Engineering Papers⌕ Search

Engineering topics

Coy, J. J.

Publications and source records attributed to Coy, J. J..

82 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Experimental and Analytical Load-Life Relation for AISI 9310 Steel Spur Gears

Life tests were conducted at three different loads with three groups of 8.9 cm pitch diameter spur gears made of vacuum arc remelted VAR AISI 9310 steel. Life was found to vary inversely with load to the 4.3 and 5.1 power at the L10 sub and L50 sub life levels, respectively. The Weibull slope varied linearly with maximum Hertz contact stress, having an average value of 2.5. The test data when compared to AGMA standards showed a steeper slope for the load-life diagram.

Townsend, D. P.↗
NASA NTRS1977

Experimental and analytical load-life relation for AISI 9310 steel spur gears

Life tests were conducted at three different loads with three groups of 8.9 cm, pitch diameter spur gears made of vacuum arc remelted AISI 9310 steel. Life was found to vary inversely with load to the 4.3 and 5.1 power at the L-10 and L-50 life levels, respectively. The Weibull slope varied linearly with maximum Hertz contact stress, having an average value of 2.5. The test data when compared to AGMA standards showed a steeper slope for the load-life diagram.

Townsend, D. P.↗
NASA NTRS1977

Life analysis of restored and refurbished bearings

An analysis of the potential life of refurbished and restored bearings was performed. The sensitivity of 10-percent life and mean-time-between-failure to the effects of cumulative fatigue damage and the amount of stressed volume removed in the restoration process were examined. A modified Lundberg-Palmgren theory was used to predict that the expected 10-percent life of a restored bearing, which is dependent on the previous service time and the volume of material removed from the race surfaces, can be between 74 and 100 percent of the new bearing life. Using renewal theory, it is found that the mean time between failure ranged from 90 to 100 percent of that for a new bearing.

Coy, J. J.↗
NASA NTRS1976

Fatigue life analysis for traction drives with application to a toroidal type geometry

A contact fatigue life analysis for traction drives was developed which was based on a modified Lundberg-Palmgren theory. The analysis was used to predict life for a cone-roller toroidal traction drive. A 90-percent probability of survival was assumed for the calculated life. Parametric results were presented for life and Hertz contact stress as a function of load, drive ratio, and size. A design study was also performed. The results were compared to previously published work for the dual cavity toroidal drive as applied to a typical compact passenger vehicle drive train. For a representative duty cycle condition wherein the engine delivers 29 horsepower at 2000 rpm with the vehicle moving at 48.3 km/hr (30 mph) the drive life was calculated to be 19,200 km (11 900 miles).

Coy, J. J.↗
NASA NTRS1976

OH-58 helicopter transmission failure analysis

The OH-58 main transmission gearbox was run at varying output torques, speeds, and oil cooling rates. The gearbox was subsequently run to destruction by draining the oil from the gearbox while operating at a speed of 6200 revs per minute and 36,000 inch-pounds output torque. Primary cause of gearbox failure was overheating and melting of the planet bearing aluminum cages. Complete failure of the gearbox occurred in 28 1/2 minutes after the oil pressure dropped to zero. The alternating and maximum stresses in the gearbox top case were approximately 10 percent of the endurance limit for the material. Deflection of the bevel gear at 67000 inch-pounds output torque indicate a marginal stiffness for the bevel gear supporting system.

Townsend, D. P.↗
NASA NTRS1975

Dynamic capacity and surface fatigue life for spur and helical gears

A mathematical model for surface fatigue life of gear, pinion, or entire meshing gear train is given. The theory is based on the statistical approach used by Lundberg and Palmgren for rolling-element bearings. Also equations are presented which give the dynamic capacity of the gear set. The dynamic capacity is the transmitted tangential load which gives a 90 percent probability of survival of the gear set for one million pinion revolutions. The analytical results were compared with test data for a set of AISI 9310 spur gears operating at a maximum Hertz stress of 1.71 billion N per sq m (248,000 psi) and 10,000 rpm. The theoretical life predictions were very good when material constants obtained from rolling-element bearing tests were used in the gear life model.

Coy, J. J.↗
NASA NTRS1975

Analysis of dynamic capacity of low-contact-ratio spur gears using Lundberg-Palmgren theory

A concise mathematical model is developed for surface fatigue life of low-contact-ratio spur gears. The expected fatigue life of the pinion, gear, or gear sets may be calculated from the model. An equation for the dynamic capacity of the gear set was also derived in terms of the transmitted tangential tooth load which will give a 10-percent fatigue life of one million pinion revolutions. The theoretical life was compared with experimental data for a set of VAR AISI 9310 gears operating at a Hertz stress of 1.71X10 to the 9th power newtons per square meter (248,000 psi) and 10 000 revolutions per minute. Good agreement was obtained between the experimental and theoretical surface fatigue life of the gears.

Coy, J. J.↗
NASA NTRS1975

Life analysis of helical gear sets using Lundberg-Palmgren theory

A mathematical model is developed for surface fatigue life of helical gears. The expected fatigue life of a pinion, gear, or gear set may be calculated from the model. An equation for the dynamic capacity of a gear set was also derived. Dynamic capacity is the transmitted tangential load which gives a 90 percent probability of survival of the gear set for one million pinion revolutions. The equations, when simplified by setting the helix angle to zero, reduce to the results which were previously developed for spur gears. A sample calculation is given which illustrates the use of the new fatigue life model.

Coy, J. J.↗
NASA NTRS1975

Dynamic Capacity and Surface Fatigue Life for Spur and Helical Gears

A mathematical model for surface fatigue life of gear, pinion, or entire meshing gear train is given. The theory is based on a previous statistical approach for rolling-element bearings. Equations are presented which give the dynamic capacity of the gear set. The dynamic capacity is the transmitted tangential load which gives a 90 percent probability of survival of the gear set for one million pinion revolutions. The analytical results are compared with test data for a set of AISI 9310 spur gears operating at a maximum Hertz stress of 1.71 billion N/sq m and 10,000 rpm. The theoretical life predictions are shown to be good when material constants obtained from rolling-element bearing tests were used in the gear life model.

Coy, J. J.↗