Engineering Papers⌕ Search

Engineering topics

Damiano, Brian

Publications and source records attributed to Damiano, Brian.

Deflection Shape Balancing: An Alternative to Modal Balancing

Rotor balancing is the final step in the rotor manufacturing process and may be necessary during rotor refurbishment. The process can be time consuming and costly, especially for supercritical monolithic rotors, impacting schedule and increasing costs. Modal balancing is a commonly used practice and is effective but requires multiple runs and at least one high-speed run. Deflection shape balancing is introduced as an alternative that may offer a more efficient method of balancing making the process faster with potentially fewer balancing runs. This paper explores the performance of the deflection shape fit balancing technique by utilizing MATLAB code simulations.

Morrell, William Jason↗

Method for Selecting Rotor Suspension Design Criteria

A method for selecting rotor suspension design criteria that allow rotors with internal friction to negotiate critical speeds and avoid subsynchronous internal friction instabilities is described. A rotor model of a test rotor with internal friction is created and used to calculate the test rotor’s critical speeds, mode shapes, Campbell plots, and the rotational speed corresponding to the stability boundary for a nominal set of suspension parameters. The test rotor model is then used to demonstrate the suspension design criteria selection method.

Damiano, Brian↗

Estimating Rotor Suspension Parameters from Runout Data

Determining the dynamic characteristics of rotor suspensions is needed to make accurate predictions of rotor behavior. If direct measurements are unavailable, a method for estimating them is needed. This paper describes a method for estimating suspension characteristics from rotor runout data measured by proximity probes in a rotor test stand. Comparison of measured critical speeds with values predicted using the estimated rotor suspension parameters for a test rotor show good agreement, indicating that the method is valid.

Damiano, Brian↗

Two-Year Operational Evaluation Of A Consumer Electronics-Based Data Acquisition System For Equipment Monitoring

Oak Ridge National Laboratory (ORNL) has performed a two-year evaluation of the performance of an in-house developed consumer electronics-based data acquisition system (DAS). The main advantage of this approach compared to conventional instrumentation grade systems is cost; instrument grade data acquisition systems average costs range from $800 to $2,000 per channel compared to a range of $200 - $400 per channel for a consumer electronics-based system. The DAS is operated as a full-time in-situ vibration monitor. The resulting data stream is streamed over the ORNL network, at an aggregate rate of approximately 2 megabytes/s, to a Linux server. The server includes the capability to implement event-triggered data stores, as well as real-time files for the implementation of continuous display monitoring of the spectra. Detailed spectral analysis is performed post event. The DAS is installed on a large industrial chiller and cooling water pump associated with ORNL’s Titan supercomputer. These mechanical systems include rotating components that operate at fundamental frequencies within the range of 30 Hz to over 3 KHz. Evaluation of the DAS data over a two-year operating period leads to the conclusion that for many industrial processes this system could form the basis for a cost effective means of obtaining operating health data in real time from rotating machinery. The deployment has also shown that the DAS technology is reliable. Furthermore, because the cost of the DAS is low, the other significant advantage of this approach is that the DAS can be deployed in a dedicated manner and operated on a full-time basis.

Wetherington Jr, G↗

In-situ Condition Monitoring of Components in Small Modular Reactors Using Process and Electrical Signature Analysis. Final report, volume 1. Development of experimental flow control loop, data analysis and plant monitoring

The research and development under this project was focused on the following three major objectives: Objective 1: Identification of critical in-vessel SMR components for remote monitoring and development of their low-order dynamic models, along with a simulation model of an integral pressurized water reactor (iPWR). Objective 2: Development of an experimental flow control loop with motor-driven valves and pumps, incorporating data acquisition and on-line monitoring interface. Objective 3: Development of stationary and transient signal processing methods for electrical signatures, machinery vibration, and for characterizing process variables for equipment monitoring. This objective includes the development of a data analysis toolbox. The following is a summary of the technical accomplishments under this project: - A detailed literature review of various SMR types and electrical signature analysis of motor-driven systems was completed. A bibliography of literature is provided at the end of this report. Assistance was provided by ORNL in identifying some key references. - A review of literature on pump-motor modeling and digital signal processing methods was performed. - An existing flow control loop was upgraded with new instrumentation, data acquisition hardware and software. The upgrading of the experimental loop included the installation of a new submersible pump driven by a three-phase induction motor. All the sensors were calibrated before full-scale experimental runs were performed. - MATLAB-Simulink model of a three-phase induction motor and pump system was completed. The model was used to simulate normal operation and fault conditions in the motor-pump system, and to identify changes in the electrical signatures. - A simulation model of an integral PWR (iPWR) was updated and the MATLAB-Simulink model was validated for known transients. The pump-motor model was interfaced with the iPWR model for testing the impact of primary flow perturbations (upsets) on plant parameters and the pump electrical signatures. Additionally, the reactor simulation is being used to generate normal operation data and data with instrumentation faults and process anomalies. A frequency controller was interfaced with the motor power supply in order to vary the electrical supply frequency. The experimental flow control loop was used to generate operational data under varying motor performance characteristics. Coolant leakage events were simulated by varying the bypass loop flow rate. The accuracy of motor power calculation was improved by incorporating the power factor, computed from motor current and voltage in each phase of the induction motor.- A variety of experimental runs were made for steady-state and transient pump operating conditions. Process, vibration, and electrical signatures were measured using a submersible pump with variable supply frequency. High correlation was seen between motor current and pump discharge pressure signal; similar high correlation was exhibited between pump motor power and flow rate. Wide-band analysis indicated high coherence (in the frequency domain) between motor current and vibration signals. - Wide-band operational data from a PWR were acquired from AMS Corporation and used to develop time-series models, and to estimate signal spectrum and sensor time constant. All the data were from different pressure transmitters in the system, including primary and secondary loops. These signals were pre-processed using the wavelet transform for filtering both low-frequency and high-frequency bands. This technique of signal pre-processing provides minimum distortion of the data, and results in a more optimal estimation of time constants of plant sensors using time-series modeling techniques.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Potential Application of Electrical Signature Analysis Methods for Monitoring Small Modular Reactor Components

This paper will describe the technical basis behind ESA and why we consider it a viable SMR condition monitoring technology. Concepts are presented of how ESA could be applied to monitor two candidate small modular reactor components: the main coolant pumps and the control rod drives. We believe the general health of these two components can be monitored and trended over time, using ESA methods. Our optimism is based on over two decades of ESA development and testing on a wide variety of components and systems, many of which have similar operational features to the main coolant pumps and control rod drives.

Damiano, Brian↗