Engineering Papers⌕ Search

Engineering topics

Curreri, Peter A.

Publications and source records attributed to Curreri, Peter A..

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Steady State Sedimentation in a Liquid Fluidized Bed

The velocity fluctuations and the local particle concentration of a particle suspension exhibiting steady state sedimentation in a fluidized bed are determined as a function of height along the particle column. Both the velocity fluctuations and the particle volume fraction are found to strongly depend on height. We account for the stability of the bed by a simple model evoking a flux balance. Velocity fluctuations driving a downward particle flux are compensated by an upward particle flux stemming from an excess flow velocity due to the concentration gradient of the system.

Segre, P. N.↗
NASA NTRS2002

The Effect of the Wall Contact and Post-Growth Cool-Down on Defects in CdTe Crystals Grown by 'Contactless' Physical Vapour Transport

A series of cadmium telluride crystals grown by physical vapor transport without contact with the ampoule walls and cooled at different rates were characterized using synchrotron X-ray topography, photoluminescence, and chemical etching. Strain from sticking to silica glass and its effect on the dislocation density is shown. It was found that very fast cool-down increases dislocation density by at least one order of magnitude. None of the samples had random dislocation distributions but coarse clumping of dislocations on the scale of more than 100 microns was more prevalent in slowly cooled crystals. Photoluminescence revealed that slow cooling favored the donor-acceptor luminescence involving complex A centers. This was diminished in fast cooled material; and effect presumed to be due to dislocation gettering. Fast cooling also enhanced the formation of shallow acceptors. Implications for Bridgman growth of CdTe and the vapor growth of CdZnTe are discussed briefly.

Palosz, W.↗
NASA NTRS2002

Surface Oscillations of An Electromagnetically Levitated Droplet

Oscillating droplets are of interest in a number of disciplines. A practical application is the oscillating drop method, which is a technique for measuring surface tension and viscosity of liquid metals. It is especially suited to undercooled and highly reactive metals, because it is usually performed by electromagnetic levitation. The natural oscillation frequency a f the droplets is related to the surface tension of the material, and the decay of oscillations is related to its viscosity. The fluid flow inside the droplet must be laminar in order for this technique to yield good results. Because no experimental method has yet been developed to visualize flow in electromagnetically-levitated oscillating metal droplets, mathematical modeling is required to determine whether or not turbulence occurs. Three mathematical models of the flow: (1) assuming laminar conditions, (2) using the turbulence model, and (3) using the RNG turbulence model, respectively, are compared and contrasted to determine the physical characteristics of the flow. It is concluded that the RNG model is the best suited for describing this problem. The goal of the presented work was to characterize internal flow in an oscillating droplet of liquid metal, and to verify the accuracy of the characterization by comparing calculated surface tension and viscosity values to experimentally-obtained results.

Berry, S.↗
NASA NTRS2002

Transient Torque Technique for Viscosity and Electrical Conductivity Determination of Semiconducting Liquids

A novel apparatus based on transient torque technique is constructed in MSFC/NASA. The apparatus uses a 125um diameter quartz fiber as torsion wire. A high sensitive angular detector is implemented to measure the deflection angle of the crucible containing the liquid. A rotating magnetic field (RMF) is used to induce a rotating flow of a conducting or semiconducting melts. By measuring the magnitude and transient behavior of the induced deflection angle, the electrical conductivity and viscosity of the melt can be measured simultaneously. High purity elements namely Hg, Ga, Zn and Te are tested at room temperature and high temperature up to 900 C.

Li, C.↗
NASA NTRS2002

Triggered Nucleation in Ni60Nb40 Using an Electrostatic Levitator

External triggering of nucleation in an undercooled liquid metal has been performed for the first time in an electrostatically levitated sample of undercooled eutectic Ni60Nb40. With the Electrostatic Levitator (ESL) facility at NASA/MSFC, NiNb alloys were externally nucleated at various undercooling increments. Observation of the resulting microstructure indicates that only one nucleation site is initiated with a trigger if the undercooling is sufficiently high. Well-defined transition zones exist in all the samples. An "anomalous" fine structured eutectic is initially grown from the nucleation point into the undercooled liquid followed by an unexpected variable width transition zone leading to a coarse structured region of dendrites. Our study tends to corroborate the findings of other studies on highly undercooled eutectics regarding a coupled growth zone within which the lamellar structure is formed and outside of which the anomalous is found.

Rathz, T.↗
NASA NTRS2002

Determination of the Absolute Number of Cytokine mRNA Molecules within Individual Activated Human T Cells

A primary function of activated T cells is the expression and subsequent secretion of cytokines, which orchestrate the differentiation of other lymphocytes, modulate antigen presenting cell activity, and alter vascular endothelium to mediate an immune response. Since many features of immune regulation probably result from modest alterations of endogenous rates of multiple interacting processes, quantitative analysis of the frequency and specific activity of individual T cells is critically important. Using a coordinated set of quantitative methods, the absolute number of molecules of several key cytokine mRNA species in individual T cells has been determined. The frequency of human blood T cells activated in vitro by mitogens and recall protein antigens was determined by intracellular cytokine protein staining, in situ hybridization for cytokine mRNA, and by limiting dilution analysis for cytokine mRNA+ cells. The absolute number of mRNA molecules was simultaneously determined in both homogenates of the entire population of cells and in individual cells obtained by limiting dilution, using a quantitative, competitive RT-PCR assay. The absolute numbers of mRNA molecules in a population of cells divided by the frequency of individual positive cells, yielded essentially the same number of mRNA molecules per cell as direct analysis of individual cells by limiting dilution analysis. Mean numbers of mRNA per positive cell from both mitogen and antigen activated T cells, using these stimulation conditions, were 6000 for IL-2, 6300 for IFN-gamma, and 1600 for IL-4.

Karr, Laurel J.↗
NASA NTRS2002

Studies of Nucleation and Growth, Specific Heat and Viscosity of Undercooled Melts of Quasicrystals and Polytetrahedral-Phase-Forming Alloys

The local atomic structures of undercooled liquid metals are presumed to be icosahedral; this order is incompatible with translational periodicity, constituting a barrier to the nucleation of the crystal phase. The extended atomic structure of the icosahedral quasicrystal (i-phase) is similar to that presumed in the undercooled liquid. Therefore, a comparison of the maximum undercooling in alloys that form the i-phase with those that form crystal phases provides a probe of the liquid structure.

Kelton, K. F.↗
NASA NTRS2002

Origin of the Large Bandgap Bowing in Highly Mismatched Semiconductor Alloys

We use a combination of optical and soft x-ray fluorescence techniques to investigate the composition dependence of the band edge energies in ZnSe(1-x)Te(x) and ZnS(1-x)Te(x) alloys. The results reveal entirely different origins of the large bandgap bowing for alloys with small and large Te content. On the Te-rich side, the reduction of the bandgap is well explained by the band anticrossing interaction between the Se or S localized states and the ZnTe conduction band states. On the Se or S-rich side, an interaction between the localized Te states and the degenerate GAMMA valence bands of ZnSe or ZnS is responsible for the bandgap reduction and the rapid increase of the spin-orbit splitting with increasing Te concentration. Results of soft x-ray fluorescence experiments provide direct evidence for the valence band anticrossing interaction. The bandgap bowing over the entire composition range is accounted for by a linear interpolation between the conduction band anticrossing and valence band anticrossing models.

Wu, J.↗
NASA NTRS2002

Carbon Nanotubes Growth on Graphite Fibers

Carbon nanotubes (CNT) were synthesized on graphite fibers by thermal Chemical Vapor Deposition (CVD). On the fiber surface, iron nanoparticles are coated and act as catalysts for CNT growth. The growth temperature ranges from 550 to 1000 C at an ambient pressure. Methane and hydrogen gases with methane contents of 10% to 100% are used for the CNT synthesis. At high growth temperatures (greater than 800 C), the rapid inter-diffusion of the transition metal iron on the graphite surface results in a rough fiber surface with no CNT grown on the surface. When the growth temperature is relatively low (650 - 800 C), CNT are fabricated on the graphite surface with catalytic particles on the nanotube top ends. Using micro Raman spectroscopy in the breath mode region, single-walled or multi-walled CNT can be determined, depending on methane concentrations.

Zhu, Shen↗
NASA NTRS2002

Analysis of Short and Long Range Atomic Order in Nanocrystalline Diamonds with Application of Powder Diffractometry

Fundamental limitations, with respect to nanocrystalline materials, of the traditional elaboration of powder diffraction data like the Rietveld method are discussed. A tentative method of the analysis of powder diffraction patterns of nanocrystals is introduced which is based on the examination of the variation of lattice parameters calculated from individual Bragg lines (named the "apparent lattice parameter", alp). We examine the application of our methodology using theoretical diffraction patterns computed for models of nanocrystals with a perfect crystal lattice and for grains with a two-phase, core-shell structure. We use the method for the analysis of X-ray and neutron experimental diffraction data of nanocrystalline diamond powders of 4, 6 and 12 nm in diameter. The effects of an internal pressure and strain at the grain surface is discussed. This is based on the dependence of the alp values oil the diffraction vector Q and on the PDF analysis. It is shown, that the experimental results support well the concept of the two-phase structure of nanocrystalline diamond.

Palosz, B.↗
NASA NTRS2002

Fabry-Perot Interferometer-Based Electrooptic Modulator using LiNbO3 and Organic Thin Films

We report the study of a Fabry-Perot electro-optical modulator using thin crystalline film NPP, and Crystalline LiNbO3. We are able to observe 14, and 60 percent degree of modulation. Measurements were carried using a standard lock-in amplifier with a silicon detector. The proposal to design a Fabry-Perot electro-optic modulator with an intracavity electro-optically active organic material was based on the initial results using poled polymer thin films. The main feature of the proposed device is the observation that in traditional electrooptic modulators like a Packets cell, it requires few kilovolts of driving voltage to cause a 3 dB modulation even in high figure-of-merit electrooptic materials like LiNbO3. The driving voltage for the modulator can be reduced to as low as 10 volts by introducing the electrooptic material inside die resonant cavity of a Fabry-Perot modulator. This is because the transmission of the Fabry-Perot cavity varies nonlinearly with the change of refractive index or phase of light due to applied electric field.

Banks, C.↗
NASA NTRS2002

Magnetic Microspheres for Therapeutical Applications

Hyperthermia is a well known cancer therapy and consists of heating a tumor region to the elevated temperatures in the range of 40-45 C for an extended period of time (2-8 hours). This leads to thermal inactivation of cell regulatory and growth processes with resulting widespread necrosis, carbonization and coagulation. Moreover, heat boosts the tumor response to other treatments such as radiation, chemotherapy or immunotherapy. Of particular importance is careful control of generated heat in the treated region and keeping it localized. Higher heating, to about 56 C can lead to tissue thermo-ablation. With accurate temperature control, hyperthermia has the advantage of having minimal side effects. Several heating techniques are utilized for this purpose, such as whole body hyperthermia, radio-frequency (RF) hyperthermia, ultrasound technique, inductive microwave antenna hyperthermia, inductive needles (thermoseeds), and magnetic fluid hyperthermia (MFH).MFH offers many advantages as targeting capability by applying magnets. However, this technology still suffers significant inefficiencies due to lack of thermal control. This paper will provide a review of the topic and outline the ongoing work in this area. The main emphasis is in devising ways to overcome the technical difficulty in hyperthermia therapy of achieving a uniform therapeutic temperature over the required region of the body and holding it steady. The basic obstacle of the present heating methods are non-uniform thermal properties of the tissue. Our approach is to develop a novel class of magnetic fluids which have inherent thermoregulating properties. We have identified a few magnetic alloys which can serve as a suitable nano-particle material. The objective is to synthesize, characterize and evaluate the efficacy of TRMF for hyperthermia therapy.

Mazuruk, K.↗
NASA NTRS2002

Laminar-Turbulent Transition in an Electromagnetically-Levitated Droplet

During experiments on the MSL-1 (First Microgravity Science Laboratory) mission of the Space Shuttle (STS-83 and STS-94, April and July 1997), a droplet of palladium-silicon alloy was electromagnetically levitated for viscosity measurements. For the non-deforming droplet, the resultant MHD flow inside the drop can be inferred from motion of impurity particulates on the surface. In the experiments, subsequent to melting, Joule heating produces a continuous reduction of viscosity of the fluid resulting in an acceleration of the flow with time. These observations indicate formation of a pair of corotating toroidal flow structures inside the spheroidal drop that undergo flow instabilities. As the fluid temperature rises, the amplitude of the secondary flow increases; and beyond a point, the tracers exhibit non-coherent chaotic motion signifying emergence of turbulence inside the drop. Assuming that the observed laminar-turbulent transition is shear-layer type, the internal structure of the toroidal loops is used to develop a semi-empirical correlation for the onset of turbulence. Our calculations indicate that the suggested correlation is in modest agreement with the experimental data, with the transition occurring at a Reynolds number of 600.

Hyers, Robert W.↗
NASA NTRS2002

Interaction of Porosity with a Planar Solid/Liquid Interface

In this paper, an investigation of the interaction between gas porosity and a planar solid/liquid (SL) interface is reported. A two-dimensional numerical model able to accurately track sharp SL interfaces during solidification of pure metals and alloys is proposed. The finite difference method and a rectangular undeformed grid are used for computation. The SL interface is described through the points of intersection with the grid lines. Its motion is determined by the thermal and solute gradients at each particular point. Changes of the interface temperature because of capillarity or solute redistribution as well as any perturbation of the thermal and solute field produced by the presence of non-metallic inclusions can be computed. To validate the model, the dynamics of the interaction between a gas pore and a solidification front in metal alloys was observed using a state of the art X-ray Transmission Microscope. The experiments included observation of the distortion of the SL interface near a pore, real-time measurements of the growth rate and the change in shape of the porosity during interaction with an advancing SL interface in pure Al and Al-0.25 wt% Au alloy. In addition, porosity induced solute segregation patterns surrounding a pore were also quantified.

Catalina, Adrian V.↗
NASA NTRS2002

Experimental Observations of Localization Phenomena in Sands: Plane Strain Versus Triaxial Compression Conditions

A comprehensive experimental investigation was conducted to investigate the effects of loading condition and confining pressure on strength properties and instability phenomena in sands. A uniform sub-rounded to rounded natural silica sand known as F-75 Ottawa sand was used in the investigation. The results of a series on Conventional Triaxial Compression (CTC) experiments tested under very low confining pressures (0.05 - 1.30) kPa tested in a Microgravity environment abroad the NASA Space Shuttle are presented in addition to the results similar specimens tested in terrestrial laboratory to investigate the effect of confining pressure on the constitutive behavior of sands. The behavior of the CTC experiments is compared with the results of Plane Strain (PS) experiments. Computed tomography and other digital imaging techniques were used to study the development and evolution of shear bands.

Alshibli, Khalid A.↗
NASA NTRS2002

A New Analytical Approach to Predict Spacing Selection in Lamellar and Rod Eutectic Systems

The Jackson and Hunt (JH) theory has been modified to relax the assumption of isothermal solid/liquid interface(SLI) used in their treatment. Based on the predictions of this modified theory the traditional definitions of regular and irregular eutectics are revised. For regular eutectics the new model identifies a range of spacing within the limits defined by the minimum undercooling of the alpha and beta phase. For the irregular Al-Si eutectic system two different spacing selection mechanisms were identified: a) for a particular growth rate, a nearly isothermal interface can be achieved at a unique minimum spacing lambda(sub I); b) the average spacing (lambda(sub av) greater than lambda(sub I)) is essentially dictated by the undercooling of the faceted phase. Based on the modified theoretical model a semiempirical expression has been developed to account for the influence of the temperature gradient, which is dominant in the irregular Al-Si system. The behavior of the Fe-Fe3C eutectic is also discussed The theoretical calculations have been found to be in good agreement with the published experimental measurements.

Catalina, Adrian V.↗
NASA NTRS2002

Toward Understanding Pore Formation And Mobility During Controlled Directional Solidification In A Microgravity Environment Investigation (PFMI)

The generation and inclusion of detrimental porosity, e.g., "pipes" and "rattails" can occur during controlled directional solidification processing. The origin of these defects is generally attributed to gas evolution and entrapment during solidification of the melt. On Earth, owing to buoyancy, an initiated bubble can rapidly rise through the liquid melt and "pop" at the surface; this is obviously not ensured in a low gravity or microgravity environment. Clearly, porosity generation and inclusion is detrimental to conducting any meaningful solidification-science studies in microgravity. Thus it is essential that model experiments be conducted in microgravity, to understand the details of the generation and mobility of porosity, so that methods can be found to eliminate it. In hindsight, this is particularly relevant given the results of the previous directional solidification experiments conducted in Space. The current International Space Station (ISS) Microgravity Science Glovebox (MSG) investigation addresses the central issue of porosity formation and mobility during controlled directional solidification processing in microgravity. The study will be done using a transparent metal-analogue material, succinonitrile (SCN) and succinonitrile-water "alloys", so that direct observation and recording of pore generation and mobility can be made during the experiments. Succinonitrile is particularly well suited for the proposed investigation because it is transparent, it solidifies in a manner analogous to most metals, it has a convenient melting point, its material properties are well characterized and, it has been successfully used in previous microgravity experiments. The PFMI experiment will be launched on the UF-2, STS-111 flight. Highlighting the porosity development problem in metal alloys during microgravity processing, the poster will describe: (i) the intent of the proposed experiments, (ii) the theoretical rationale behind using SCN as the study material for porosity generation and migration and, (iii) the experimental protocol for the investigation of the effects of the processing parameters. Photographs of the flight experimental hardware, and the novel sample ampoule, will be exhibited. The experimental apparatus will be described in detail and a summary of the scientific objectives will be presented.

Grugel, R. N.↗