Engineering Papers⌕ Search

Engineering topics

Cui, Jun

Publications and source records attributed to Cui, Jun.

At least 55 records · Page 3

Overcoming mechanical fragility in Sm-Co permanent magnet materials

Samarium-cobalt alloys are used in some of the strongest permanent magnets, particularly for applications between about 200 and 550°C, but the utilization of these materials is restricted by their brittleness. Improving their mechanical resilience would allow them to be used more widely and, in some cases, substitute for neodymium-based magnet alloys which are subject to supply-chain risks. In this work, we have engineered a series of novel microstructures with bi-modal grain size distributions to achieve unprecedented combinations of mechanical and magnetic properties. Improvements up to 73% are obtained in the flexural strength of Sm 2 (CoFeCuZr) 17 sintered magnets, with negligible impact on the magnetic properties. Our mechanically-robust, high-performance Sm-Co magnets are made without changing the chemical compositions of the materials or their heat treatment procedures, making them highly compatible with existing manufacturing processes.

36 MATERIALS SCIENCE↗

Elastocaloric effect in vanadium (IV) oxide

Elastocaloric cooling utilizes the latent heat associated with stress-induced reversible phase transformations to achieve cooling. Currently, the key barrier to this technology is its prohibitive cost due to the high elastocaloric material cost and the large stress required to drive the cooling cycle. Vanadium (IV) oxide (VO 2 ) is a good candidate, and it is relatively cheap. Our calorimetry study shows it exhibits a reversible phase transformation with a large latent heat of 31.5 J/g, as well as excellent functional stability. Its transformation temperature and latent heat are tunable via heat treatment. We demonstrated that VO 2 powders can be cyclically compressed in a steel tube using a steel plunger to drive the elastocaloric effect. The application of relatively low stress of 300 MPa is sufficient to result in a reversible temperature change of 0.5 °C on the powder compact. Further improvement of reversible temperature change to 1.6 °C under 300MPa is achieved by adding conductive copper powders. Future efforts should focus on improving material properties such as heat capacity and thermal conductivity for candidate ceramic oxides to maximize elastocaloric effects.

36 MATERIALS SCIENCE↗

Electrification Annual Progress Report (FY2019)

During fiscal year 2019 (FY 2019), the U.S. Department of Energy (DOE) Vehicle Technologies Office (VTO) funded early stage research & development (R&D) projects that address Batteries and Electrification of the U.S. transportation sector. The VTO Electrification Sub-Program is composed of Electric Drive Technologies, and Grid Integration activities. The Electric Drive Technologies group conducts R&D projects that advance electric motors and power electronics technologies. The Grid and Charging Infrastructure group conducts R&D projects that advance grid modernization and electric vehicle charging technologies. This document presents a brief overview of the Electrification Sub-Program and progress reports for its R&D projects. Each of the progress reports provide a project overview and highlights of the technical results that were accomplished in FY 2019.

25 ENERGY STORAGE↗

Development of rare-earth-free bulk magnets with energy product up to 12 MGOe in field annealed Mn–Bi–Mg–In–Sb alloys

A treatment consisting of annealing in a moderately strong, ≤30 kOe, magnetic field was applied to arc-melted ingots and compacted melt-spun alloys with composition Mn 50 Bi 50-x-y-z Mg x In y Sb z . The high degree of texture of the magnetic α phase induced with annealing of the ingot samples (except the Mn–Bi–Sb one) allowed for accurate determination of the phase anisotropy field. Alloying was found to increase the anisotropy field from 45 kOe in the Mn 50 Bi 50 alloy to 65 kOe in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 alloy. In the compacted melt-spun alloys subjected to field annealing, a higher degree of texture could be achieved after compaction which had involved less heating, when a smaller fraction of the metastable β' phase had been converted into the α phase; compaction at room temperature allowed for the highest degree of texture in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 magnet. The addition of indium was found to decrease the solidus temperatures of the alloys, facilitating the development of the α phase during the field annealing and modifying the properties of the resulting magnets. Introduction of indium resulted in a higher coercivity H c of the Mn–Bi–Mg–In magnets and in a better texture of the Mn–Bi–Mg–Sn–In magnets. The former effect allowed, in particular, for a viable maximum energy product ( BH ) max of 10 MGOe to be developed in the Mn 50 Bi 46.5 Mg 3 In 0.5 magnet through annealing in a relatively low field of 15 kOe, whereas the latter effect allowed for an excellent combination of ( BH ) max = 11.6 MGOe and H c = 8.5 kOe in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 magnet. The highest ( BH ) max of 12 MGOe was realized in the Mn 50 Bi 46 Mg 3 In 0.5 Sb 0.5 magnet.

36 MATERIALS SCIENCE↗

Synthesis and magnetic performance of gadolinium powder produced with rotating disk atomization

Spherical powder is key for achieving good heat transfer and maintaining low pressure drop for heat transfer fluid in magnetocaloric regenerator. Obtaining relatively large spherical powder of rare earth metals that are extremely sensitive to oxygen is challenging. Comparing to gas atomization and plasma rotating electrode methods, rotating disk atomization (RDA) method is more robust for obtaining a small amount of powder with a short turn-around time, thereby, more suitable for research and development of new magnetocaloric materials. In this work, commercially bulk gadolinium was successfully atomized to produce spherical powder in the targeted 150–250 μm range. The obtained powder exhibited the expected magnetocaloric performance with a maximum change of magnetic entropy of 12.1 J/kg K and a maximum adiabatic temperature change of 12.8 K with an applied magnetic field of 7 T.

36 MATERIALS SCIENCE↗

Fatigue-resistant high-performance elastocaloric materials made by additive manufacturing

Elastocaloric cooling, a solid-state cooling technology, displays the latent heat released and absorbed by stress-induced phase transformations. Hysteresis associated with transformation, however, is detrimental to efficient energy conversion and functional durability. Here, we have created thermodynamically efficient, low-hysteresis elastocaloric cooling materials by means of additive manufacturing of nickel-titanium. The utilization of a localized molten environment and near-eutectic mixing of elemental powders has led to the formation of nanocomposite microstructures composed of a nickel-rich intermetallic compound interspersed among a binary alloy matrix. The microstructure allowed extremely small hysteresis in quasi-linear stress-strain behaviors—enhancing the materials efficiency by a factor of four to seven—and repeatable elastocaloric performance over 1 million cycles. Implementing additive manufacturing to elastocaloric cooling materials enables distinct microstructure control of high-performance metallic refrigerants with long fatigue life.

36 MATERIALS SCIENCE↗

Active magnetic regenerative liquefier using process gas pre-cooling from bypass flow of heat transfer fluid

A process for liquefying a process gas that includes: introducing a heat transfer fluid into an active magnetic regenerative refrigerator apparatus that includes a low magnetic or demagnetized field section; continuously diverting a bypass portion of the heat transfer fluid from a cold side of the low magnetic or demagnetized field section into a bypass flow heat exchanger at a first cold inlet temperature; and continuously introducing the process gas into the bypass flow heat exchanger at a first hot inlet temperature and discharging the process gas or liquid from the bypass flow heat exchanger at a first cold exit temperature; wherein the temperature difference between bypass heat transfer first cold inlet temperature and the process gas first cold exit temperature is 1 to 5 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimizing composition in MnBi permanent magnet alloys

MnBi is an attractive rare-earth-free permanent magnetic material due to its low materials cost, high magnetocrystalline anisotropy (1.6 × 10 6 J m -3 ), and good magnetization (81 emu g -1 ) at room temperature. Although the theoretical maximum energy product (BH) max of 20 MGOe is lower than that of NdFeB-based magnets, the low temperature phase (LTP) of MnBi has a positive temperature coefficient of coercivity, up to 200 °C, which makes it a potential candidate for high temperature applications such as permanent magnet motors. However, the oxygen sensitivity of the MnBi compound and the peritectic reaction between Mn and Bi make it difficult to synthesize into a material with high purity. This challenge is partly offset by adding excess Mn to the alloy, with composition close to Mn 55 Bi 45 resulting in the highest saturation magnetization after common processing techniques such as arc melting, casting, melt spinning, and ball milling. In this paper, we report a systematic process which reduces the amount of excessive Mn, while simultaneously providing a large saturation magnetization (M S ) of 79 emu g -1 at 300 K in the annealed Mn 52 Bi 48 ribbons. We also report excellent magnetic properties in the ball powders, resulting in 0.5–5 µm particles with M S of 75.5 emu g -1 , coercivity H ci of 10.8 kOe, and (BH) max of 13 MGOe using 9 T applied field at 300 K. A secondary annealing treatment on various ball milled powders increased H ci by up to 21%, and also resulted in an increase in M S up to 78.8 emu g -1 .

36 MATERIALS SCIENCE↗

New anisotropic MnBi permanent magnets by field-annealing of compacted melt-spun alloys modified with Mg and Sb

A technique has been designed for manufacturing rare-earth-free MnBi-based magnets capable of filling the existing "gap" between the ferrite and rare-earth permanent magnets. Whereas the earlier approaches relied on sintering of fine and easily degrading single-crystal MnBi particles, the new method achieves refinement of the key α-MnBi phase through melt-spinning combined with appropriate alloying. Modification of the MnBi alloys with Mg and Sb generates a high-coercivity nanostructure of the metastable β' phase. A subsequent compaction at 150 °C produces fully dense materials while converting the β' phase into the stable α phase. Lastly, a short annealing at 265–300 °C in a magnetic field of 3 T increases the fraction of the α phase to 97–98% and aligns the c axes of the α crystallites. A maximum energy product (BH) max of 11.5 MGOe and an intrinsic coercivity Hc of 5.6 kOe have been obtained in a magnet with the nominal composition Mn 50 Bi 46.5 Mg 3 Sb 0.5 . Because the coercivity increases with temperature, the maximum energy product of this magnet is still as high as 8.9 MGOe at 175 °C. Increasing the Sb content to 1.5 at.% increases the H c to 9.3 kOe, but at the same time inhibits the development of the texture thus decreasing the (BH) max . The addition of Mg was found to increase the c lattice parameter of the α phase resulting in an unusually large ratio c/a ≈1.432.

36 MATERIALS SCIENCE↗

In-situ TEM analysis of the phase transformation mechanism of a Cu–Al–Ni shape memory alloy

We report that minimizing phase transformation (PT) hysteresis is of crucial importance for reliability of shape memory alloy (SMA)-based devices, where the lattice strain/stress caused by thermal hysteresis leads to functional degradation. As a result, understanding structural factors that control PT pathway is critical for development of materials with high reversibility. In this study, two distinct PT mechanisms (from γ$'\atop{1}$ martensite to β 1 austenite phase) in Cu–Al–Ni SMAs were revealed by in-situ TEM observation. A growth-dominant conventional PT mechanism shows in the fast quench sample, whereas a nucleation-dominant PT mechanism that suppresses interface propagation and induces high thermal hysteresis displays in the slow quench sample. By characterizing the atomic scale composition and microstructure we discover that slow quenching induces nanoprecipitation that changes chemistry of the matrix alloy, which in turn causes the higher PT hysteresis and temperature, while fast quenching avoids the formation of these nanoprecipitates. Lastly, our finding provides valuable insights into the fabrication of SMAs with better reliability.

36 MATERIALS SCIENCE↗

Compact thermoelastic cooling system

A compact cooling system based on thermoelastic effect is provided. In one embodiment, the system comprises a pair of rollers serving as a heat sink, stress applicator and belt drive, a cold reservoir and a solid refrigerant belt coupled to the cold reservoir and to the heat sinks to pump heat from the cold reservoir to the heat sink. The refrigerant belt comprises solid thermoelastic materials capable of thermoelastic effect. The refrigerant material is mechanically compressed when entering the gap of the roller and subsequently released after passing through. When compressed the refrigerant material transforms to martensite phase and releases heat to the roller and neighboring materials. After released by the rollers, the refrigerant material transforms back to austenite and absorbs heat from the ambient atmosphere.

42 ENGINEERING↗

Propane Liquefaction with an Active Magnetic Regenerative Liquefier

Magnetic refrigeration is a cooling technique that uses the magnetocaloric e?ect (MCE). The active magnetic regenerator (AMR) cycle is a regenerative cycle that employs the MCE and consists of four steps: adiabatic magnetization with no heat transfer gas flow; heat transfer gas flow at constant high field; demagnetization with no heat transfer gas flow; and heat transfer gas flow at constant low field. The first heat transfer gas cold-to-hot flow step rejects heat from the magnetized regenerator to a hot sink and the second reverse heat transfer gas hot-to-cold flow step add heat from a cold source into the demagnetized regenerator. Our primary research and development objective is to use the MCE for more efficient liquefaction of much colder cryogens, to help identify problems of effective coupling of cold heat transfer gas of a single-stage reciprocating magnetic refrigerator to a process gas, we have used a single-stage active magnetic regenerative refrigerator (AMRR) with Gd refrigerant to liquefy pure propane gas at two different supply pressures. The high-purity propane was supplied from a small regulated lecture bottle at 295 K via a 1.6 mm o.d. stainless-steel tube into the helium-cooled coiled-fin tube heat exchanger at 49 psia or 27 psia, to liquefy propane at 262 K or 246 K, respectively. Propane liquefied until the small collection vessel and the coiled fin tube heat exchanger were filled at which the flow from the open lecture bottle stopped. The measured rate of liquefaction and the elapsed time for each case were measured and used to determine the volume of propane collected and the cooling power of the AMRR at the liquefaction temperatures. These cooling power results were compared to the cooling power results obtained from the curve of cool-down temperature vs. time data and agreement was excellent after the duty cycle of each cooling process was properly treated.

propane, liquefaction, active magnetic regenerator↗

Effect of Sb substitution on crystal structure, texture and hard magnetic properties of melt-spun MnBi alloys

Melt-spun Mn 50 Bi 50-x Sb x alloys with x ≤ 5 were prepared at different solidification rates and characterized both in the as-spun state and after annealing. In the as-spun alloys, the Sb substitution leads to the formation of a metastable phase, similar to the binary "quenched high-temperature phase" but without the superstructure of the latter and exhibiting a different – increasing – temperature dependence of coercivity. The new nanocrystalline metastable phase is not only itself characterized by a high room-temperature coercivity (in excess of 20 kOe), but upon annealing it transforms into a high-coercivity (up to 13.5 kOe) "low-temperature" α phase. However, the advantage of obtaining a high coercivity without the otherwise required milling made possible by the Sb substitution is undermined by the absence of a local crystallographic texture in the melt-spun alloys. The best combination of the isotropic hard magnetic properties realized for the Mn 55 Bi 43.5 Sb 1.5 composition is a remanence of 35.5 emu/g and a coercivity of 8.1 kOe. The annealed Sb-free Mn 50 Bi 50 alloys did possess a local crystallographic alignment and, for high solidification rates, a moderate coercivity up to 5.6 kOe; however, they had an inadequate "rectangularity" in the demagnetization curve. The orthorhombic compound known as MnBi 0.9 Sb 0.1 and described earlier as antiferromagnetic was obtained in the annealed ribbons with x ≈ 5. The compound was found to order ferromagnetically between 200 K and ≈250 K and to exhibit a significant coercivity, 14.3 kOe at 50 K. Here, it is suggested that the MnBi 0.9 Sb 0.1 may actually be a Sb-stabilized "new phase" observed earlier as metastable in the Bi–MnBi eutectic alloys.

36 MATERIALS SCIENCE↗

Enabling 6.5% Silicon Electric Steel for Motor Application

Compared to the most widely used 3.2% Si steel, 6.5% Si steel exhibits superior magnetic and electric properties and promises an improvement to the efficiency and power density of electrical machines and transformers. However, due to the heterogeneous formation of B2 and D03 ordered phases, 6.5% Si steel is too brittle to be produced using the traditional cold roll process. And the thin sheet obtained via Si vapor deposition followed by diffusion process is difficult to stamp and assemble. At Iowa State University and Ames Laboratory, a novel process was developed to enable the cost-effective deployment of this brittle materials. The process is developed based on the observation that the deleterious ordered phases can be fully or partially suppressed by rapid cooling. The innovation lies in the production of small ductile flakes using rapid solidification and the consolidation of the obtained flakes directly into a fully dense part with near-net-shape.

36 MATERIALS SCIENCE↗

High current carrying and thermal conductive copper-carbon conductors

The surging demand for miniaturized compact devices has generated the need for new metal conductors with high current carrying ampacity, electric and thermal conductivity. Herein, we report carbon-metal conductors that exhibit a high breakdown current density (39% higher than copper) and electrical conductivity (e.g. 63% higher than that of copper at 363 K) in a broad temperature range. The mechanistic studies of thermal conductivity through first-principle modeling show that the multilayer graphene percolation networks efficiently decrease the electron-phonon coupling in the copper-graphene composites, even if phonon modes are activated at a high temperature. These results imply that the copper-based composites have the potential to be the next generation metal conductor with high electrical and thermal conductivity, as well as excellent current-carrying ampacity. More importantly, the developed composite can be deployed in the ink form, making it possible to be utilized by the microelectronic fabrication process.

Zhang, Wei↗

Performance investigation of a high-field active magnetic regenerator

Regenerative magnetic cycles are of interest for small-scale, high-efficiency cryogen liquefiers; however, commercially relevant performance has yet to be demonstrated. To develop improved engineering prototypes, an efficient modeling tool is required to screen the multi-parameter design space. In this work, we describe an Active Magnetic Regenerative Refrigerator (AMRR) prototype using a high-field superconducting magnet that produces a 100 K temperature span. Using the experimental data, a semi-analytic AMR element model is validated and enhanced system performance is simulated using liquid propane as a heat transfer fluid. In addition, the regenerator composition and fluid flow are simultaneously optimized using a differential evolution algorithm. Simulation results indicate that a natural gas liquefier with a 160 K span and a second-law efficiency exceeding 20% is achievable.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗