A Method for Quantifying Crossover in Redox Flow Cells through Compositionally Unbalanced Symmetric Cell Cycling
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Darling, Robert M..
Explore the source record for details and available documents.
Here, reducing platinum (Pt) loading in polymer electrolyte fuel cells (PEFCs) while meeting performace requirements is critical to their widespread deployment. However, significant polarization losses manifest at higher current densities in cathodes with lower Pt content. The morphology of the carbon supports in PEFC cathodes affects the location of Pt deposition into the micropits or onto the surface of the carbon support, translating into different kinetic and transport resistances. In this work, we derive an agglomerate scale model that differentiates the sink terms for Pt on the surface and in the pits of carbon supports. We develop an approach to assess the impact of nanoscale ohmic resistance to Pt in the micropits arising from weakly ionic solution in the carbon support on PEFC performance. Effectiveness factors relating the actual reaction rate to the maximum reaction rate (had all the Pt been exposed) are derived and embedded into a one-dimensional catalyst layer model. Parameters in the catalyst layer model are tuned based on experimental local oxygen transport resistances. Subsequently, we estimate bounds for the micropore resistances based on geometric and physical arguments. Lastly, polarization curves are simulated to assess the effect of the micropore resistance in fully-humidified and oxygen-rich environments.
Development of inexpensive long-duration energy storage supports widespread deployment of variable renewable energy resources onto the electricity grid. Flow batteries are a promising class of devices for long-duration energy storage. Techno-economic modeling is needed to evaluate commercial feasibility of existing technologies and to help guide research and development of new technologies. Levelized cost of storage is a useful metric that accounts for capital and operating costs and energy throughput over the life of a project. This metric is used to compare the economic prospects of lithium ion to eight aqueous and two hypothetical nonaqueous flow batteries in four use cases. Finally, flow batteries with inexpensive active materials are favored in long-duration applications.
Fluxes of negatively charged ligand-coordinated iron, Fe(CN) 6 3/4- , and chromium, CrPDTA 1/2− , through two promising commercial cation-exchange membranes, Aquivion E87–05S and Fumasep E-620(K), were measured as functions of current density. The magnitude of the partial current density reached a maximum of − 43 μ A cm −2 at the maximum applied current density magnitude of − 43 mA cm −2 for Fe(CN) 6 3/4− transport through Aquivion, or 0.1% of the total current density. Fumasep E-620(K) blocks practically all crossover of both compounds. Both membranes sorb more Fe(CN) 6 3/4− and CrPDTA 1/2− than predicted by Donnan equilibrium, and low crossover rates can be attributed mainly to slow diffusion, not charge-based rejection of co-ions. The magnitude of the diffusion coefficient appears to correlate with hydraulic permeability. Although Aquivion E87–05S and Fumasep E-620(K) have significant and observable differences in membrane crossover rates, cells built with the DI-soaked membranes offer similarly high coulombic efficiency, indicating the relatively small contribution that crossover makes to inefficiency over a single cycle.
Fluxes of negatively charged, neutral, and positively charged vanadium acetylacetonates through the cation-exchange membrane Nafion® 211 were measured as functions of current density. Fluxes increase in order V(C 5 H 7 O 2 ) 3 – < V(C 5 H 7 O 2 ) 3 0 < V(C 5 H 7 O 2 ) 3 + as expected for a membrane with fixed negative charges. Furthermore, the dependence of these fluxes on current density is quantitatively consistent with predictions made using independently measured conductivities in Nernst-Planck-Einstein transport equations. However, differences between the three fluxes are smaller than predicted by Donnan equilibrium calculations for Nafion 211 immersed in V(C 5 H 7 O 2 ) 3 solutions. Furthermore, specific interactions between sorbed species appear to be responsible for the relatively rapid transport of V(C 5 H 7 O 2 ) 3 – compared to V(C 5 H 7 O 2 ) 3 + .
A new set of equations describing Donnan equilibrium predicts that increased Donnan exclusion in charged polymer networks can occur at high salt concentrations.
Explore the source record for details and available documents.
A new flow battery is presented using the abundant and inexpensive active material pairs permanganate/manganate and disulfide/tetrasulfide. A wetted material set is identified for compatibility with the strongly oxidizing manganese couple at ambient and elevated temperatures. Both solutions allow high active material solubility, with cells tested at theoretical energy densities up to 43 Wh l −1 for the ∼1.2 V cell. Full cells built with nickel foam electrodes and sodium-exchanged Nafion 115 membranes deliver a baseline area-specific resistance of 2.7 Ω-cm 2 . Incorporation of high-surface-area cobalt-coated carbon paper and high-surface-area stainless steel mesh electrodes, and an expanded Nafion 115 membrane delivers cells with 44% lower resistance at 1.6 Ω-cm 2 . All cells show performance decay over the course of cycling. The Co-decorated carbon paper electrodes provide significant kinetic improvements, shifting electrode performance from non-linear with Ni-foam to linear with a volume-normalized exchange current density value of 3.2 A cm −3 . The expanded membrane provides increased conductivity over the 13 mS cm −1 conductivity observed in as-received, sodium-exchanged Nafion 115. Although boiled membranes provide improved conductivity, it is at the cost of decreased Coulombic efficiency and poorer manufacturability. Full cell models suggest that similar cell resistances (1.7 Ω-cm 2 ) should be feasible with as-received Nafion 115 and advanced electrodes.
Raytheon Technologies Research Center (RTRC) in collaboration with Ion Power Inc. and the University of Arkansas at Little Rock and the FC-PAD consortium executed a project that: (1) developed comprehensive models of oxygen and proton transport in cathode catalyst layers that provided new insights about losses associated with reducing platinum loading to 0.1 mg/cm 2 , (2) designed, fabricated, characterized, and tested cells featuring carbon-supported catalyst layers with low platinum loadings that met efficiency and power density targets set forth by the Hydrogen and Fuel Cells Technology Office, and (3) designed, fabricated, characterized, and tested novel catalyst structures. The modeling efforts produced eight scientific publications that shared new descriptions of oxygen and proton transport in catalyst layers with the broader technical community. The key physical insights from the models are expressed in straightforward algebraic expressions, facilitating easy adoption by other researchers. The models developed during the project explain why resistance to oxygen transport is inversely proportional to interfacial area of platinum – an observation that eluded quantitative explanation for a decade. The models quantitatively predict polarization when measured morphological parameters and transport properties are input. Membrane-electrode assemblies made during the project met stated goals for current at high voltage and power density at rated voltage for transportation fuel cells at the end of budget period 2. High performance was achieved by developing a diffusion layer with low resistance to oxygen transport and a PtCo/C cathode catalyst layer capable of supporting rapid proton and oxygen transport. The project was subsequently directed to curtail experimental work and focus on modeling during budget period 3. Ion Power Inc. developed new expertise in fabricating catalyst layers containing platinum-cobalt catalysts, and processing very thin membranes. The University of Arkansas at Little Rock developed novel nanocolumnar self-supported thin film electrocatalysts that can be grown on carbon supports using a simple high pressure sputter deposition method. The nanocolumnar microstructure provides adequate surface-to-volume ratio for efficient platinum utilization, and the conformal platinum shell with larger crystal grain sizes covering the carbon support surface may eliminate durability issues associated with catalyst dissolution, agglomeration, and carbon corrosion.
Explore the source record for details and available documents.
An analytical model for a blocking porous electrode is derived and used to predict how ohmic resistance inside micropores that host catalyst nanoparticles affects impedance. This paper revisits a widely used approach for estimating ionic conductivities of catalyst layers in fuel cells. An interfacial term associated with resistance in micropores is derived and added to the classical expression for the impedance of a blocking porous electrode at low frequency. The revised model predicts a physically realistic rise in the real component of the impedance at low frequency when reasonable pore dimensions and conductivities are used as inputs.
Here, an analytical model for resistance to oxygen transport in air electrodes containing carbon black supports with high surface area was developed by combining a Thiele modulus—effectiveness factor approach at the agglomerate scale (~150 nm) with nanoscale diffusional resistance in carbon micropores/pits (~5 nm). This paper extends an earlier model for transport resistance to platinum nanoparticles on low surface area carbon. Differences in transport resistances between catalyst layers with high and low surface area carbon blacks predicted by the model with reasonable geometric dimensions and physical properties are consistent with experimental observations.
Not Available
Explore the source record for details and available documents.
A model of a fuel-cell cathode with distinct proton conductivities at the agglomerate and electrode scales was used to simulate polarization curves under conditions with facile oxygen transport. Here, the model was applied to electrodes containing agglomerates with different ratios of platinum to carbon in order to examine the hypothesis that intra-agglomerate proton conductivity is substantially lower than ionomer conductivity. The model predicts decreasing performance and increasing sensitivity to Pt/C ratio as intra-agglomerate conductivity declines relative to a constant through-electrode conductivity. Experiments on catalyst layers with Vulcan supports do not show the predicted trend indicating that mesoscale intra-agglomerate conductivity is not orders of magnitude lower than bulk ionomer conductivity.
Not Available
Not Available