Engineering Papers⌕ Search

Engineering topics

Cuddihy, E. F.

Publications and source records attributed to Cuddihy, E. F..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Photovoltaic Module Encapsulation Design and Materials Selection, Volume 1, Abridged

A summary version of Volume 1, presenting the basic encapsulation systems, their purposes and requirements, and the characteristics of the most promising candidate systems and materials, as identified and evaluated by the Flat-Plate Solar Array Project is presented. In this summary version considerable detail and much supporting and experimental information has necessarily been omitted. A reader interested in references and literature citations, and in more detailed information on specific topics, should consult Reference 1, JPL Document No. 5101-177, JPL Publication 81-102, DOE/JPL-1012-60 (JPL), June 1, 1982.

Cuddihy, E. F.↗
NASA NTRS1982

Empirical testing of an analytical model predicting electrical isolation of photovoltaic models

A major design requirement for photovoltaic modules is that the encapsulation system be capable of withstanding large DC potentials without electrical breakdown. Presented is a simple analytical model which can be used to estimate material thickness to meet this requirement for a candidate encapsulation system or to predict the breakdown voltage of an existing module design. A series of electrical tests to verify the model are described in detail. The results of these verification tests confirmed the utility of the analytical model for preliminary design of photovoltaic modules.

Garcia, A., III↗
NASA NTRS1982

Empirical testing of structural deflection modeling of large photovoltaic modules

The objective of the structural deflection test was to verify the analytical models used to predict solar cell stress, load-bearing layer stress, and module deflection that result from a uniform pressure load on the module surface. The verification process consisted of measuring module deflection, stress in the solar cell, and stress in the load-bearing member as a functon of normal pressure load, pottant modulus of elasticity, pottant thickness, and cell location. Four glass superstrate modules, two plain wood substrate modules, two ribbed wood substrate modules, and a steel substrate module were tested. Consistent with analysis predictions, all unribbed specimens exhibited nonlinear load vs. deflection characteristics. With the exception of the steel module, test results and analysis predictions for panel deflectons agreed to within 10 percent. A wider variation of agreement was found for stress in the load-bearing members and cells.

Duncan, L. B.↗
NASA NTRS1981

A quantitative method for photovoltaic encapsulation system optimization

It is pointed out that the design of encapsulation systems for flat plate photovoltaic modules requires the fulfillment of conflicting design requirements. An investigation was conducted with the objective to find an approach which will make it possible to determine a system with optimum characteristics. The results of the thermal, optical, structural, and electrical isolation analyses performed in the investigation indicate the major factors in the design of terrestrial photovoltaic modules. For defect-free materials, minimum encapsulation thicknesses are determined primarily by structural considerations. Cell temperature is not strongly affected by encapsulant thickness or thermal conductivity. The emissivity of module surfaces exerts a significant influence on cell temperature. Encapsulants should be elastomeric, and ribs are required on substrate modules. Aluminum is unsuitable as a substrate material. Antireflection coating is required on cell surfaces.

Garcia, A., III↗
NASA NTRS1981

Rapid solution casting under vacuum of very thick sheets of a segmented polyurethane elastomer

A technique has been developed for rapidly casting from solution under vacuum smooth, bubble-free, clear-white and uniformly thick (about 0.20 cm) sheets of a segmented polyurethane elastomer. The casting is carried out from dimethylformamide solutions inside temperature-controlled air-circulated ovens in order to minimize the establishment of thermal gradients throughout the casting solution. The technique produces quality sheets in 9 days, compared with 40-45 days for an inferior film produced in open pans.

Cuddihy, E. F.↗
NASA NTRS1981

An analytical approach to photovoltaic encapsulation system design

This paper describes a set of analytical methods which have been developed to enable quantitative analysis of encapsulation system designs for terrestrial photovoltaic modules. Design factors determined most important include: encapsulant thickness and modules, emissivity of module surface, ribs on substrate modulus, and AR.

Garcia, A., III↗
NASA NTRS1981

Thermal and optical performance of encapsulation systems for flat-plate photovoltaic modules

The electrical power output from a photovoltaic module is strongly influenced by the thermal and optical characteristics of the module encapsulation system. Described are the methodology and computer model for performing fast and accurate thermal and optical evaluations of different encapsulation systems. The computer model is used to evaluate cell temperature, solar energy transmittance through the encapsulation system, and electric power output for operation in a terrestrial environment. Extensive results are presented for both superstrate-module and substrate-module design schemes which include different types of silicon cell materials, pottants, and antireflection coatings.

Minning, C. P.↗
NASA NTRS1980

Theoretical considerations of soil retention

The performance of solar energy devices is adversely affected by surface soiling, and generally, the loss of performance increases with increases in the quantity of soil retained on their surfaces. To minimize performance losses caused by soiling, solar devices should not only be deployed in low soiling geographical areas, but employ surfaces or surfacing materials having low affinity for soil retention, maximum susceptibility to be naturally cleaned by wind, rain and snow, and to be readily cleanable by simple and inexpensive maintenance cleaning techniques. This article describes known and postulated mechanisms of soil retention on surfaces, and infers from these mechanisms that low soiling and easily cleanable surfaces should have low surface energy, and be hard, smooth, hydrophobic and chemically clean of sticky materials and water soluble salts.

Cuddihy, E. F.↗
NASA NTRS1980

Aging of Magnetic Recording Tape

The paper deals with a study investigating the nature and rates of the hydrolic aging of a wide-band instrumentation magnetic recording tape which employs oxide and backcoat binders made of a polyester urethane elastomer. It was found that the primary mechanism of tape aging and degradation resulted from hydrolysis of its polyester urethane binder.

Cuddihy, E. F.↗
NASA NTRS1979

Vacuum casting of thick polymeric films

Bubble formation and layering, which often plague vacuum-evaporated films, are prevented by properly regulating process parameters. Vacuum casting may be applicable to forming thick films of other polymer/solvent solutions.

Cuddihy, E. F.↗
NASA NTRS1979

Low-cost encapsulation materials for terrestrial solar cell modules

The paper presents the findings of material surveys intended to identify low cost materials which could be functional as encapsulants (by 1986) for terrestrial solar cell modules. Economic analyses have indicated that in order to meet the low cost goal of $2.70 per sq m, some or all of the following material technologies must be developed or advanced: (1) UV screening outer covers; (2) elastomeric acrylics; (3) weatherproofing and waterproofing of structural wood and paper products; (4) transparent UV stabilizers for the UV-sensitive transparent pottants; and (5) cost-effective utilization of silicone and fluorocarbon materials.

Cuddihy, E. F.↗
NASA NTRS1978

Dip-molded t-shaped cannula

Cannula, fabricated out of polyetherurethane, has been designed for long-term service. Improved cannula is T-shaped to collect blood from both directions, thus replacing two conventional cannulas that are usually required and eliminating need for large surgical wound. It is fabricated by using dip-molding process that can be adapted to other elastomeric objects having complex shapes. Dimensions of cannula were chosen to optimize its blood-flow properties and to reduce danger of excessive clotting, making it suitable for continuous service up to 21 days in vein or artery of patient.

Broyles, H. F.↗
NASA NTRS1977

Consideration of encapsulants for photovoltaic arrays in terrestrial applications

Long-term survivability of photovoltaic arrays and components in terrestrial environments will require development of adequate protective systems. Highly considered are polymeric encapsulants, a method which was successfully employed in space and aerospace applications to protect critical electrical circuitry. To be employable, however, the polymer encapsulants must themselves be chemically and mechanically resistant to failure in terrestrial service. Chemical resistance includes stability to the degrading actions of ultraviolet light, oxygen, moisture and elevated temperatures in sun rich areas. Programs are underway to identify and develop chemically stable encapsulant candidates. Chemical considerations aside, mechanical failures of the encapsulants must also be avoided in array designs. This paper discusses design considerations for avoiding mechanical failures of polymeric encapsulants, with emphasis on biaxial properties, thermal fatigue, and anisotropy and nonhomogeneity of material properties. The general principles to be presented evolved from actual failures of polymeric materials in engineering applications. Also included are brief remarks on the permeability of polymer materials to atmospheric gases.

Cuddihy, E. F.↗
NASA NTRS1976

Method of making hollow elastomeric bodies

Annular elastomeric bodies having intricate shapes are cast by dipping a heated, rotating mandrel into a solution of the elastomer, permitting the elastomer to creep into sharp recesses, drying the coated mandrel and repeating the operation until the desired thickness has been achieved. A bladder for a heart assist pump in which a cylindrical body terminating in flat, sharp horizontal flanges fabricated by this procedure has been subjected to over 2,500 hours of simulated life conditions with no visible signs of degradation.

Broyles, H. F.↗
NASA NTRS1976

Hygroscopic Properties of Magnetic Recording Tape

Relative humidity has been recognized as an important environmental factor in many head-tape interface phenomena such as headwear, friction, staining, and tape shed. Accordingly, the relative humidity is usually specified in many applications of tape use, especially when tape recorders are enclosed in hermetically sealed cases. Normally, the relative humidity is believed regulated by humidification of the fill gas to the specification relative humidity. This study demonstrates that the internal relative humidity in a sealed case is completely controlled by the time-dpendence of the hygroscopic properties of the pack of magnetic recording tape. Differences are found in the hygroscopic properties of the same brand of tape, which apparently result from aging, and which may have an effect on the long-term humidity-regulating behavior in a sealed case, and on the occurrence of head-tape interface phenomena from the long-term use of the tape. Results are presented on the basic hygroscopic properties of magnetic tape, its humidity-regulating behavior in a sealed case, and a theoretical commentary on the relative humidity dependence of head-wear by tape, is included.

Cuddihy, E. F.↗
NASA NTRS1974

Analytical investigations employing dynamic mechanical properties

Dynamic mechanical spectroscopy has emerged as an effective laboratory method for analytical investigations of polymers. These methods were applied in investigating the property changes of silicone poppets implanted in artificial heart valves, and for exploring the cause of hardening of certain solid propellants. As a research activity, the property-structure relations which lead to the ability to superimpose dynamic data for epoxy resins were investigated.

Cuddihy, E. F.↗
NASA NTRS1973

Long-time dynamic compatibility of elastomeric materials with hydrazine

The tensile property surfaces for two elastomeric materials, EPT-10 and AF-E-332, were generated in air and in liquid hydrazine environments using constant strain rate tensile tests over a range of temperatures and elongation rates. These results were used to predict the time-to-rupture for these materials in hydrazine as a function of temperature and amount of strain covering a span of operating times from less than a minute to twenty years. The results of limited sheet-folding tests and their relationship to the tensile failure boundary are presented and discussed.

Coulbert, C. D.↗