Engineering topics

DeMange, Jeffrey J.

Publications and source records attributed to DeMange, Jeffrey J..

30 records · Page 2

NASA NTRS2004

Oxidation of High-temperature Alloy Wires in Dry Oxygen and Water Vapor

Small diameter wires (150 to 250 microns) of the high temperature alloys Haynes 188, Haynes 230, Haynes 230, Haynes 214, Kanthal Al and PM2000 were oxidized at 1204 C in dry oxygen or 50% H2O /50% O2 for 70 Hours. The oxidation kinetics were monitored using a thermogravimetric technique. Oxide phase composition and morphology of the oxidized wires were determined by X-ray diffraction,field emission scanning electron microscopy, and energy dispersive spectroscopy. The alumina-forming alloys, Kanthal Al and PM2000, out-performed the chromia-forming alloys under this conditions. PM2000 was recommended as the most promising candidate for advanced hybrid seal applications for space reentry control surface seals or hypersonic propulsion system seals. This study also demonstrated that thermogravimetric analysis of small diameter wires is a powerful technique for the study of oxide volatility, oxide adherence, and breakaway oxidation.

Opila, Elizabeth J.↗

NASA NTRS2003

Advanced Control Surface Seal Development for Future Space Vehicles

NASA's Glenn Research Center (GRC) has been developing advanced high temperature structural seals since the late 1980s and is currently developing seals for future space vehicles as part of the Next Generation Launch Technology (NGLT) program. This includes control surface seals that seal the edges and hinge lines of movable flaps and elevons on future reentry vehicles. In these applications, the seals must operate at temperatures above 2000 F in an oxidizing environment, limit hot gas leakage to protect underlying structures, endure high temperature scrubbing against rough surfaces, and remain flexible and resilient enough to stay in contact with sealing surfaces for multiple heating and loading cycles. For this study, three seal designs were compared against the baseline spring tube seal through a series of compression tests at room temperature and 2000 F and flow tests at room temperature. In addition, canted coil springs were tested as preloaders behind the seals at room temperature to assess their potential for improving resiliency. Addition of these preloader elements resulted in significant increases in resiliency compared to seals by themselves and surpassed the performance of the baseline seal at room temperature. Flow tests demonstrated that the seal candidates with engineered cores had lower leakage rates than the baseline spring tube design. However, then the seals were placed on the preloader elements, the flow rates were higher as the seals were not compressed as much and therefore were not able to fill the groove as well. High temperature tests were also conducted to assess the compatability of seal fabrics against cermaic matrix composite (CMC) panels anticipated for use in next generation launch vehicles. These evaluations demonstrated potential bonding issues between the Nextel fabrics and CMC candidates.

DeMange, Jeffrey J.↗

NASA NTRS2003

High Temperature Propulsion System Structural Seals for Future Space Launch Vehicles

Durable, flexible sliding seals are required in advanced hypersonic engines to seal the perimeters of movable engine ramps for efficient, safe operation in high heat flux environments at temperatures of 2000 to 2500 F. Current seal designs do not meet the demanding requirements for future engines, so NASA's Glenn Research Center is developing advanced seals and preloading devices to overcome these shortfalls. An advanced ceramic wafer seal design and two types of seal preloading devices were evaluated in a series of compression, scrub, and flow tests. Silicon nitride wafer seals survived 2000 in. (1000 cycles) of scrubbing at room temperature against an Inconel 625 rub surface with no chips or signs of damage. Flow rates measured for the wafers before and after scrubbing were almost identical and were much lower than those recorded for the best braided rope seal flow blockers. Canted coil springs and silicon nitride compression springs showed promise conceptually as potential seal preloading devices to help maintain seal resiliency. A finite element model of the canted coil spring revealed that it should be possible to produce a spring out of high temperature materials for applications at 2000+ F.

Dunlap, Patrick H., Jr.↗

NASA NTRS2003

Third Generation RLV Structural Seal Development Programs at NASA GRC

NASA is currently developing technologies for the 3rd Generation Reusable Launch Vehicle (RLV) that is being designed to enter service around the year 2025. In particular, NASA's Glenn Research Center (GRC) is working on advanced high temperature structural seal designs including propulsion system and control surface seals. Propulsion system seals are required along the edges of movable panels in advanced engines, while control surface seals seal the edges and hinge lines of movables flaps and elevons on the vehicle. The overall goal is to develop reusable, resilient seals capable of operating at temperatures up to 2000 F. High temperature seal preloading devices (e.g., springs) are also being evaluated as a means of improving seal resiliency. In order to evaluate existing and potential new seal designs, GRC has designed and is installing several new test rigs capable of simulating the types of conditions that the seals would endure during service including temperatures, pressures, and scrubbing. Two new rigs, the hot compression test rig and the hot scrub test rig, will be used to perform seal compression and scrub tests for many cycles at temperatures up to 3000 F. Another new test rig allows simultaneous flow and scrub tests to be performed on the seals at room temperature to evaluate how the flow blocking performance of the seals varies as they accumulate damage during scrubbing. This presentation will give an overview of these advanced seal development efforts.

Dunlap, Patrick H., Jr.↗

NASA NTRS2003

Update on the Development and Capabilities of Unique Structural Seal Test Rigs

High temperature structural seals are necessary in many aerospace and aeronautical applications to minimize any detrimental effects originating from undesired leakage. The NASA Glenn Research Center has been and continues to be a pioneer in the development and evaluation of these types of seals. The current focus for the development of structural seals is for the 3rd Generation Reusable Launch Vehicle (RLV), which is scheduled to replace the current space shuttle system by 2025. Specific areas of development under this program include seals for propulsion systems (such as the hypersonic air-breathing ISTAR engine concept based upon Rocket Based Combined Cycle technology) and control surface seals for spacecraft including the autonomous rescue X-38 Crew Return Vehicle and the X-37 Space Maneuver Vehicle.

DeMange, Jeffrey J.↗

NASA NTRS2003

Overview of NASA Glenn Seal Program

The Seal Team is divided into four primary areas. These areas include turbine engine seal development, structural seal development, acoustic seal development, and adaptive seal development. The turbine seal area focuses on high temperature, high speed shaft seals for secondary air system flow management. The structural seal area focuses on high temperature, resilient structural seals required to accommodate large structural distortions for both space- and aero-applications. Our goal in the acoustic seal project is to develop non-contacting, low leakage seals exploiting the principles of advanced acoustics. We are currently investigating a new acoustic field known as Resonant Macrosonic Synthesis (RMS) to see if we can harness the large acoustic standing pressure waves to form an effective air-barrier/seal. Our goal in the adaptive seal project is to develop advanced sealing approaches for minimizing blade-tip (shroud) or interstage seal leakage. We are planning on applying either rub-avoidance or regeneration clearance control concepts (including smart structures and materials) to promote higher turbine engine efficiency and longer service lives.

Steinetz, Bruce M.↗

NASA NTRS2003

Advanced Control Surface Seal Development at NASA GRC for Future Space Launch Vehicles

NASA s Glenn Research Center (GRC) is developing advanced control surface seal technologies for future space launch vehicles as part of the Next Generation Launch Technology project (NGLT). New resilient seal designs are currently being fabricated and high temperature seal preloading devices are being developed as a means of improving seal resiliency. GRC has designed several new test rigs to simulate the temperatures, pressures, and scrubbing conditions that seals would have to endure during service. A hot compression test rig and hot scrub test rig have been developed to perform tests at temperatures up to 3000 F. Another new test rig allows simultaneous seal flow and scrub tests at room temperature to evaluate changes in seal performance with scrubbing. These test rigs will be used to evaluate the new seal designs. The group is also performing tests on advanced TPS seal concepts for Boeing using these new test facilities.

Dunlap, Patrick H., Jr.↗

NASA NTRS2002

Advanced Control Surface Seal Development at NASA GRC for 3rd Generation RLV

NASA's Glenn Research Center (GRC) is developing advanced control surface seal technologies for the 3rd Generation RLV program. GRC has designed several new test rigs to simulate the temperatures, pressures, and scrubbing conditions that seals would have to endure during service. A hot compression test rig and hot scrub test rig are being developed to perform tests at temperatures up to 3000 F. Another new test rig allows simultaneous seal flow and scrub tests at room temperature to evaluate changes in seal performance with scrubbing. High temperature ceramic preloading devices are being developed and evaluated as ways to improve seal resiliency.

Dunlap, Patrick H., Jr.↗

NASA NTRS2002

Overview of NASA Glenn Seal Program

NASA Glenn hosted the Seals/Secondary Air System Workshop on October 30-31, 2001. Each year NASA and our industry and university partners share their respective seal technology developments. We use these workshops as a technical forum to exchange recent advancements and "lessons-learned" in advancing seal technology and solving problems of common interest. As in the past we are publishing two volumes. Volume I will be publicly available and individual papers will be made available on-line through the web page address listed at the end of this chapter. Volume II will be restricted under International Traffic and Arms Regulations (I.T.A.R.) and/or Export Administration Regulations (E.A.R.).

Steinetz, Bruce M.↗

NASA NTRS2002

Third Generation RLV Structural Seal Development Programs at NASA GRC

NASA GRC's work on high temperature structural seal development began in the late 1980's and early 1990's under the NASP (National Aero-Space Plane) project. Bruce Steinetz led the in-house propulsion system seal development program and oversaw industry efforts for propulsion system and airframe seal development for this vehicle. a propulsion system seal location in the NASP engine is shown. The seals were located along the edge of a movable panel in the engine to seal the gap between the panel and adjacent engine sidewalls. More recently, we worked with Rocketdyne on high temperature seals for the linear aerospike engine ramps. In applications such as the former X-33 program, multiple aerospike engine modules would be installed side by side on the vehicle. Seals are required in between adjacent engine modules along the edges and base of the engines. The seals have to withstand the extreme temperatures produced byt he thrusters at the top of the ramps while accommodating large deflections between adjacent ramps. We came up with several promising seal concepts for this application and shared them with Rocketdyne.

Dunlap, Patrick H., Jr.↗

NASA NTRS2002

Development and Capabilities of Unique Structural Seal Test Rigs

High temperature structural seals are necessary in many aerospace and aeronautical applications to minimize any detrimental effects originating from undesired leakage. The NASA Glenn Research Center has been and continues to be a pioneer in the development and evaluation of these types of seals. The current focus for the development of structural seals is for the 3rd Generation Reusable Launch Vehicle (RLV), which is scheduled to replace the current space shuttle system around 2025. Specific areas of development under this program include seals for propulsion systems (such as the hypersonic air-breathing ISTAR engine concept based upon Rocket Based Combined Cycle technology) and control surface seals for spacecraft including the autonomous rescue X-38 Crew Return Vehicle and the X-37 Space Maneuver Vehicle.

DeMange, Jeffrey J.↗

NASA NTRS2002

Investigations of Control Surface Seals for Re-entry Vehicles

Re-entry vehicles generally require control surfaces (e.g., rudders, body flaps) to steer them during flight. Control surface seals are installed along hinge lines and where control surface edges move close to the vehicle body. These seals must operate at high temperatures and limit heat transfer to underlying structures to prevent them from overheating and causing possible loss of vehicle structural integrity. This paper presents results for thermal analyses and mechanical testing conducted on the baseline rudder/fin seal design for the X-38 re-entry vehicle. Exposure of the seals in a compressed state at the predicted peak seal temperature of 1900 F resulted in loss of seal resiliency. The vertical Inconel rudder/fin rub surface was re-designed to account for this loss of resiliency. Room temperature compression tests revealed that seal unit loads and contact pressures were below limits set to protect Shuttle thermal tiles on the horizontal sealing surface. The seals survived an ambient temperature 1000 cycle scrub test over sanded Shuttle tiles and were able to disengage and re-engage the tile edges during testing. Arc jet tests confirmed the need for seals in the rudder/fin gap location because a single seal caused a large temperature drop (delta T = 1710 F) in the gap.

Dunlap, Patrick H., Jr.↗