Engineering topics

Daniel E. Paxson

Publications and source records attributed to Daniel E. Paxson.

5 records

NASA NTRS2023

Variably Premixed Rotating Detonation Engine for Evaluation of Detonation Cycle Dynamics

A variably premixed rotating detonation engine using gaseous hydrogen and air reactants is introduced to enable investigation of key cycle processes while varying the homogeneity of the reactant inlet conditions. Two chamber configurations are investigated, the first with reactants filling the entire span of a straight annular channel and the second with a slightly larger channel and a backward-facing step. The first configuration permits both premixed and non-premixed fuel injection, enabling mixing quality modulation. The second configuration is operated only at fully premixed conditions. Operating modes and detonation wave speeds are characterized using exhaust-plume imaging, while the chamber heat release field is captured by transverse imaging through a transparent outer body. Tests using the first configuration were characterized by unstable counterpropagating modes with low detonation wave speeds regardless of the state of premixing, while the second configuration rendered single-wave behavior with wave speeds up to 86% of the Chapman–Jouguet velocity. Comparisons with a simple computational fluid dynamics model of the second configuration indicate that reactant preheating significantly influences the detonation wave topology, highlighting the potential utility of the test platform for isolating key physics associated with the effects of reactant premixing, preheating, and chamber geometry on rotating detonation engine operation.

Detonation↗

NASA NTRSDate not supplied

RDE Nozzle Computational Design Methodology Development and Application

The rotating detonation engine (RDE) is currently under investigation as an approach to achieving pressure gain combustion for propulsion and power systems. The RDE typically consists of an annulus with one end open (or having a throat and/or nozzle) and the other end valved using non-mechanical, fluidic means. In this study, a total of 6 nozzle design variations were studied for the NPS combustor geometry, using the validated quasi-2D to 3-D coupled simulation approach.

CFD↗

NASA NTRSDate not supplied

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

The performance impact of flow reversal at the inlet of an airbreathing rotating detonation engine (RDE) is investigated using 2 and 3-dimensional computational fluid dynamic (CFD) simulations. Flow reversal, or backflow, occurs in RDE inlets in the high-pressure region directly behind the rotating detonation front. This is also where most of the engine thrust or pressure gain is produced. The amount of backflow relative to throughflow depends on the inlet design. For the present work, a simple annular ‘slit’ design is used. The simulations are idealized in several ways, including that fuel and air are premixed, but prevented from reacting when within the inlet region. The results indicate that even with idealizations, the impact of inlet backflow on pressure gain can be substantial. The simulations also reveal an intriguing instability that develops in certain configurations. The mass flow rate into the RDE begins to oscillate at a regular frequency that is substantially less than the detonation rotational frequency. This is accompanied by oscillations in the detonation height. The oscillation amplitude grows over time until the detonation ultimately fails. Both the performance and instability results emphasize the need for carefully designed RDE inlets that provide low loss when flow is in the forward direction, but high resistance when the flow is reversed. Development of such high-diodicity inlets is critical to achieving pressure gain in airbreathing RDE’s.

detonation↗

NASA NTRSDate not supplied

Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle

A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.

detonation↗

NASA NTRSDate not supplied

Experimental and Computational Investigation of Valve Motion in a Resonant Pulse Combustor

The motion of a passive reed-type valve and a poppet-style valve operating in a small scale, liquid-fueled pulse combustor is investigated experimentally. Valve position and combustion chamber pressure are simultaneously measured using an in-house fabricated optical position probe. The reed valve configuration is found to operate in a self-aspirated mode, generating significant pressure gain. The poppet valve configuration cannot operate without forced air, and does not generate pressure gain. Both type valves are tested in combustors of multiple lengths. Close examination of the respective valve motions indicate that the reed valve is highly non-linear, with unique attributes that appear essential for self-aspiration. Dynamic models for the motion of each valve are implemented in a computational fluid dynamic (CFD) simulation of the pulse combustor in order to assess if this unique valve motion is critical to successful operation. The results show that it is. The implications of these results are discussed. The need for active actuation with feedback control, rather than passive valve actuation is highlighted as a critical technology for practical resonant pulse combustors.

Combustion↗