Engineering topics

Cronin, D. L.

Publications and source records attributed to Cronin, D. L..

5 records

NASA NTRS1985

Aerodynamic-structural study of canard wing, dual wing, and conventional wing systems for general aviation applications

An analytical aerodynamic-structural airplane configuration study was conducted to assess performance gains achievable through advanced design concepts. The mission specification was for 350 mph, range of 1500 st. mi., at altitudes between 30,000 and 40,000 ft. Two payload classes were studied - 1200 lb (6 passengers) and 2400 lb (12 passengers). The configurations analyzed included canard wings, closely coupled dual wings, swept forward - swept rearward wings, joined wings, and conventional wing tail arrangements. The results illustrate substantial performance gains possible with the dual wing configuration. These gains result from weight savings due to predicted structural efficiencies. The need for further studies of structural efficiencies for the various advanced configurations was highlighted.

Selberg, B. P.↗

NASA NTRS1985

Estimating the weight of generally configured dual wing systems

Formulas available for the weight estimation of monoplane wings cannot be said to be appropriate for the estimation of generally configured dual wing systems. In the present paper a method is described which simultaneously generates a structural weight estimate and a fully stressed, quasi-optimal structure for a model of a dual wing system. The method is fast and inexpensive. It is ideally suited to preliminary design. To illustrate the method, a dual wing system and a conventional wing system are sized. Numerical computation is shown to be suitably fast for both cases and, for both cases, convergence to a final configuration is shown to be quite rapid. To illustrate the validity of the method, a conventional wing is sized and its weight obtained by the present method is compared to its weight determined by a reputable weight estimation formula. The results are shown to be very close.

Cronin, D. L.↗

NASA NTRS1980

Aerodynamic-structural analysis of dual bladed helicopter systems

The aerodynamic and structural feasibility of the birotor blade concept is assessed. The inviscid flow field about the dual bladed rotor was investigated to determine the aerodynamic characteristics for various dual rotor blade placement combinations with respect to blade stagger, gap, and angle of attack between the two blades. The boundary layer separation on the rotors was studied and three dimensional induced drag calculations for the dual rotor system are presented. The thrust and power requirements of the rotor system were predicted. NASTRAN, employed as the primary modeling tool, was used to obtain a model for predicting in plane bending, out of plane bending, and the torsional behavior of the birotors. Local hub loads, blade loads, and the natural frequencies for the birotor configuration are discussed.

Selberg, B. P.↗

NASA NTRS1973

Development of a uninterrupted power system: ac and dc to dc converter

This program covered the design, fabrication and testing of an advanced development model uninterrupted power system. The input and output requirements imposed on the power processor were specified such that the unit is electrically interchangeable with existing power systems used by the Federal Aviation Administration in installations which have a history of failure due to electrical transient conditions. Input power is from either of two single-phase ac power sources or batteries with electronic selection and transfer between power sources. Battery reconditioning is automatic when either ac source is present. The output power is rated at 84OW; the nominal output is 24V at 35A. Within the 84OW limit, the regulated output voltage is adjustable from 22V to 30Vdc. Protection against continuous overloading or short circuit is provided. The unit is packaged in a standard 19-inch rack mount configuration with 7-inch panel height. Controls are on the front panel with power input and output through connectors on the rear surface. Cooling is by free convection from fin areas located on the side and rear panels. The packaged unit weighs 52.8 lbs., which can be reduced significantly if a three-phase ac power source is used.

Cronin, D. L.↗

NASA NTRS1971

Criteria for vibration testing

Systematic application of response spectral analysis and other analyses determine damping sensitivity of flight environment and candidate laboratory tests. Computerized comparison is made between response spectrum for flight environment, or enveloping spectra for collection of flight events, and response spectrum for candidate laboratory test.

Cronin, D. L.↗