Exploration of Shear-Dominated Geometries for Material Characterization and Model Calibration; Part 2: Calibration.
Abstract not provided.
Corona, Edmundo↗
Engineering topics
Corona, Edmundo
Publications and source records attributed to Corona, Edmundo.
Power Law Hardening Fit for Inconel 718 Material
The objective of this work is to create an accurate elastic-plastic J2 plasticity model calibration for the Inconel 718 material at room temperature for use in finite element models. This calibration was made using a power-law hardening model of form σ = σ y + $Aε^{n}_{p}$ where A and n are empirically determined constants, and σ y is the proportional limit.
36 MATERIALS SCIENCE↗
Response of 304L stainless steel and 6061-T651 aluminum alloy at -40 °C
The objective of this work is to extend the thermal-mechanical, elastic-plastic calibrations for 304L stainless steel [1] and and 6061-T651 aluminum alloy [2] to the regime between room temperature and -40 °C. The basis to extend the calibration consisted of new uniaxial tension tests conducted at -40 °C using the same plate material stocks, circular cylindrical specimen geometries and testing apparatus as previously, followed by attempts to fit power-law hardening functions to replicate the response observed in the specimens and then extend the yield, hardening constant, hardening exponent and rate constant functions in the calibrations to cover the new temperature regime.
36 MATERIALS SCIENCE↗
Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 6061-T651 Aluminum Alloy from Plate
Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The matters of interest here are the elastic-plastic response and ductile failure behavior of 6061-T651 aluminum alloy under the conditions described above. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of a modular $J_2$ plasticity model with isotropic hardening as well as a ductile failure model. Both included modules that accounted for temperature and strain rate dependence. The models were coupled with an adiabatic heating module to calculate the temperature rise due to the conversion of plastic work to heat. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s as well as four geometries of notched tension specimens and two tests on specimens with shear-dominated deformations. The test data collected allowed the calibration of both the plasticity and the ductile failure models. Most test specimens were extracted from a single piece of plate to maintain consistency. Notched tension tests came from a possibly different plate, but from the same lot. When using the model in structural finite element calculations, element formulations and sizes different from those used to model the test specimens in the calibration are likely to be used. A brief investigation demonstrated that the failure model can be particularly sensitive to the element selection and provided an initial guide to compensate in a specific example.
36 MATERIALS SCIENCE↗
Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 304L Stainless Steel Alloy
Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The material of interest here is 304L stainless steel, and the objective of this work is to calibrate thermal-mechanical models: one for the constitutive behavior and another for failure. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of the models. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s. It also included notched tension and shear-dominated compression hat tests specifically designed to calibrate the failure model. All test specimens were extracted from a single piece of plate to maintain consistency. The constitutive model adopted was a modular $J_2$ plasticity model with isotropic hardening that included rate and temperature dependence. A criterion for failure initiation based on a critical value of equivalent plastic strain fitted the failure data appropriately and was adopted. Possible ranges of the values of the parameters of the models were determined partially on historical data from calibrations of the same alloy from other lots and are given here. The calibration of the parameters of the models were based on finite element simulations of the various material tests using relatively ne meshes and hexahedral elements. When using the model in structural finite element calculations, however, element formulations and sizes different from those in the calibration are likely to be used. A brief investigation demonstrated that the failure initiation predictions can be particularly sensitive to the element selection and provided an initial guide to compensate for the effect of element size in a specific example.
36 MATERIALS SCIENCE↗
Empirical Formula for Puncture Energy of Flat Metal Plates by a Cylindrical Flat Punch
Impact problems of plate-like parts by punch-like objects with relatively large mass moving at slow speeds of a few feet per second constitute a subset of impact problems of interest at Sandia. This is in contrast to small objects moving in the range of hundreds or thousands of feet per second or higher. The objective of this work is to develop a simple formula that can be used to estimate a lower bound for the puncture energy of metal plates impacted by cylindrical, essentially rigid punches of circular cross-section and at nose. Such geometry is used as a basis in the design of puncture mitigation barriers or procedures. This was accomplished by deriving an expression using non-dimensional analysis and then calibrating it based on tests results in the range of speeds of interest. Lower bounds can then be determined based on confidence intervals or factors of safety.
36 MATERIALS SCIENCE↗