Engineering topics

Curreri, P. A.

Publications and source records attributed to Curreri, P. A..

59 records · Page 4

NASA NTRS1984

Containerless drop tube solidification and grain refinement of NiAl3

The possibility of undercooling Ni-Al alloys below the liquidus in order to produce a single phase peritectic structure by containerless drop tube solidification was studied. Containerless process is a technique for both high purity contamination free studies as well as for investigating the undercooling and rapid solidification of alloys by suppression of heterogeneous nucleation on container walls. In order to achieve large undercoolings one must avoid heterogeneous nucleation of crystallization. It was shown that the Marshall Space Flight Center drop tubes ae unique facilities for containerless solidification experiments and large undercoolings are possible with some alloys. The original goal of undercooling the liquid metal well below the liquidus to the peritectic temperature during containerless free to form primarily NiAl3 was achieved. The microstructures were interesting from another point of view. The microstructure from small diameter samples is greatly refined. Small dendrite arm spacings such as these could greatly facilitate the annealing and solid state transformation of the alloy to nearly 10% NiAl3 by reducing the distance over which diffusion needs to occur. This could minimize annealing time and might make it economically feasible to produce NiAl3 alloy.

Ethridge, E. C.↗

NASA NTRS1984

Design and implementation of a low-gravity solidification experiment package for the F-104

The use of the F-104 Interceptor for low gravity materials processing experiments is extended to include alloy solidification studies above 1000 C. The F-104 can provide up to 60 seconds of low gravity, but requires a unique experiment package for integration into the aircraft, both physically and electronically. The current research with the F-104 experimental furnace system which has been used to process cast iron samples is described. Results demonstrate the capability of the facility and its operation.

Smith, G.↗

NASA NTRS1983

Electromagnetic levitation coil fabrication technique for MSFC containerless processing facilities

A technique is described for more reproducible fabrication of electromagnetic levitation coils. A split mandrel was developed upon which the coil is wound. After fabrication the mandrel can be disassembled to remove it from the coil. Previously, a full day was required to fabricate a levitation coil and the success rate for a functional coil was only 50 percent. About eight coils may be completed in one day using the technique developed and 95 percent of them are good levitation coils.

Ethridge, E. C.↗

NASA NTRS1983

Preliminary science report on the directional solidification of hypereutectic cast iron during KC-135 low-G maneuvers

An ADSS-P directional solidification furnace was reconfigured for operation on the KC-135 low-g aircraft. The system offers many advantages over quench ingot methods for study of the effects of sedimentation and convection on alloy formation. The directional sodification furnace system was first flown during the September 1982 series of flights. The microstructure of the hypereutectic cast iron sample solidified on one of these flights suggests a low-g effect on graphite morphology. Further experiments are needed to ascertain that this effect is due to low-gravity and to deduce which of the possible mechanisms is responsible for it.

Curreri, P. A.↗

NASA NTRS1983

The feasibility of low-G grey solidification of nodular iron in the F-104 experimental furnace package

The rationale for low-g experiments with cast iron and the need for solidification in the grey form during these experiments are reviewed. The factors which determine whether an iron melt will solidify grey or white are discussed. Cooling rate versus microstructure was studied for a nodular iron candidate material for F-104 low-g solidification. The study determined that low-g grey solidification, using the present F-104 furnace system, of the nodular iron composition studied is not feasible. Specimen microstructure strongly suggested that the F-104 furnace's gas cooling system was causing excessive localized chill resulting in the nucleation of the unwanted iron carbide phase. A change is suggested, in the quench system design, that could possibly overcome this problem.

Curreri, P. A.↗