRS2016

Relative Terrain Imaging Navigation (RETINA) Tool for the Asteroid Redirect Robotic Mission (ARRM)

As a part of the NASA initiative to collect a boulder off of an asteroid and return it to Lunar orbit, the Satellite Servicing Capabilities Office (SSCO) and NASA GSFC are developing an on-board relative terrain imaging navigation algorithm for the Asteroid Redirect Robotic Mission (ARRM). After performing several flybys and dry runs to verify and refine the shape, spin, and gravity models and obtain centimeter level imagery, the spacecraft will descend to the surface of the asteroid to capture a boulder and return it to Lunar Orbit. The algorithm implements Stereophotoclinometry methods to register landmarks with images taken onboard the spacecraft, and use these measurements to estimate the position and orientation of the spacecraft with respect to the asteroid. This paper will present an overview of the ARRM GN&C system and concept of operations as well as a description of the algorithm and its implementation. These techniques will be demonstrated for the descent to the surface of the proposed asteroid of interest, 2008 EV5, and preliminary results will be shown.

Navigation↗

NASA NTRS2015

Linear Covariance Analysis For Proximity Operations Around Asteroid 2008 EV5

The NASA initiative to collect an asteroid the Asteroid Robotic Redirect Mission (ARRM) is currently investigating the option of retrieving a boulder off an asteroid, demonstrating planetary defense with an enhanced gravity tractor technique and returning it to a lunar orbit. Techniques for accomplishing this are being investigated by the Satellite Servicing Capabilities Office (SSOO) and NASA GSFC in colloboration with JPL, NASA, JSC, LaRC, and Draper Laboratories Inc. Two critical phases of the mission are the descent to the boulder and the Enhanced Gravity Tractor-enhanced gravity tractor demonstration. A linear covariance analysis was done for these phases to assess the feasibility of these concepts with the proposed design of the sensor and actuaor suite of the Asteroid Redirect Vehicle (ARV). The sensor suite for this analysis will include a wide field of view camera, Lidar, and a MMU. The proposed asteroid of interest is currently the C-type asteroid 2008 EV5, a carbonaceous chondrite that is of high interest to the scientific community. This paper will present an overview of the analysis discuss sensor and actuator models and address the feasibility of descending to the boulder within the requirements as the feasibility of maintaining the halo orbit in order to demonstrate the Enhanced Gravity Tractor-enhanced gravity tractory technique.

Guidance↗

NASA NTRS2015

Global Precipitation Measurement Mission Launch and Commissioning

During launch and early operation of the Global Precipitation Measurement (GPM) Mission, the Guidance, Navigation, and Control (GN&C) analysis team encountered four main on-orbit anomalies. These include: (1) unexpected shock from Solar Array deployment, (2) momentum buildup from the Magnetic Torquer Bars (MTBs) phasing errors, (3) transition into Safehold due to albedo induced Course Sun Sensor (CSS) anomaly, and (4) a flight software error that could cause a Safehold transition due to a Star Tracker occultation. This paper will discuss ways GN&C engineers identified the anomalies and tracked down the root causes. Flight data and GN&C on-board models will be shown to illustrate how each of these anomalies were investigated and mitigated before causing any harm to the spacecraft. On May 29, 2014, GPM was handed over to the Mission Flight Operations Team after a successful commissioning period. Currently, GPM is operating nominally on orbit, collecting meaningful scientific data that will significantly improve our understanding of the Earth's climate and water cycle.

Guidance Navigation and Control↗

NASA NTRS2012

Safehold Attitude Determination Approach for GPM

Spacecraft sating designs generally have minimal goals with loose pointing requirements. Safe pointing orientations for three-axis stabilized spacecraft are usually chosen to put the spacecraft into a thermally safe and power-positive orientation. In addition, safe mode designs are required to be simple and reliable. This simplicity lends itself to the usage of analog sun sensors, because digital sun sensors will add unwanted complexity to the safe hold mode. The Global Precipitation Measurement (GPM) Mission Core Observatory will launch into lower earth orbit (LEO) at an inclination of 65 degrees. The GPM instrument suite consists of an active radar system and a passive microwave imager to provide the next-generation global observations of rain and snow. The complexity and precision of these instruments along with the operational constraints of the mission result in tight pointing requirements during all phases of the mission. To ensure the instruments are not damaged during spacecraft safing, thermal constraints dictate that the solar pointing orientation must be maintained to better than 6.5 degrees. This requirement is outside the capabilities of a typical analog sun sensor suite, primarily due to the effects of Earth's albedo. To ensure mission success, a new analog sensor, along with the appropriate algorithms, is needed. This paper discusses the design issues involving albedo effects on spacecraft pointing and the development of a simple, low-cost analog sensor and algorithm that will address the needs of the GPM mission. In addition, the algorithms are designed to be easily integrated into the existing attitude determination software by using common interfaces. The sensor design is based on a heritage, commercial off-the-shelf analog sun sensors with a limited field-of-view to reduce the effects of Earth's albedo. High fidelity simulation results are presented that demonstrate the efficacy of the design.

Fitzpatrick, Henry↗

NASA NTRS2005

TRMM Re-Entry Planning: Attitude Determination and Control During Thruster Modes

The Tropical Rainfall Measuring Mission (TRMM) spacecraft has been undergoing design for a controlled re-entry to Earth. During simulation of the re-entry plan, there was evidence of errors in the attitude determination algorithms during thruster modes. These errors affected the bum efficiency, and thus planning, during re-entry. During thruster modes, the spacecraft attitude is controlled off of integrated Gyro Error Angles that were designed to closely follow the nominal spacecraft pointing frame (Tip Frame). These angles, however, were not exactly mapped to the Tip Frame from the Body Frame. Additionally, in the initial formulation of the thruster mode attitude determination algorithms, several assumptions and approximations were made to conserve processor speed. These errors became noticeable and significant when simulating bums of much longer duration (-10 times) than had been produced in flight. A solution is proposed that uses attitude determination information from a propagated extended Kalman filter that already exists in the TRMM thruster modes. This attitude information is then used to rotate the Gyro Error Angles into the Tip Frame. An error analysis is presented that compares the two formulations. The new algorithm is tested using the TRMM High-Fidelity Simulator and verified with the TRMM Software Testing and Training Facility. Simulation results for both configurations are also presented.

DeWeese, Keith↗

NASA NTRS2004

Arc-Second Pointer for Balloon-Borne Astronomical Instrument

A control system has been designed to keep a balloon-borne scientific instrument pointed toward a celestial object within an angular error of the order of an arc second. The design is intended to be adaptable to a large range of instrument payloads. The initial payload to which the design nominally applies is considered to be a telescope, modeled as a simple thin-walled cylinder 24 ft (approx.= 7.3 m) long, 3 ft (approx.= 0.91 m) in diameter, weighing 1,500 lb (having a mass of .680 kg). The instrument would be mounted on a set of motor-driven gimbals in pitch-yaw configuration. The motors on the gimbals would apply the control torques needed for fine adjustments of the instrument in pitch and yaw. The pitch-yaw mount would, in turn, be suspended from a motor mount at the lower end of a pair of cables hanging down from the balloon (see figure). The motor in this mount would be used to effect coarse azimuth control of the pitch-yaw mount. A notable innovation incorporated in the design is a provision for keeping the gimbal bearings in constant motion. This innovation would eliminate the deleterious effects of static friction . something that must be done in order to achieve the desired arc-second precision. Another notable innovation is the use of linear accelerometers to provide feedback that would facilitate the early detection and counteraction of disturbance torques before they could integrate into significant angular-velocity and angular-position errors. The control software processing the sensor data would be capable of distinguishing between translational and rotational accelerations. The output of the accelerometers is combined with that of angular position and angular-velocity sensors into a proportional + integral + derivative + acceleration control law for the pitch and yaw torque motors. Preliminary calculations have shown that with appropriate gains, the power demand of the control system would be low enough to be satisfiable by means of storage batteries charged by solar batteries during the day.

Ward, Philip R.↗