Engineering topics

Costello, Daniel J., Jr.

Publications and source records attributed to Costello, Daniel J., Jr..

At least 37 records · Page 2

NASA NTRS1991

Multi-stage decoding of multi-level modulation codes

Various types of multi-stage decoding for multi-level modulation codes are investigated. It is shown that if the component codes of a multi-level modulation code and types of decoding at various stages are chosen properly, high spectral efficiency and large coding gain can be achieved with reduced decoding complexity. Particularly, it is shown that the difference in performance between the suboptimum multi-stage soft-decision maximum likelihood decoding of a modulation code and the single-stage optimum soft-decision decoding of the code is very small, only a fraction of dB loss in signal to noise ratio at a bit error rate (BER) of 10(exp -6).

Lin, Shu↗

NASA NTRS1991

Error control techniques for satellite and space communications

Research activities related to error control techniques for satellite and space communication are reported. Specific areas of research include: coding gains for bandwidth efficient codes, hardware implementation of a bandwidth efficient coding scheme for the Hubble Space Telescope, construction of long trellis codes for use with sequential decoding, performance analysis of multilevel trellis codes, and M-algorithm decoding of trellis codes. Each topic is discussed in a corresponding paper that appears in the appendices.

Costello, Daniel J., Jr.↗

NASA NTRS1991

Error control techniques for satellite and space communications

Shannon's capacity bound shows that coding can achieve large reductions in the required signal to noise ratio per information bit (E sub b/N sub 0 where E sub b is the energy per bit and (N sub 0)/2 is the double sided noise density) in comparison to uncoded schemes. For bandwidth efficiencies of 2 bit/sym or greater, these improvements were obtained through the use of Trellis Coded Modulation and Block Coded Modulation. A method of obtaining these high efficiencies using multidimensional Multiple Phase Shift Keying (MPSK) and Quadrature Amplitude Modulation (QAM) signal sets with trellis coding is described. These schemes have advantages in decoding speed, phase transparency, and coding gain in comparison to other trellis coding schemes. Finally, a general parity check equation for rotationally invariant trellis codes is introduced from which non-linear codes for two dimensional MPSK and QAM signal sets are found. These codes are fully transparent to all rotations of the signal set.

Costello, Daniel J., Jr.↗

NASA NTRS1990

New multi-level codes over GF(q)

Set partitioning to multi-dimensional signal spaces over GF(q), particularly GF sup q-1(q) and GF sup q (q), and show how to construct both multi-level block codes and multi-level trellis codes over GF(q). Two classes of multi-level (n, k, d) block codes over GF(q) with block length n, number of information symbols k, and minimum distance d sub min greater than or = d, are presented. These two classes of codes use Reed-Solomon codes as component codes. They can be easily decoded as block length q-1 Reed-Solomon codes or block length q or q + 1 extended Reed-Solomon codes using multi-stage decoding. Many of these codes have larger distances than comparable q-ary block codes, as component codes. Low rate q-ary convolutional codes, work error correcting convolutional codes, and binary-to-q-ary convolutional codes can also be used to construct multi-level trellis codes over GF(q) or binary-to-q-ary trellis codes, some of which have better performance than the above block codes. All of the new codes have simple decoding algorithms based on hard decision multi-stage decoding.

Wu, Jiantian↗

NASA NTRS1990

A hybrid M-algorithm/sequential decoder for convolutional and trellis codes

The Viterbi Algorithm (VA) is optimum in the sense of being maximum likelihood for decoding codes with a trellis structure. However, since the VA is in fact an exhaustive search of the code trellis, the complexity of the VA grows exponentially with the constraint length upsilon. This limits its application to codes with small values of upsilon and relatively modest coding gains. The M-Algorithm (MA) is a limited search scheme which carries forward M paths in the trellis, all of the same length. All successors of the M paths are extended at the next trellis depth, and all but the best M of these are dropped. Since a limited search convolutional decoder will flounder indefinitely if one of the paths in storage is not the correct one, the data are usually transmitted in blocks. It has been shown that the performance of the MA approaches the VA at high signal to noise ratios (SNR's) with an M which is far less than the 2 sup upsilon states in the full trellis. Thus the MA can be used with larger values of upsilon, making larger coding gains possible at high SNR's. However, it still requires a relatively large fixed computational effort to achieve good performance.

Wang, Fu-Quan↗

NASA NTRS1990

Multi-level trellis coded modulation and multi-stage decoding

Several constructions for multi-level trellis codes are presented and many codes with better performance than previously known codes are found. These codes provide a flexible trade-off between coding gain, decoding complexity, and decoding delay. New multi-level trellis coded modulation schemes using generalized set partitioning methods are developed for Quadrature Amplitude Modulation (QAM) and Phase Shift Keying (PSK) signal sets. New rotationally invariant multi-level trellis codes which can be combined with differential encoding to resolve phase ambiguity are presented.

Costello, Daniel J., Jr.↗

NASA NTRS1990

Error control techniques for satellite and space communications

An expurgated upper bound on the event error probability of trellis coded modulation is presented. This bound is used to derive a lower bound on the minimum achievable free Euclidean distance d sub (free) of trellis codes. It is shown that the dominant parameters for both bounds, the expurgated error exponent and the asymptotic d sub (free) growth rate, respectively, can be obtained from the cutoff-rate R sub O of the transmission channel by a simple geometric construction, making R sub O the central parameter for finding good trellis codes. Several constellations are optimized with respect to the bounds.

Costello, Daniel J., Jr.↗

NASA NTRS1990

Trellis-coded multidimensional phase modulation

A 2L-dimensional multiple phase-shift keyed (MPSK) (L x MPSK) signal set is obtained by forming the Cartesian product of L two-dimensional MPSK signal sets. A systematic approach to partitioning L x MPSK signal sets that is based on block coding is used. An encoder system approach is developed. It incorporates the design of a differential precoder, a systematic convolutional encoder, and a signal set mapper. Trellis-coded L x 4PSK, L x 8PSK, and L x 16PSK modulation schemes are found for L = 1-4 and a variety of code rates and decoder complexities, many of which are fully transparent to discrete phase rotations of the signal set. The new codes achieve asymptotic coding gains up to 5.85 dB.

Pietrobon, Steven S.↗

NASA NTRS1989

Bandwidth efficient coding for fading channels - Code construction and performance analysis

The authors apply a general method of bounding the event error probability of trellis-coded modulation schemes to fading channels and use the effective length and the minimum-squared-product distance to replace the minimum-free-squared-Euclidean distance as code design parameters for Rayleigh and Rician fading channels with a substantial multipath component. They present 8-PSK trellis codes specifically constructed for fading channels that outperform equivalent codes designed for the additive white Gaussian noise channel when v is greater than or equal to 5. For quasiregular trellis codes there exists an efficient algorithm for evaluating event error probability, and numerical results on Pe which demonstrate the importance of the effective length as a code design parameter for fading channels with or without side information have been obtained. This is consistent with the case for binary signaling, where the Hamming distance remains the best code design parameter for fading channels. The authors show that the use of Reed-Solomon block codes with expanded signal sets becomes interesting only for large values of E(s)/N(0), where they begin to outperform trellis codes.

Schlegel, Christian↗

NASA NTRS1989

Error control techniques for satellite and space communications

Two aspects of the work for NASA are examined: the construction of multi-dimensional phase modulation trellis codes and a performance analysis of these codes. A complete list is contained of all the best trellis codes for use with phase modulation. LxMPSK signal constellations are included for M = 4, 8, and 16 and L = 1, 2, 3, and 4. Spectral efficiencies range from 1 bit/channel symbol (equivalent to rate 1/2 coded QPSK) to 3.75 bits/channel symbol (equivalent to 15/16 coded 16-PSK). The parity check polynomials, rotational invariance properties, free distance, path multiplicities, and coding gains are given for all codes. These codes are considered to be the best candidates for implementation of a high speed decoder for satellite transmission. The design of a hardware decoder for one of these codes, viz., the 16-state 3x8-PSK code with free distance 4.0 and coding gain 3.75 dB is discussed. An exhaustive simulation study of the multi-dimensional phase modulation trellis codes is contained. This study was motivated by the fact that coding gains quoted for almost all codes found in literature are in fact only asymptotic coding gains, i.e., the coding gain at very high signal to noise ratios (SNRs) or very low BER. These asymptotic coding gains can be obtained directly from a knowledge of the free distance of the code. On the other hand, real coding gains at BERs in the range of 10(exp -2) to 10(exp -6), where these codes are most likely to operate in a concatenated system, must be done by simulation.

Costello, Daniel J., Jr.↗

NASA NTRS1989

High rate concatenated coding systems using multidimensional bandwidth-efficient trellis inner codes

A concatenated coding system using two-dimensional trellis-coded MPSK inner codes and Reed-Solomon outer codes for application in high-speed satellite communication systems was proposed previously by the authors (1989). The authors extend their results to systems using symbol-oriented, multidimensional, trellis-coded MPSK inner codes. The concatenated coding systems are divided into two classes according to their achievable effective information rates. The first class uses multidimensional trellis-coded 8-PSK inner codes and achieves effective information rates around 1 b/dimension (spectral efficiency 2 b/s/Hz). The second class employs multidimensional trellis-coded 16-PSK inner codes and provides effective information rates around 1.5 b/dimension (spectral efficiency 3 b/s/Hz). Both classes provide significant coding gains over an uncoded reference system with the same effective information rate as the coded system. The results show that the symbol-oriented nature of multidimensional inner codes can provide an improvement of up to 1 dB in the overall performance of a concatenated coding system when these codes replace bit-oriented two-dimensional codes.

Deng, Robert H.↗

NASA NTRS1989

An algorithm for computing the distance spectrum of trellis codes

A class of quasiregular codes is defined for which the distance spectrum can be calculated from the codeword corresponding to the all-zero information sequence. Convolutional codes and regular codes are both quasiregular, as well as most of the best known trellis codes. An algorithm to compute the distance spectrum of linear, regular, and quasiregular trellis codes is presented. In particular, it can calculate the weight spectrum of convolutional (linear trellis) codes and the distance spectrum of most of the best known trellis codes. The codes do not have to be linear or regular, and the signals do not have to be used with equal probabilities. The algorithm is derived from a bidirectional stack algorithm, although it could also be based on the Viterbi algorithm. The algorithm is used to calculate the beginning of the distance spectrum of some of the best known trellis codes and to compute tight estimates on the first-event-error probability and on the bit-error probability.

Rouanne, Marc↗

NASA NTRS1989

Parity retransmission hybrid ARQ using rate 1/2 convolutional codes on a nonstationary channel

A parity retransmission hybrid automatic repeat request (ARQ) scheme is proposed which uses rate 1/2 convolutional codes and Viterbi decoding. A protocol is described which is capable of achieving higher throughputs than previously proposed parity retransmission schemes. The performance analysis is based on a two-state Markov model of a nonstationary channel. This model constitutes a first approximation to a nonstationary channel. The two-state channel model is used to analyze the throughput and undetected error probability of the protocol presented when the receiver has both an infinite and a finite buffer size. It is shown that the throughput improves as the channel becomes more bursty.

Lugand, Laurent R.↗

NASA NTRS1989

High rate concatenated coding systems using bandwidth efficient trellis inner codes

High-rate concatenated coding systems with bandwidth-efficient trellis inner codes and Reed-Solomon (RS) outer codes are investigated for application in high-speed satellite communication systems. Two concatenated coding schemes are proposed. In one the inner code is decoded with soft-decision Viterbi decoding, and the outer RS code performs error-correction-only decoding (decoding without side information). In the other, the inner code is decoded with a modified Viterbi algorithm, which produces reliability information along with the decoded output. In this algorithm, path metrics are used to estimate the entire information sequence, whereas branch metrics are used to provide reliability information on the decoded sequence. This information is used to erase unreliable bits in the decoded output. An errors-and-erasures RS decoder is then used for the outer code. The two schemes have been proposed for high-speed data communication on NASA satellite channels. The rates considered are at least double those used in current NASA systems, and the results indicate that high system reliability can still be achieved.

Deng, Robert H.↗

NASA NTRS1989

Error control techniques for satellite and space communications

The performance of bandwidth efficient trellis codes on channels with phase jitter, or those disturbed by jamming and impulse noise is analyzed. An heuristic algorithm for construction of bandwidth efficient trellis codes with any constraint length up to about 30, any signal constellation, and any code rate was developed. Construction of good distance profile trellis codes for sequential decoding and comparison of random coding bounds of trellis coded modulation schemes are also discussed.

Costello, Daniel J., Jr.↗

NASA NTRS1988

A lower bound on the minimum Euclidean distance of trellis-coded modulation schemes

A lower bound on the minimum free Euclidean distance of trellis-coded modulation (TCM) is derived that guarantees the existence of good TCM codes of any complexity. The bound is used to compare trellis codes combined with phase-shift keying, pulse amplitude modulation, and quadrature amplitude-shift keying modulation. This random coding bound is the first lower bound on the free distance of trellis codes, is tighter than any upper bound for large constraint lengths, and predicts the asymptotic performance of TCM when the complexity of the code becomes large. The bound can be used with any code rate and any modulation scheme and shows that the free distance increases linearly with the constraint length for large values of the constraint length.

Rouanne, Marc↗

NASA NTRS1988

Error control techniques for satellite and space communications

During the period December 1, 1987 through May 31, 1988, progress was made in the following areas: construction of Multi-Dimensional Bandwidth Efficient Trellis Codes with MPSK modulation; performance analysis of Bandwidth Efficient Trellis Coded Modulation schemes; and performance analysis of Bandwidth Efficient Trellis Codes on Fading Channels.

Costello, Daniel J., Jr.↗

NASA NTRS1988

Capacity and cutoff rate calculations for a concatenated coding system

A model is developed for a concatenated coding system, and from it the overall channel cutoff rate and capacity is found using random coding arguments. The effects of interleaving between the inner and outer codes and of the availability of side information to the outer decoder are considered. The performance of several specific concatenated coding systems is calculated and used for comparison with the random coding results. From the analysis, a number of general conclusions regarding the design of concatenated coding systems are presented. All the results are derived assuming a block inner code.

Herro, Mark A.↗