Engineering topics

Covell, Peter F.

Publications and source records attributed to Covell, Peter F..

25 records · Page 2

NASA NTRS1989

Flow-field characteristics and normal-force correlations for delta wings from Mach 2.4 to 4.6

An experimental investigation has been conducted to determine the upper-surface flowfield types and the normal-force characteristics of a series of delta wing models at supersonic speeds. Flow-visualization data were used to classify the flowfields into seven primary types: shockless attached flow, separation bubble, classical vortex, vortex with shock, shock with no separation, shock-induced separation, and separation bubble with shock. The pressure distributions were integrated to obtain upper and lower surface normal-force loadings. A minimal effect of sweep was observed on the upper-surface normal force at constant Mach number and a minimal effect of Mach number was noted for the 75 deg delta wing lower-surface normal force. The normal-force coefficients for all test conditions were correlated, and a single empirical equation was formulated from which the normal-force coefficient could be calculated as a function of Mach number, angle of attack, and wing aspect ratio.

Covell, Peter F.↗

NASA NTRS1988

Configuration trade and code validation study on a conical hypersonic vehicle

A study has been conducted on a generic wing-cone transatmospheric vehicle at Mach numbers form 2.5 to 4.5. The objectives of the study were to experimentally define the aerodynamic characteristics of the vehicle and evaluate several computational aerodynamic prediction methods through comparison with the experimental results. The baseline wing-cone configuration fuselage consisted of a 5 deg half-angle cone forebody, cylindrical midbody, and 9 deg truncated cone afterbody. The 4-percent-thick diamond airfoil wing had an aspect ratio of 1. Several configuration variables were investigated to provide trade information on canard, wing-position and incidence, vertical tail, and nose bluntness effects. Results of the study show that wing-position and wing-incidence effects on the longitudinal aerodynamic characteristics can be significantly influenced by wing-body interference. The use of positive wing incidence to provide favorable forebody orientation for possible inlet performance improvement is accompanied by trim drag and lift-drag ratio penalties. The lateral-directional stability characteristics were strongly influenced by the location of the vertical tails. The higher-order full-potential method provided better estimates of the aerodynamic characteristics than either the linearized supersonic potential method or the tangent-cone/tangent-wedge/shock-expansion on method.

Covell, Peter F.↗

NASA NTRS1987

Molecular flow velocity using Doppler shifted Raman spectroscopy

Measurements of molecular flow velocity, static pressure, and translational temperature in the free-stream of a supersonic wind tunnel and behind the shock of a simple model are reviewed. Based on the free-stream demonstration using inverse Raman spectroscopy, an experiment is outlined to investigate the lee-side flow field above a swept delta wing and simulated spectra expected for the leading-edge vortex are included. The extension of the technique to hypersonic wind tunnels is also explored through the use of simulated spectra.

Exton, Reginald J.↗

NASA NTRS1987

Investigation of leading-edge flap performance on delta and double-delta wings at supersonic speeds

An investigation of the aerodynamic performance of leading-edge flaps on three clipped delta and three clipped double-delta wing planforms with aspect ratios of 1.75, 2.11, and 2.50 was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.90, and 2.16. A primary set of fullspan leading-edge flaps with similar root and tip chords were investigated on each wing, and several alternate flap planforms were investigated on the aspect-ratio-1.75 wings. All leading-edge flap geometries were effective in reducing the drag at lifting conditions over the range of wing aspect ratios and Mach numbers tested. Application of a primary flap resulted in better flap performance with the double-delta planform than with the delta planform. The primary flap geometry generally yielded better performance than the alternate flap geometries tested. Trim drag due to flap-induced pitching moments was found to reduce the leading-edge flap performance more for the delta planform than for the double-delta planform. Flow-visualization techniques showed that leading-edge flap deflection reduces crossflow shock-induced separation effects. Finally, it was found that modified linear theory consistently predicts only the effects of leading-edge flap deflection as related to pitching moment and lift trends.

Covell, Peter F.↗

NASA NTRS1987

Investigation of the vortex flap concept on a 75-deg sweep delta wing at supersonic speeds

An experimental investigation of the aerodynamic performance of vortex flaps on a 75-deg sweep delta wing has been conducted in the NASA Langley Unitary Plan Wind Tunnel at Mach numbers from 1.7 to 2.8. The sharp leading edge vortex flaps consisted of the outboard 30 percent of the local wing semispan. Flap deflections of 0, 5, 10, and 15 deg were investigated, for both a wing-alone and a wing-body configuration. The flaps were effective in reducing the drag across the lift-coefficient range. Integration of the upper surface pressure distributions showed that the suction pressures induced by the vortex on the flap were responsible for the drag reductions. At some lift conditions, the minimum drag condition permitted hinge line separation or vortex migration inboard of the hinge line. This result is in contrast to subsonic results, where optimum conditions call for no hinge line separation. The magnitude of the drag reduction due to flap deflection generally decreased as Mach number increased. The effect of a cylindrical forebody on the drag reduction due to flap deflection was minimal.

Covell, Peter F.↗

NASA NTRS1987

Flow visualization model of the leeside flows over conically cambered delta wings at supersonic speeds

Surface pressure, flow visualization, and force-and-moment data have been obtained for four, variously conically-cambered delta wing models in a range of flow conditions, with a view to leeside flow mechanisms. The influences exerted by Mach number, angle-of-attack, and camber are determined. An analysis of photographic data leads to the analysis of 12 distinctive leeside flow types, which are further categorizable into two groups respectively possessing either one or two dominant features in the leeside flow field: in the former, either the leading edge or hinge line are the originators of the dominant feature; in the latter, both the leading edge and hinge line are generators.

Wood, Richard M.↗

NASA NTRS1986

Effects of winglets on a first-generation jet transport wing. 7: Sideslip effects on winglet loads and selected wing loads at subsonic speeds for a full-span model

The effect of sideslip on winglet loads and selected wing loads was investigated at high and low subsonic Mach numbers. The investigation was conducted in two separate wind tunnel facilities, using two slightly different 0.035-scale full-span models. Results are presented which indicate that, in general, winglet loads as a result of sideslip are analogous to wing loads caused by angle of attack. The center-of-pressure locations on the winglets are somewhat different than might be expected for an analogous wing. The spanwise center of pressure for a winglet tends to be more inboard than for a wing. The most notable chordwise location is a forward center-of-pressure location on the winglet at high sideslip angles. The noted differences between a winglet and an analogous wing are the result of the influence of the wing on the winglet.

Meyer, Robert R., Jr.↗