Engineering Papers⌕ Search

Engineering topics

Cornelius, Aaron

Publications and source records attributed to Cornelius, Aaron.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Optimization of an aerostructural machining process using physics-guided Bayesian stability modelling

Existing algorithms for predicting milling chatter have not been widely adopted in industry since they require specialized instruments to measure the stability inputs. This study describes how the machining process for a meter-scale aluminum aerostructure was optimized using a physics-guided Bayesian stability model. The study was performed in collaboration with an industrial partner on production machines to evaluate the practicality of the proposed method under real-world conditions. For each cutting tool, the Bayesian approach automatically selected a small number of cutting tests, which were monitored using a microphone to observe the chatter frequency. The algorithm learned the system dynamics, cutting forces, and stability map from these test results. A novel algorithm for predicting tool bending stress was incorporated into the test selection algorithm to avoid tool breakage. On average, each set of optimized cutting parameters required less than six tests to identify and were 97% more productive than baseline parameters from the cutting tool manufacturer. The machining program was then further optimized using commercial feedrate scheduling software to remove cutting force spikes and reduce air cutting time. Five components were machined using the optimized process. These results demonstrate the potential for physics-guided Bayesian models to improve productivity in industrial settings.

Cornelius, Aaron [UT Knoxville]↗
DOE OSTI2024

Process damping identification using Bayesian learning and time domain simulation

Process damping can provide improved machining productivity by increasing the stability limit at low spindle speeds. However, existing methods for identifying process damping models experimentally require specialized setups and/or multiple cutting tests. While the phenomenon is well known, the modeling challenges limit pre-process parameter selection that leverages the potential increases in material removal rates. This paper proposes a physics-informed Bayesian method that can identify the cutting force and process damping models from a limited set of test cuts without requiring direct measurements of cutting force or vibration. The method uses time domain simulation to incorporate process damping and provide a basis for test selection. Here, new strategies for efficient sampling and dimensionality reduction are applied to lower computation time and minimize the effect of model error. The proposed method is demonstrated and the identified cutting and damping force coefficients are compared to values obtained using machining tests and least-squares fitting.

42 ENGINEERING↗
DOE OSTI2024

Using GANs to predict milling stability from limited data

Milling is a key manufacturing process that requires the selection of operating parameters that provide efficient performance. However, the presence of chatter, a self-excited vibration causing poor surface finish and potential damage to the machine and cutting tool, makes it challenging to select the appropriate parameters. To predict chatter, stability maps are commonly used, but their generation requires expensive data, making it difficult to employ these maps in industry. Therefore, there is a pressing need for an approach that can accurately predict stability maps using limited experimental data. This study introduces the new Encoder GAN (EGAN) approach based on Generative Adversarial Networks (GANs) that predicts stability maps using limited experimental data. The approach consists of the encoder, generator, and discriminator subnetworks and uses the trained encoder and generator to predict the target stability map. This versatile method can be applied to various tool setups and can accurately predict stability maps with limited experimental data (five to 10 cutting tests) even when there is little information available for unknown parameters. In conclusion, the study evaluates the proposed approach using both numerical data and experiments and demonstrates its superior performance compared to state-of-the-art benchmarks.

42 ENGINEERING↗
DOE OSTI2023

Structured light scanning artifact-based performance study

Structured light scanning is used to create a digital twin of a manufactured part, where features are extracted to determine if the part meets the designer’s intent and required tolerances. This paper describes repeatability and reproducibility analyses for a commercially-available structured light scanning system and measurement artifact. The repeatability study used five repeated scans at 15 measurement positions. Repeatability was assessed by randomly selecting one of the five scans at each of the 15 positions and creating a part mesh. This process was performed 50 times and the statistics for the dimension variations were calculated to isolate the scanning effects only. The same sequence was then performed for 10 of the 15 positions and five of the 15 positions to evaluate the repeatability sensitivity to the number of measurement positions. Reproducibility was assessed by selecting 15 positions to create a mesh and repeating the 15-position measurement sequence 10 times using different positions for each mesh construction. The statistics for the dimension variations were then calculated. This incorporated the effects of both scanning and the position and orientation of the part relative to the scanner. This sequence was repeated for 10-position and five-position scans to evaluate the corresponding sensitivity. Finally, the artifact dimensions from structured light scanning were compared to coordinate measuring machine measurements of the same features.

42 ENGINEERING↗
DOE OSTI2022

Hybrid manufacturing of Invar mold for carbon fiber layup using structured light scanning

This paper describes coordinate system definition and transfer for five-axis machining of additively-manufactured preforms. In this method, a set of fiducials are attached to the temporarily attached to the part, and their location relative to the preform geometry is calibrated using a structured light scanner. Those fiducials can then be measured in the machine tool to determine the location and orientation of the part. The method is demonstrated by finish-machining a carbon fiber layup mold from an additively manufactured Invar preform. In addition to showing the coordinate transfer methods necessary to machine the part, several key challenges with machining additively-manufactured preforms are discussed and potential solutions are proposed. Unfortunately, the final part was ultimately unusable due to porosity inside the part left from the additive process. Future work will remanufacture this part while taking steps to avoid porosity and other challenges encountered.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A machining digital twin for hybrid manufacturing

Hybrid manufacturing consisting of metal additively manufactured preforms and computer numerical control (CNC) machining has been established to be an effective method for high material use rates. However, hybrid manufacturing introduces unique challenges. Near-net shape designs are typically selected, which result in a smaller margin for part placement within the stock and stringent requirements for work coordinate system identification. Additionally, less stock material reduces the preform stiffness, which limits the material removal rates during machining. This paper demonstrates a digital twin for CNC machining of a wire arc additively manufactured preform that implements: 1) structured light scanning for stock model identification and tool path generation; 2) a fused filament fabrication apparatus to attach temporary fiducials and scan targets to the preform that enable coordinate system definition for both the CAM and CNC machine; 3) preform and tool tip frequency response function measurements to enable stable milling parameter selection; and 4) post-manufacturing measurements of geometry, surface finish, and structural dynamics to confirm designer intent. These efforts define key components of the machining digital twin for hybrid manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

America’s Cutting Edge CNC machining and metrology training

This paper describes the workforce development activities supported by America’s Cutting Edge (ACE), a national initiative for machine tool technology development and advancement. ACE is supported by the Department of Defense Industrial Base Analysis and Sustainment (IBAS) program from the Office of Industrial Policy. Both the online and in-person components of the computer numerically controlled (CNC) machining and metrology training programs are summarized and participation information is provided.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Receptance coupling substructure analysis and chatter frequency-informed machine learning for milling stability

This paper describes a milling stability identification approach that simultaneously considers: physics-based models for the tool tip frequency response functions and stability predictions; the binary result from a milling test (automatically labeled as stable or unstable based on frequency content); chatter frequency when an unstable result is obtained; and user risk tolerance. The algorithm applies probabilistic Bayesian machine learning with adaptive, parallelized Markov Chain Monte Carlo sampling to update the probability of stability with each milling test. Furthermore, the result is a robust solution for rapid convergence to optimized milling parameters for maximum metal removal rate using all available information.

42 ENGINEERING↗
DOE OSTI2021

A Bayesian Framework for Milling Stability Prediction and Reverse Parameter Identification

This paper describes a physics-guided Bayesian framework for identifying the milling stability boundary and system parameters through iterative testing. Prior uncertainties for the parameters are identified through physical simulation and literature reviews, without physical testing of the actual milling system. Those uncertainties are then propagated to the stability map using a physics-based stability model, which is used to suggest a test point. The uncertainties are updated based on the new information acquired from the cutting test to form a new probability distribution, called the posterior. Finally, the posterior are compared to measured values for the stability boundary and system parameters to evaluate the approach. Based on experimental observations, the advantages and disadvantages of using a physics-guided model are discussed.

Cornelius, Aaron↗