Engineering topics

Corsiglia, V. R.

Publications and source records attributed to Corsiglia, V. R..

At least 19 records

NASA NTRS1984

Aerodynamic characteristics of the 40- by 80/80- by 120-foot wind tunnel at NASA Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams are discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗

NASA NTRS1984

Aerodynamic characteristics of the 40- by 80-/80- by 120-ft wind tunnel at NASA-Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams and discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗

NASA NTRS1981

Full-scale wind-tunnel study of wing-fuselage interaction and comparison with paneling method

Full-scale wind-tunnel tests, conducted to determine the effects of three different airfoil sections on the aft-fuselage drag of a low-wing aircraft, are described. The measurements indicate a maximum difference in aft fuselage drag between the three airfoils of about 0.002. Measured changes in the locations of the fuselage pressure contours with airfoil section correlated well with the changes predicted by a three dimensional paneling code. A criterion, based on the inviscid computer code, is then proposed as an indicator for possible adverse viscous interactions at the wing-fuselage juncture.

Ross, J. C.↗

NASA NTRS1981

Full-scale aerodynamic characteristics of a propellar installed on a small twin-engine aircraft wing panel

Full-scale measurements of shaft thrust and torque were made. Wind-tunnel speeds and blade angles were set for full-scale flight conditions. Excellent quality measurements were obtained of the thrust coefficient, the power coefficient, and the propeller efficiency for various values of the advance ratio and the blade incidence angle at 3/4-blade radius. A conventional propeller theory found in the literature was applied to the present results. Although thrust, power, and efficiency were somewhat overpredicted, the advance ratio for maximum efficiency was predicted quite accurately. It was found that, for some conditions, spinner drag could be significant. A simple correction that was based on the spinner base pressure substantially accounted for the changes in efficiency that resulted from this cause.

Barlow, P. R.↗

NASA NTRS1981

Wind-tunnel measurements of wing-canard interference and a comparison with various theories

Wind-tunnel tests and analyses of the aerodynamics of wing-canard combinations for low speed applications are presented. Systematic tests are conducted in a 7 x 10 wind tunnel to explore various combinations of wing-canard vertical and horizontal positioning. The goals of the tests are (1) to investigate potential improved stalling characteristics over conventional tail-aft configurations, (2) to investigate the existence of a lift coefficient advantage, and (3) to determine induced drag levels. The measurements obtained are compared with calculations made using the Prandtl-Munk theory, and with a vortex-lattice panel code. Results indicate that the panel code gives excellent results for lift and induced drag at moderate lift coefficient, whereas Prandtl-Munk theory gives conservative results for induced drag. The application is a light transport aircraft used for short-haul operations.

Feistel, T. W.↗

NASA NTRS1981

Full-scale study of the cooling system aerodynamics of an operating piston engine installed in a light aircraft wing panel

Measurements of the drag and of the nacelle internal pressures on a wing and nacelle that housed a horizontally opposed piston engine were made in the 40- by 80-Foot Wind Tunnel at Ames Research Center. These tests are follow-ons to earlier tests made with the same wing and nacelle but in which the engine was replaced with an electric motor and an adjustable orifice plate. In the initial tests the orifice plate was used to control the rate of cooling-air flow through the nacelle and thereby to simulate a range of gasoline engine types. Good agreement was found between the results of those tests and of the test reported here. Also, the upper and lower plenum pressure and cooling-air flow rate were found to be related by conventional equations used to represent the flow through orifices. Tests were run with three cooling air inlet sizes over a free-stream velocity range from 50 to 150 knots, an angle of attack range from 0 deg to 10 deg, and a cowl-flap deflection range from 0 deg to 30 deg. The data were analyzed by computing a flow coefficient similar to that used in the analysis of orifices. It was found that all of the flow coefficient values fell within a band that varied linearly with inlet area. The linear mean line through this band provides an estimate of the relationship between cooling-air flow rate and upper plenum pressure over a wide range of test conditions.

Corsiglia, V. R.↗

NASA NTRS1980

Effect of propeller slipstream on the drag and performance of the engine cooling system for a general aviation twin-engine aircraft

The pressure recovery of incoming cooling air and the drag associated with engine cooling of a typical general aviation twin-engine aircraft was investigated experimentally. The semispan model was mounted vertically in the 40- by 80-Foot Wind Tunnel at Ames Research Center. The propeller was driven by an electric motor to provide thrust with low vibration levels for the cold-flow configuration. It was found that the propeller slipstream reduces the frontal air spillage around the blunt nacelle shape. Consequently, this slipstream effect promotes flow reattachment at the rear section of the engine nacelle and improves inlet pressure recovery. These effects are most pronounced at high angles of attack, that is, climb condition. For the cruise condition those improvements were more moderate.

Katz, J.↗

NASA NTRS1980

Study of cooling air inlet and exit geometries for horizontally opposed piston aircraft engines

A semispan wing and nacelle of a typical general aviation twin-engine aircraft was tested to evaluate the cooling capability and drag of several nacelle shapes; the nacelle shapes included cooling air inlet and exit variations. The tests were conducted in the Ames Research Center's 40- by 80-Foot Wind Tunnel. It was found that the cooling air inlet geometry of opposed piston engine installations has a major effect on inlet pressure recovery, but only a minor effect on drag. Exit location showed a large effect on drag, especially for those locations on the sides of the nacelle where the suction characteristics were based on interaction with the wing surface pressures.

Katz, J.↗

NASA NTRS1979

Full-scale wind tunnel study of nacelle shape on cooling drag

Tests were made in the NASA-Ames 40- by 80 Foot Wind Tunnel of a wing semispan with a nacelle (no propeller) from a typical, general aviation twin-engine aircraft. Measurements were made of the effect on drag of the cooling air flow through the nacelle. Internal and external nacelle pressures were measured. It was found that the cooling flow accounts for about 13% of the estimated airplane drag and about 42% of the cooling flow drag is associated with the internal flow. It was concluded that improvements could be made by relocating both the inlet and the outlet of the cooling air.

Corsiglia, V. R.↗

NASA NTRS1978

Laser-velocimeter surveys of merging vortices in a wind tunnel: Complete data and analysis

The merger of two corotating vortices was studied with a laser velocimeter designed to measure the two cross-stream components of velocity. Measurements were made at several downstream distances in the vortex wake shed by two semispan wings mounted on the wind-tunnel walls. The velocity data provided wall-defined contours of crossflow velocity, stream function, and vorticity for a variety of test conditions. Downstream of the merger point, the vorticity was found to be independent of the downstream distance for radii smaller than r/b = 0.05. For larger radii, the vorticity depended on the distance from the wing. Upstream of the merger, a multicell vorticity pattern was found.

Corsiglia, V. R.↗

NASA NTRS1978

Hot-wire, laser anemometer and force balance measurements of cross-sectional planes of single and interacting trailing vortices

Single and multiple trailing vortices shed from semi-span wings and a transport model in a wind tunnel were studied by means of a laser-velocimeter, hot-wire anemometer, and a trailing model incorporating a 6-component force balance. Velocity profile and turbulence data from the laser-velocimeter and hot-wire anemometer are presented and shown to compare well with the Betz inviscid circulation model. Lift and rolling moment measurements on the following model are compared with those predicted from the flow field measurements.

Iversen, J. D.↗

NASA NTRS1978

Laser-velocimeter surveys of merging vortices in a wind tunnel

The merger of two vortices was studied with a laser velocimeter designed to measure the two cross-stream components of velocity. Measurements were made at several downstream distances in the vortex wake shed by two semispan wings mounted on the wind tunnel walls. The velocity data provided well difined contours of cross-flow velocity, stream function and vorticity. Downstream of the merger point the vorticity was shown to be independent of the downstream distance for small radii, and at larger radii was dependent on the distance from the wing rather than from the merger point. Upstream of the merger point a multicell vorticity pattern was shown.

Corsiglia, V. R.↗

NASA NTRS1977

Aircraft wake-vortex minimization by use of flaps

A survey was made of research on the alleviation of the trailing vortex hazard by altering span loading with flaps on the generator airplane. Flap configurations of the generator that shed multiple vortices were found to have wakes that dispersed by vortex merging and sinusoidal instability. Reductions of approximately 50 percent in both the wake rolling moment imposed on a following aircraft and the aircraft separation requirement were achieved in the ground based and flight test experiments by deflecting the trailing edge flaps more inboard than outboard. Significantly, this configuration did not increase the drag or vibration on the generating aircraft compared to the conventional landing configuration. Ground based results of rolling moment measurement and flow visualization are shown, using a water tow facility, an air tow facility, and a wind tunnel. Flight test results are also shown, using a full scale B-747 airplane. General agreement was found among the results of the various ground based facilities and the flight tests.

Corsiglia, V. R.↗

NASA NTRS1976

Investigating complex aerodynamic flows with a laser velocimeter

The application of the laser velocimeter in the study of two highly complex aerodynamic flows is discussed. In the first experiment, the laser velocimeter was used with frequency tracking electronics to survey the multiple vortex wake structure behind a model of a large jet transport. The second application is to the study of the induced instantaneous inflow velocities near the blades of a model helicopter rotor; counter-type processing was used in these measurements. In each experiment, the data output channels of these processors were handled in an on-line fashion, including both velocity computations and the plotting of fully reduced data.

Orloff, K. L.↗

NASA NTRS1976

Scanning laser-velocimeter surveys and analysis of multiple vortex wakes of an aircraft

A laser velocimeter capable of rapidly scanning a flow field while simultaneously sensing two components of the velocity was used to measure the vertical and streamwise velocity structure 1.5 spans downstream in the wake of a model typical of a large subsonic transport (Boeing 747). This flow field was modeled by a superposition of axisymmetric vortices with finite cores. This theoretical model was found to agree with the measured velocities everywhere except where two vortices were in close proximity. Vortex strengths derived from the span loading on the wing as predicted by vortex-lattice theory also agree with the present measurements. The axisymmetric vortex model used herein is a useful tool for analytically investigating the vortex wakes of aircraft.

Corsiglia, V. R.↗

NASA NTRS1976

Wind-Tunnel Investigation of the Effect of Porous Spoilers on the Wake of a Subsonic Transport Model

Tests were conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel to determine how porosity of wing spoilers on a B-747 airplane would affect the rolling moments imposed on an aircraft following in the wake. It was found that spoilers with 40 percent porosity and hole diameter to thickness ratio of 1.1 were just as effective in reducing the rolling moment imposed on the follower as solid spoilers, for the case of two spoilers per wing panel (6.4 percent semispan each) with a following model whose span was 20 percent of the span of the generator. When a larger following model was tested, whose span was 50 percent of that of the generator, the effectiveness of the two spoilers per wing was substantially reduced.

Corsiglia, V. R.↗

NASA NTRS1976

Investigating complex aerodynamic flows with a laser velocimeter

The paper discusses the application of the laser velocimeter in the study of two highly complex aerodynamic flows. In the first experiment, the laser velocimeter has been used with frequency tracking electronics to survey the multiple vortex wake structure behind a model of a large jet transport. The second application is to the study of the induced instantaneous inflow velocities near the blades of a model helicopter rotor; counter type processing was used in these measurements. In each experiment, the data output channels of these processors were handled in an on-line fashion, including both velocity computations and the plotting of fully reduced data.

Orloff, K. L.↗

NASA NTRS1975

Experimental study of the effect of span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-Foot Wind Tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗