Engineering topics

Cullen, David A.

Publications and source records attributed to Cullen, David A..

86 records · Page 5

DOE OSTI2022

MoS 2 nanosheet integrated electrodes with engineered 1T-2H phases and defects for efficient hydrogen production in practical PEM electrolysis

Low electrical conductivity and poor accessibility of MoS 2 reaction sites raise great challenges in maximizing the triple-phase-boundary (TPB) sites of MoS 2 -based electrodes and minimizing ohmic losses for efficient hydrogen evolution reaction (HER) in practical proton exchange membrane (PEM) water electrolysis. Herein, we report a scalable hydrothermal approach to fabricate ionomer-free integrated electrodes with engineered 1 T-2 H heterophase and defect-rich MoS 2 nanosheets (MoS 2 NSs) in-situ grown onto the carbon fiber paper (CFP). With an ultralow loading of 0.14 mg/cm 2 , a small voltage of 2.25 V was obtained at 2000 mA/cm 2 in a practical cell with Nafion115 membrane, which outperforms all previously reported high-loading non-precious catalyst-based electrodes. Impressively, it shows 44 times higher mass activity than a high-loading and ionomer-mixed MoS 2 assemblies electrode. Furthermore, this work builds a bridge from catalyst optimization to electrode fabrication and provides a promising direction for improving intrinsic catalytic activity, electrode conductivity and stability for practical PEM water electrolysis.

1T-2H heterophase↗

DOE OSTI2022

Design of PGM-free cathodic catalyst layers for advanced PEM fuel cells

Here, the design of cathodic catalysts layer (CCL) consisted of Platinum Group Metal-free (PGM-free) electrocatalysts was done by catalyst coated membrane approach. Three different Fe-Mn-N-C compounds were synthesized with Fe:Mn ratio of 1:1, 2:1 and 2:1 with modified heat treatment profile. The catalysts were characterized by X-ray photoelectron spectroscopy, X-ray powder diffraction, pore and particle size distribution, zeta potential and transmission electron microscopy. Electrocatalysts were integrated into membrane electrode assembly and evaluated by electrochemical methods. Electrochemical impedance spectroscopy in combination with modeling were used for estimation of proton conductivity of CCL and its oxygen diffusivity. It was found that all CCLs possess extremely high proton conductivity, which was demonstrated for the first time for these types of PGM-free catalysts. The observed ORR mechanism was predominantly 4e- due to peroxide/radicals scavenging effect of Mn.

impedance↗

DOE OSTI2022

Chemical preintercalation synthesis approach for the formation of new layered tungsten oxides

Tungsten oxide, WO 3 ·nH 2 O, is a unique layered oxide material that offers enhanced performance in electrochromic and energy storage applications. Herein, we report the formation of a new, never previously synthesized, Na-containing layered tungsten oxide phase, Na 0.20 WO 3 ·0.81H 2 O, using a chemical preintercalation approach. The structure and composition of this novel phase were investigated via microscopy, spectroscopy, and diffraction methods. Electrochemical cycling of Na 0.20 WO 3 ·0.81H 2 O electrodes revealed initial discharge capacities of 37.43 mAh g -1 , 480.8 mAh g -1 , and 253.2 mAh g -1 in aqueous H 2 SO 4 cells (potential window of - 0.2–0.8 V vs. Ag/AgCl), non-aqueous Li-ion cells (potential window of 0.1–4.0 V vs. Li/Li + ), and non-aqueous Na-ion cells (potential window of 0.1–4.0 V vs. Na/Na + ), respectively. Additionally, a reversible, pressure-induced color change from pale yellow to dark brown/black was observed for the Na 0.20 WO 3 ·0.81H 2 O sample when it was placed under pressures of 1000 psi or higher. Our results demonstrate the viability of chemical preintercalation synthesis approach to produce new oxide phases with interesting functional properties.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Coupled continuum and network model framework to study catalyst layers of polymer electrolyte fuel cells

The nanostructured thin film (NSTF) catalyst layers which have demonstrated high power densities, mass activities, and exceptional metal and support stability can have limited operational robustness due to their thin thickness and the hydrophilicity of the metal-coated nano whiskers. The dispersed nanostructured thin film (dNSTF) catalyst layers have been developed by dispersing the NSTF Pt whiskers with ionomer and carbon support to increase the thickness and hydrophobicity. Continuum and network models (NM) are coupled through boundary conditions to study the polymer electrolyte fuel cell with a dNSTF cathode catalyst layer. The coupled model combines the computational efficiency of the continuum model with the pore-scale information in the dNSTF cathode catalyst layer of the NM. It captures the special morphology of the partially ionomer/water covered cylindrical whiskers, as well as water percolation through the pore structures and their impact on the cell performance. Here we observe optimal ionomer coverage on whiskers to be 0.5, ionomer to carbon ratio to be 0.9 and higher whisker to carbon ratios to be desired.

08 HYDROGEN↗

DOE OSTI2022

Recovering carbon losses in CO 2 electrolysis using a solid electrolyte reactor

The practical implementation of electrochemical CO 2 reduction technology is greatly challenged by notable CO 2 crossover to the anode side, where the crossed-over CO 2 is mixed with O 2 , via interfacial carbonate formation in traditional CO 2 electrolysers. Here we report a porous solid electrolyte reactor strategy to efficiently recover these carbon losses. Furthermore, by creating a permeable and ion-conducting sulfonated polymer electrolyte between cathode and anode as a buffer layer, the crossover carbonate can combine with protons generated from the anode to re-form CO 2 gas for reuse without mixing with anodic O 2 . Using a silver nanowire catalyst for CO 2 reduction to CO, we demonstrated up to 90% recovery of the crossover CO 2 in an ultrahigh gas purity form (>99%), while delivering over 90% CO Faradaic efficiency under a 200 mA cm -2 current. A high continuous CO 2 conversion efficiency of over 90% was achieved by recycling the recovered CO 2 to the CO 2 input stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Recreating Fuel Cell Catalyst Degradation in Aqueous Environments for Identical-Location Scanning Transmission Electron Microscopy Studies

The recent surge in interest of proton exchange membrane fuel cells (PEMFCs) for heavy-duty vehicles increases the demand on the durability of oxygen reduction reaction electrocatalysts used in the fuel cell cathode. This prioritizes efforts aimed at understanding and subsequently controlling catalyst degradation. Identical-location scanning transmission electron microscopy (IL-STEM) is a powerful method that enables precise characterization of degradation processes in individual catalyst nanoparticles across various stages of cycling. Recreating the degradation processes that occur in PEMFC membrane electrode assemblies (MEAs) within the aqueous cell used for IL-STEM experiments is vital for generating an accurate understanding of these processes. In this work, we investigate the type and degree of catalyst degradation achieved by cycling in an aqueous cell compared to a PEMFC MEA. While significant degradation is observed in IL-STEM experiments performed on a traditional Pt catalyst using the standard accelerated stress test potential window (0.6-0.95 VRHE), degradation of a PtCo catalyst designed for heavy-duty vehicle use is very limited compared to that observed in MEAs. We therefore explore various experimental parameters such as temperature, acid type, acid concentration, ionomer content, and potential window to identify conditions that reproduce the degradation observed in MEAs. We find that by extending the cycling potential window to 0.4-1.0 V RHE in an electrolyte containing Pt ions, the degraded particle size distribution and alloy composition better match that observed in MEAs. In particular, these conditions increase the relative contribution of Ostwald ripening, which appears to play a more significant role in the degradation of larger alloy particles supported on high-surface-area carbons than coalescence. Results from this work highlight the potential for discrepancies between ex situ aqueous experiments and MEA tests. While different catalysts may require a unique modification to the AST protocol, strategies provided in this work enable future in situ and identical-location experiments that will play an important role in the development of robust catalysts for heavy-duty vehicle applications.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Tuning Catalyst Activation and Utilization Via Controlled Electrode Patterning for Low-Loading and High-Efficiency Water Electrolyzers

An anode electrode concept of thin catalyst-coated liquid/gas diffusion layers (CCLGDLs), by integrating Ir catalysts with Ti thin tunable LGDLs with facile electroplating in proton exchange membrane electrolyzer cells (PEMECs), is proposed. The CCLGDL design with only 0.08 mg Ir cm -2 can achieve comparative cell performances to the conventional commercial electrode design, saving ~97% Ir catalyst and augmenting a catalyst utilization to ~24 times. CCLGDLs with regulated patterns enable insight into how pattern morphology impacts reaction kinetics and catalyst utilization in PEMECs. A specially designed two-sided transparent reaction-visible cell assists the in situ visualization of the PEM/electrode reaction interface for the first time. Oxygen gas is observed accumulating at the reaction interface, limiting the active area and increasing the cell impedances. In this work, it is demonstrated that mass transport in PEMECs can be modified by tuning CCLGDL patterns, thus improving the catalyst activation and utilization. The CCLGDL concept promises a future electrode design strategy with a simplified fabrication process and enhanced catalyst utilization. Furthermore, the CCLGDL concept also shows great potential in being a powerful tool for in situ reaction interface research in PEMECs and other energy conversion devices with solid polymer electrolytes.

08 HYDROGEN↗

DOE OSTI2022

Exploring the Impacts of Conditioning on Proton Exchange Membrane Electrolyzers by In Situ Visualization and Electrochemistry Characterization

For a proton exchange membrane electrolyzer cell (PEMEC), conditioning is an essential process to enhance its performance, reproducibility, and economic efficiency. To get more insights into conditioning, a PEMEC with Ir-coated gas diffusion electrode (IrGDE) was investigated by electrochemistry and in situ visualization characterization techniques. The changes of polarization curves, electrochemical impedance spectra (EIS), and bubble dynamics before and after conditioning are analyzed. The polarization curves show that the cell efficiency increased by 9.15% at 0.4 A/cm 2 , and the EIS and Tafel slope results indicate that both the ohmic and activation overpotential losses decrease after conditioning. The visualization of bubble formation unveils that the number of bubble sites increased greatly from 14 to 29 per pore after conditioning, at the same voltage of 1.6 V. Under the same current density of 0.2 A/cm 2 ; the average bubble detachment size decreased obviously from 35 to 25 µm. Furthermore, the electrochemistry and visualization characterization results jointly unveiled the increase of reaction sites and the surface oxidation on the IrGDE during conditioning, which provides more insights into the conditioning and benefits for the future GDE design and optimization.

08 HYDROGEN↗

DOE OSTI2022

Covalent Organic Framework (COF) Derived Ni–N–C Catalysts for Electrochemical CO 2 Reduction: Unraveling Fundamental Kinetic and Structural Parameters of the Active Sites

Electrochemical CO 2 reduction is a potential approach to convert CO 2 into valuable chemicals using electricity as feedstock. Abundant and affordable catalyst materials are needed to upscale this process in a sustainable manner. Nickel-nitrogen-doped carbon (Ni-N-C) is an efficient catalyst for CO 2 reduction to CO, and the single-site Ni-N x motif is believed to be the active site. However, critical metrics for its catalytic activity, such as active site density and intrinsic turnover frequency, so far lack systematic discussion. In this work, we prepared a set of covalent organic framework (COF)-derived Ni-N-C catalysts, for which the Ni-N x content could be adjusted by the pyrolysis temperature. The combination of high-angle annular dark-field scanning transmission electron microscopy and extended X-ray absorption fine structure evidenced the presence of Ni single-sites, and quantitative X-ray photoemission addressed the relation between active site density and turnover frequency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Pt Particle Size Affects Both the Charge Separation and Water Reduction Efficiencies of CdS–Pt Nanorod Photocatalysts for Light Driven H 2 Generation

Decreasing the metal catalyst size into nanoclusters or even single atom is an emerging direction of developing more efficient and cost-effective photocatalytic systems. Because the catalyst particle size affects both the catalyst activity and light driven charge separation efficiency, their effects on the overall photocatalytic efficiency are still poorly understood. Herein, using a well-defined semiconductor–metal heterostructure with Pt nanoparticle catalysts selectively grown on the apexes of CdS nanorods (NRs), we study the effect of the Pt catalyst size on light driven H 2 generation quantum efficiency (QE H 2 ). With the increase of the Pt catalyst size from 0.7 ± 0.3 to 3.0 ± 0.8 nm, the QEH 2 of CdS–Pt increases from 0.5 ± 0.2% to 38.3 ± 5.1%, by nearly 2 orders of magnitude. Transient absorption spectroscopy measurement reveals that the electron transfer rate from the CdS NR to the Pt tip increases with the Pt diameter following a scaling law of d 5.6 , giving rise to the increase of electron transfer efficiency at larger Pt sizes. Additionally, the observed trend can be understood by a simplified kinetic model that assumes the overall efficiency is the product of the quantum efficiencies of charge separation (including hole transfer, electron transfer, and hole scavenging) and water reduction steps, and for CdS–Pt NRs, the quantum efficiencies of electron transfer and water reduction steps increase with the Pt sizes. Our findings suggest the importance of improving the quantum efficiencies of both charge separation and catalysis in designing efficient semiconductor–metal hybrid photocatalysts, especially in the regime of small metal particle sizes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Multi-principal elemental intermetallic nanoparticles synthesized via a disorder-to-order transition

Nanoscale multi-principal element intermetallics (MPEIs) may provide a broad and tunable compositional space of active, high–surface area materials with potential applications such as catalysis and magnetics. However, MPEI nanoparticles are challenging to fabricate because of the tendency of the particles to grow/agglomerate or phase-separated during annealing. Here, we demonstrate a disorder-to-order phase transition approach that enables the synthesis of ultrasmall (4 to 5 nm) and stable MPEI nanoparticles (up to eight elements). We apply just 5 min of Joule heating to promote the phase transition of the nanoparticles into L1 0 intermetallic structure, which is then preserved by rapidly cooling. This disorder-to-order transition results in phase-stable nanoscale MPEIs with compositions (e.g., PtPdAuFeCoNiCuSn), which have not been previously attained by traditional synthetic methods. This synthesis strategy offers a new paradigm for developing previously unexplored MPEI nanoparticles by accessing a nanoscale-size regime and novel compositions with potentially broad applications.

25 ENERGY STORAGE↗

DOE OSTI2021

Nanocolumnar Pt:Ni Alloy Thin Films by High Pressure Sputtering for Oxygen Reduction Reaction

Self-supported nanocolumnar Pt:Ni thin films (TFs) with varying Pt:Ni atomic ratios and Pt mass loadings were produced on a microporous layer (MPL)-like surface composed of carbon particles by high pressure sputtering and examined as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte membrane fuel cells. Cauliflower-like microstructures were observed from scanning electron microscopy imaging. Various Pt:Ni atomic ratios were obtained by simply changing the relative deposition power between Pt and Ni source and investigated by X-ray diffraction and quartz crystal microbalance analysis. Additionally, electrochemical characterization of the Pt:Ni-TF/MPL-like-layer/glassy-carbon samples was conducted through benchtop cyclic voltammetry and rotating disk electrode measurements. The electrochemically active surface area (ECSA) was found to be between 22–42 m 2 g -1 for different Pt:Ni atomic ratios. Lower Pt mass loadings exhibited a higher ECSA and the catalytic activity of all Pt:Ni ratios increased with the increase in Pt mass loading. The ORR activity of the Pt:Ni-TFs increased in the order of 3:1 < 1:1 < 1:3 with exhibiting a specific activity of 1781 μA cm -2 and mass activity of 0.66 A mg -1 for the Ni-rich film with 1:3 ratio. The catalytic performance of Pt:Ni-TFs were higher than traditional high surface area carbon supported Pt nanoparticles, elemental Pt nanorods, and Pt-Ni nanorods.

08 HYDROGEN↗

DOE OSTI2021

Mesoporous Textured Fe-N-C Electrocatalysts as Highly Efficient Cathodes for Proton Exchange Membrane Fuel Cells

A new platinum group metal (PGM)-free proton exchange membrane fuel cell (PEMFC) cathode catalyst materials, synthesized using the VariPore™ method by Pajarito Powder, LLC, are characterized for their structure and activity. The physico-chemical analysis of the iron-nitrogen-carbon (Fe-N-C) electrocatalysts show mesoporous carbon material effectively doped with iron and nitrogen. The materials have an average pore size of 7-8 nm and high specific surface area. The Fe-N-C catalysts exhibit good oxygen reduction reaction (ORR) activity in 0.5 M H2SO4 electrolyte with high half-wave potential and sustainable electrochemical stability over 10,000 repeated potential cycles with insignificant losses in their activities. As cathode catalysts in a PEMFC, the Fe-N-C materials deliver remarkably good fuel cell performance at low overpotential approaching that of the commercial Pt catalyst. The high ORR electrocatalytic activity of these Fe-N-C catalysts is credited to the synergy between nitrogen-moieties, specifically pyrrolic-N, pyridinic-N, and graphitic-N, and iron in addition to the high mesoporosity that facilitate an effective reaction path in boosting the electrocatalytic activity and stability.

DIRECT ENERGY CONVERSION↗

DOE OSTI2021

Slow Auger Recombination of Trapped Excitons Enables Efficient Multiple Electron Transfer in CdS–Pt Nanorod Heterostructures

We report solar-to-fuel conversion reaction often requires multiple proton-coupled electron transfer (PCET) processes powered by the energetic electrons and/or holes generated by the absorption of multiple photons. The effective coupling of multiple electron transfer from the light absorber with the multiple PCET reactions at the catalytic center is one of the key challenges in efficient and selective conversion of solar energy to chemical fuels. In this paper, we examine the dynamics of multiple electron transfer in quantum confined CdS nanorods with a Pt tip, in which the CdS rod functions as the light absorber and the Pt tip the catalytic center. By excitation-fluence-dependent transient absorption spectroscopic measurements, we show that the multiexciton Auger recombination rate in CdS rods follows a carrier-collision model, k n A = n 2 (n – 1)/4k 2 A , with a biexciton lifetime (1/k 2 A ) of 2.0 ± 0.2 ns. In CdS–Pt nanorods, electron transfer kinetics from the CdS conduction band edge to the Pt show negligible dependence on the excitation fluence, occurring with a half-life time of 5.6 ± 0.6 ps. The efficiency of multiple exciton dissociation by multiple electron transfer to Pt decreases from 100% in biexciton states to ~41% at 22 exciton state due to the competition with Auger recombination. The half-lifetime of the n-charge separated state recombination (with n electrons in the Pt and n holes in the CdS) decreases from 10 μs in the single charge separated state to 42 ns in nine charge separated states. Our findings suggest the possibility of driving multielectron photocatalytic reactions under intense illumination and controlling product selectivity through multielectron transfer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗