Engineering Papers⌕ Search

Engineering topics

Dai, Sheng

Publications and source records attributed to Dai, Sheng.

At least 109 records · Page 6

Conformal LiF Stabilized Interfaces via Electrochemical Fluorination on High Voltage Spinel Cathodes (≈4.9 V) for Lithium-Ion Batteries

The high voltage LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel is one of the promising cathodes for the lithium-ion batteries due to its high energy densities, good rate performance. However, its high operating potential (≈4.75 V) causes extensive oxidation of conventional carbonate electrolytes, resulting an unstable and thick cathode electrolyte interphase (CEI) layer with a large irreversible capacity and low coulombic efficiency. In this work, we report the formation of thin LiF stabilized interfaces on LNMO via electrochemical fluorination that significantly improves the cycling stability and enhanced the capacity. An electrochemically induced conformal LiF layer acts as a part of a robust CEI by reducing the leakage of electrons and allowing the conduction of Li ions through it. Because of the robust LiF stabilized CEI, LNMO delivers a discharge capacity of ≈148.5 and ≈117.1 mAh g -1 at 0.1 and 1 C rate, respectively. It exhibits excellent cyclability with 80% capacity retention (CR) after 600 cycles in lithium-half cell and ≈90% CR after 200 cycles in full cell with only 0.03% and 0.05% capacity decay per cycle in conventional carbonate electrolytes without additives. Such an excellent electrochemical performance could lead to the potential development of high energy density batteries with high voltage cathodes for grid-based applications.

25 ENERGY STORAGE↗

In-situ synthesis of porous metal fluoride@carbon composite via simultaneous etching/fluorination enabled superior Li storage performance

Transition metal fluorides as Li-free conversion-type cathode materials have high theoretical specific capacities, however, their preparation strategy, sluggish electrochemical kinetic and poor cyclability have impeded their wide adoption in lithium-ion batteries. Herein, a facile in-situ synthesis of porous metal-fluoride-carbon composites is accomplished via simultaneous polytetrafluorethylene-based hard template etching and metal fluorination. This not only facilitates fast electron transfer and lithium-ion diffusion kinetics, but also buffers severe volume fluctuation during lithiation/delithation and enables the formation of a uniform and thin Li 2 CO 3 /LiF-rich cathode-electrolyte interphase. Here, as a proof of concept, the as-prepared porous FeF 3 @C (p-FeF 3 @C) indeed exhibits a high specific capacity of 230 mAh g -1 at 0.1 C together with an excellent capacity retention of 92.5% at 1 C for 200-cycles. Moreover, the practicality of the strategy is demonstrated by the superb electrochemical performance of the full-cells coupled with pre-lithiated graphite anodes. Therefore, the proposed novel synthetic strategy will enlighten the future design of high-performance metal-fluoride-carbon composites with porous structure for energy storage applications.

25 ENERGY STORAGE↗

Prospective Life Cycle Assessment of Synthetic Graphite Manufactured via Electrochemical Graphitization

Lithium-ion batteries (LIBs) are expected to play a crucial role in meeting many of the clean energy-related goals. Due to its electrical properties such as good conductance, chemical inertness, and corrosion resistance, graphite is a very popular anode for LIBs. Traditional methods of producing battery-grade graphite (high purity >99%) include processing naturally mined graphite or manufacturing synthetic graphite via the Acheson process, which converts soft amorphous carbons such as petroleum coke into graphite by subjecting it to high temperature (up to 3000 °C) for prolonged periods of times (3–5 days). However, due to a lack of abundant high purity natural graphite sources, synthetic graphite is the preferred choice for many LIBs. A new synthetic electrochemical graphitization method that subjects the amorphous carbon precursor submerged in a molten salt mixture to a constant cathodic polarization (against a graphitic anode) has been discovered that has significantly lower graphitization temperatures (~800 °C) and reduced graphitization time (3–6 h). Furthermore, the method can accept a higher variety of carbon precursors compared to the Acheson process. A prospective life cycle assessment (LCA) is conducted on this new method and compared against the traditional processes. The laboratory-scale demonstration of the method is used to build an inventory, which through various assumptions is scaled up to a commercial scale. An additional scenario is also considered with a biomass-derived carbon precursor for the graphite. The results from the LCA show that while the laboratory scale process is similar to the Acheson process and natural flake graphite in terms of impact, the scaled-up process is drastically better than the Acheson process in all environmental categories. Using a coconut shell-derived biomass precursor has a higher impact due to its manufacturing in Indonesia, as the Indonesian energy grid is highly fossil fuel dependent. Therefore, the biomass carbon may have a higher impact than petroleum coke dependent on the location of production of biomass-derived carbon black. The LCA has identified the molten salt—CaCl 2 —as a potential hotspot and suggests other salts should be considered. Accordingly, the new method shows promise in this early stage LCA in improving the environmental performance of graphite (and by relation LIBs) and therefore needs to be explored more in terms of its commercial viability.

25 ENERGY STORAGE↗

Strategies for design and synthesis of porous liquids toward carbon capture and separation

Porous liquids (PLs) represent a promising category of sorbents in carbon capture and separation capable of integrating the advantages of flowing liquid and porous solid systems. Well-defined pores were engineered into liquid sorbents via liquifying molecules with stiff interior voids, dissolving rigid porous hosts in flowing liquids, or dispersing porous frameworks in high steric hindrance solvents, producing type I, II, or III PLs, respectively. Unique features of PLs have triggered broad interest in exploring their applications in carbon capture and separation, in which diverse design strategies, synthesis approaches, and enhanced performance have been reported. Here, in this minireview, recent progress in the design, synthesis, and structural engineering of PLs and efforts towards the optimization of their carbon capture and separation behavior will be summarized, including the comparison between PLs with varied types. Porosity engineering into liquid sorbents provides opportunities to resolve challenging issues in conventional sorption and separation systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Construction of Fluorine- and Piperazine-Engineered Covalent Triazine Frameworks Towards Enhanced Dual-Ion Positive Electrode Performance

Organic positive electrodes featuring lightweight, and tunable energy storage modes by molecular structure engineering have promising application prospects in dual-ion batteries. Herein, a series of highly porous covalent triazine frameworks (CTFs) were synthesized under ionothermal conditions using fluorinated aromatic nitrile monomers containing a piperazine ring. Fluorinated monomers can result in more defects in CTFs, leading to a higher surface area up to 2515 m 2 /g and a higher N content of 11.34 wt% compared to the products from the non-fluorinated monomer. The high surface area and abundant redox sites of these CTFs afforded high specific capacities (up to 279 mAh/g at 0.1 A/g), excellent rate performance (89 mAh/g at 5 A/g), and durable cycling performance (92.3% retention rate after 500 cycles at 2.0 A g -1 ) as dual-ion positive electrodes

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computational Insights into Malononitrile-Based Carbanions for CO 2 Capture

Although anionic N and O sites have been widely used in chemisorption of CO 2 , carbanions are much less explored for CO 2 capture. Here, in this study, we employ ab initio calculations and quantum mechanical/molecular mechanical (QM/MM) molecular dynamics (MD) simulations to examine the interaction between CO 2 and the malononitrile carbanion, [CH(CN) 2 ] – . We have explored the potential energy surface of CO 2 binding by scanning the C–C distance between CO 2 and the central C site of the carbanion. We find that CO 2 prefers to bind to the nitrile group physically rather than to form a C–C bond via the carboxylation reaction at the sp 2 C site. Moreover, the two –CN groups can attract two CO 2 molecules at equal strength. The presence of an alkali metal ion enhances both physical and chemical interactions of CO 2 with the malononitrile carbanion. QM/MM MD simulations further confirm the preference of physical interaction in the condensed ionic liquid phase with a phosphonium cation. Our findings suggest that ionic liquids based on the malononitrile carbanion may have a high CO 2 solubility for carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemical noise studies on localized corrosion of Ni and Ni-20Cr in molten ZnCl 2

The electrochemical noise (ECN) technique was employed to study corrosion of two model systems, i.e. pure Ni and a binary Ni-20 wt%Cr (Ni20Cr) alloy in molten ZnCl 2 at 623 K. Here we measured ECN transients in current and open-circuit potential from two nominally identical Ni-Ni and Ni20Cr-Ni20Cr electrodes and one galvanic Ni-Ni20Cr electrode pair. The behavior of ECN is quite distinct among the three-electrode systems, and it is correlated with the various microscopic observations of micro- and nano-scale morphological features. Based on the ECN study coupled with the microstructural analysis, the origins of ECN in the molten salt environment as well as the mechanisms of localized corrosion in the three systems are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lignin-Derived Magnetic Activated Carbons for Effective Methylene Blue Removal

Large-scale environmental remediation of polluted water requires an effective and recyclable adsorbent produced from an abundant, low-cost, and renewable feedstock via a simple processing procedure. In this work, we demonstrate that lignin-derived magnetic activated carbons (mACs) uniquely satisfy these five criteria for (i) high-performance adsorption, (ii) high regeneration efficiency, (iii) feedstock economic and environmental viability, (iv) single-step processing and (v) large-scale production. The mACs are synthesized via an efficient co-carbonization and activation with simultaneous impregnation of ferric sulfate. Here, the Langmuir model closely fits the adsorption of methylene blue (MB) by mACs within the temperature range of 298–323 K, where the adsorption capacity increases as temperature increases. This capacity increased from 55.0 mg g -1 to 220.2 mg g -1 with the presence of magnetic nanoparticles. In addition, the magnetite nanoparticles on the ACs surface significantly improve its recycling ability with the removal percentage above 95% after four cycles for 5:1 mAC.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Batteries (2021 Annual Progress Report)

This document summarizes the progress of VTO battery R&D projects supported during the fiscal year 2021 (FY 2021). In FY 2021, the DOE VTO battery R&D funding was approximately $\$$115 million. Its R&D focus was on the development of high-energy batteries for EVs as well as very high-power devices for hybrid vehicles. The electrochemical energy storage roadmap (which can be found at the EERE Roadmap web page2) describes ongoing and planned efforts to develop electrochemical storage technologies for EVs. To advance battery technology, which can in turn improve market penetration of PEVs, the program investigates various battery chemistries to overcome specific technical barriers, e.g., battery cost, performance, life (both the calendar life and the cycle life), its tolerance to abusive conditions, and its recyclability/sustainability. VTO R&D has had considerable success, lowering the cost of EV battery packs to $\$$185/kWh in 2019 (representing more than 80% reduction since 2008) yet even further cost reduction is necessary for EVs to achieve head-to-head cost competitiveness with ICEs (without Federal subsidies). In addition, today’s batteries also need improvements in such areas as their ability to accept charging at a high rate, referred to as extreme fast charging (XFC) (15 minute charge) – to provide a “refueling” convenience similar to ICEs, and the ability to operate adequately at low temperatures. Research into “next-gen lithium-ion” batteries which would provide such functionalities is one of the R&D focus areas. VTO is funding research on both “next gen” chemistries (which employ an alloy anode and/or a high voltage cathode) and beyond lithium-ion (BLI) chemistries (which can, for example, employ a lithium metal anode).

25 ENERGY STORAGE↗

Creating Frustrated Lewis Pairs in Defective Boron Carbon Nitride for Electrocatalytic Nitrogen Reduction to Ammonia

Abstract The electrocatalytic nitrogen reduction reaction (NRR) on metal‐free catalysts is an attractive alternative to the industrial Haber–Bosch process. However, the state‐of‐the‐art metal‐free electrocatalysts still suffer from low Faraday efficiencies and low ammonia yields. Herein, we present a molecular design strategy to develop a defective boron carbon nitride (BCN) catalyst with the abundant unsaturated B and N atoms as Lewis acid and base sites, which upgrades the catalyst from a single “Lewis acid catalysis” to “frustrated Lewis pairs (FLPs) catalysis.” 14 N 2 / 15 N 2 exchange experiments and density functional theory (DFT) calculations reveal that FLPs can adsorb an N 2 molecule to form a six‐membered ring intermediate, which enables the cleavage of N 2 via a pull–pull effect, thereby significantly reducing the energy barrier to −0.28 eV. Impressively, BCN achieves a high Faraday efficiency of 18.9 %, an ammonia yield of 20.9 μg h −1 mg −1 cat. , and long‐term durability.

Lin, Wenwen↗

Creating Frustrated Lewis Pairs in Defective Boron Carbon Nitride for Electrocatalytic Nitrogen Reduction to Ammonia

Abstract The electrocatalytic nitrogen reduction reaction (NRR) on metal‐free catalysts is an attractive alternative to the industrial Haber–Bosch process. However, the state‐of‐the‐art metal‐free electrocatalysts still suffer from low Faraday efficiencies and low ammonia yields. Herein, we present a molecular design strategy to develop a defective boron carbon nitride (BCN) catalyst with the abundant unsaturated B and N atoms as Lewis acid and base sites, which upgrades the catalyst from a single “Lewis acid catalysis” to “frustrated Lewis pairs (FLPs) catalysis.” 14 N 2 / 15 N 2 exchange experiments and density functional theory (DFT) calculations reveal that FLPs can adsorb an N 2 molecule to form a six‐membered ring intermediate, which enables the cleavage of N 2 via a pull–pull effect, thereby significantly reducing the energy barrier to −0.28 eV. Impressively, BCN achieves a high Faraday efficiency of 18.9 %, an ammonia yield of 20.9 μg h −1 mg −1 cat. , and long‐term durability.

Lin, Wenwen↗

Insight into the Fast-Rechargeability of a Novel Mo 1.5 W 1.5 Nb 14 O 44 Anode Material for High-Performance Lithium-Ion Batteries

Wadsley–Roth phased niobates are promising anode materials for lithium-ion batteries, while their inherently low electrical conductivity still limits their rate-capability. Herein, a novel doped Mo 1.5 W 1.5 Nb 14 O 44 (MWNO) material is facilely prepared via an ionothermal-synthesis-assisted doping strategy. The detailed crystal structure of MWNO is characterized by neutron powder diffraction and aberration corrected scanning transmission electron microscope, unveiling the full occupation of Mo 6+ -dopant at the t1 tetrahedral site. In half-cells, MWNO exhibits enhanced fast-rechargeability. In this work, the origin of the improved performance is investigated by ultraviolet–visible diffuse reflectance spectroscopy, density functional theory (DFT) computation, and electrochemical impedance spectroscopy, revealing that bandgap narrowing improves the electrical conductivity of MWNO. Furthermore, operando X-ray diffraction elucidates that MWNO exhibits a typical solid-solution phase conversion-based lithium-ion insertion/extraction mechanism with reversible structural evolution during the electrochemical reaction. The boosted lithium-ion diffusivity of MWNO, due to the Mo 6+ /W 6+ doping effect, is confirmed by a galvanostatic intermittent titration technique and DFT. With the simultaneously enhanced electrical conductivity and lithium-ion diffusivity, MWNO successfully demonstrates its fast-rechargeability and practicality in the LiNi 0.5 Mn 1.5 O 4 -coupled full-cells. Therefore, this work illustrates the potential of ionothermal synthesis in energy storage materials and provides a mechanistic understanding of the doping effect on improving material's electrochemical performance.

25 ENERGY STORAGE↗

Fully Conjugated Poly(phthalocyanine) Scaffolds Derived from a Mechanochemical Approach Towards Enhanced Energy Storage

Phthalocyanines (Pc)-derived materials represent an attractive category of porous organic scaffolds featured by extensive π-conjugated networks, but their construction is still limited to the solution-based pathways, producing materials with inferior conductivity and porosity. Herein, a mechanochemistry-driven approach was developed leveraging the on-surface polymerization of aromatic nitrile monomers with ortho-positioned dicyano groups in the presence of metal catalysts (magnesium, zinc, or aluminum) under neat and ambient conditions. Diverse Pc-functionalized conjugated porous networks (Pc-CPNs) were obtained featured by extensively and fully π-conjugated skeletons, high surface areas, and hierarchical porosities. The monomers in this mechanochemical approach could be extended to those difficult to be handled in solution-based procedures. In this work, the Pc-CPNs displayed attractive electrochemical performance as supercapacitor and anodes in batteries, together with superb long-term stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced Oxygen Activation Achieved by Robust Single Chromium Atom-Derived Catalysts in Aerobic Oxidative Desulfurization

Oxidative desulfurization (ODS) plays critical roles in the production of high-quality sulfur impurity-free fuels, especially procedures using molecular oxygen as the sole oxidant. However, the state-of-the-art systems still rely on noble metal nanocatalysts, with deactivation issues caused by coking and sintering still present. In this work, leveraging the merits of single-atom catalysts (SACs) with earth-abundant metal cores and robust nanoporous supports, a series of catalysts composed of homogeneously distributed single chromium atoms anchored on multiwalled carbon nanotubes were fabricated and deployed to catalyze the aerobic ODS transformation. Adopting aromatic sulfur compound (ASC)-containing alkanes as a model system with molecular oxygen as the oxidant, efficient oxygen-to-active O 2 •– transformation and subsequent ASCs-to-sulfone conversion have been achieved, with the former benefiting from the chromium-active sites and the latter arising from the robust, nanoporous, and π-conjugated architecture of the supports. The attractive catalytic performance and cycling stability of the chromium-based SACs make them promising candidates in practical sulfur species removal from liquid fuels, supplying an alternative guidance on the catalyst design toward cost-effective and energy-efficient ODS procedures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Research on high power, doped titanium-niobium oxide anodes

The main objective of this project is to synthesize titanium niobium oxide (TNO) that has a nanoporous structure with porous channels for rapid lithium diffusion, enabling extreme fast charging (XFC). The focus of this project is to improve the electronic conductivity and ion diffusion coefficient in TNO to achieve high capacities under extreme fast charge conditions. In addition, electrolytes with additives will be formulated to promote stable interphase formation on the NMC cathode surface to improve long cycling stability.

25 ENERGY STORAGE↗

On the Fidelity of Computational Models for the Flow of Milled Loblolly Pine: A Benchmark Study on Continuum-Mechanics Models and Discrete-Particle Models

The upstream of bioenergy industry has suffered from unreliable operations of granular biomass feedstocks in handling equipment. Computational modeling, including continuum-mechanics models and discrete-particle models, offers insightful understandings and predictive capabilities on the flow of milled biomass and can assist equipment design and optimization. This paper presents a benchmark study on the fidelity of the continuum and discrete modeling approaches for predicting granular biomass flow. We first introduce the constitutive law of the continuum-mechanics model and the contact law of the coarse-grained discrete-particle model, with model parameters calibrated against laboratory characterization tests of the milled loblolly pine. Three classical granular material flow systems (i.e., a lab-scale rotating drum, a pilot-scale hopper, and a full-scale inclined plane) are then simulated using the two models with the same initial and boundary conditions as the physical experiments. The close agreement of the numerical predictions with the experimental measurements on the hopper mass flow rate, the hopper critical outlet width, the material stopping thickness on the inclined plane, and the dynamic angle of repose, clearly indicates that the two methods can capture the critical flow behavior of granular biomass. The qualitative comparison shows that the continuum-mechanics model outperforms in parameterization of materials and wall friction, and large-scale systems, while the discrete-particle model is more preferred for discontinuous flow systems at smaller scales. Industry stakeholders can use these findings as guidance for choosing appropriate numerical tools to model biomass material flow in part of the optimization of material handling equipment in biorefineries.

Jin, Wencheng↗

Mechanochemistry-driven phase transformation of crystalline covalent triazine frameworks assisted by alkaline molten salts

We report covalent triazine frameworks (CTFs) have shown wide applications in the fields of separation, catalysis, energy storage, and beyond. However, it is a long-term challenging subject to fabricate high-quality CTF materials via facile procedures. Herein, a mechanochemistry-driven procedure was developed to achieve phase transformation of crystalline CTFs assisted by alkaline molten salts. The transformation of CTF-1 from staggered AB to eclipsed AA stacking mode was achieved by short time (30 min) mechanochemical treatment in the presence of molten salts composed of LiOH/KOH, generating high-quality CTF-1 material with high crystallinity, high surface area (625 m 2 g -1 ), and permanent/ordered porosity without carbonization under ambient conditions. This facile procedure could be extended to provide nanoporous three-dimensional CTF materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Real-Space Local Dynamics of Molten Inorganic Salts Using Van Hove Correlation Function

Molten inorganic salts are attracting resurgent attention because of their unique physicochemical properties, making them promising media for next-generation concentrating solar power systems and molten salt reactors. The dynamics of these highly disordered ionic media is largely studied by theoretical simulations, while the robust experimental techniques capable of observing local dynamics are not well-developed. To provide fundamental insights into the atomic-scale transport properties of molten salts, we report the real-space dynamics of molten magnesium chloride at high temperatures employing the Van Hove correlation function obtained by inelastic neutron scattering. Overall, our results directly depict the distance-dependent dynamics of a molten salt on the picosecond time scale. This study demonstrates the capability of the developed approach to describe the locally correlated- and self-dynamics in molten salts, significantly improving our understanding of the interplay between microscopic structural parameters and their dynamics that ultimately control physical properties of condensed matter in extreme environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗