Engineering PapersSearch

Engineering topics

Corliss, Lloyd D.

Publications and source records attributed to Corliss, Lloyd D..

Piloted simulation study of two tilt-wing flap control concepts, phase 2

A two phase piloted simulation study has been conducted in the Ames Vertical Motion Simulator to investigate alternative wing and flap controls for tilt-wing aircraft. This report documents the flying qualities results and findings of the second phase of the piloted simulation study and describes the simulated tilt-wing aircraft, the flap control concepts, the experiment design and the evaluation tasks. The initial phase of the study compared the flying qualities of both a conventional programmed flap and an innovative geared flap. The second phase of the study introduced an alternate method of pilot control for the geared flap and further studied the flying qualities of the programmed flap and two geared flap configurations. In general, the pilot ratings showed little variation between the programmed flap and the geared flap control concepts. Some differences between the two control concepts were noticed and are discussed in this report. The geared flap configurations had very similar results. Although the geared flap concept has the potential to reduce or eliminate the pitch control power requirements from a tail rotor or a tail thruster at low speeds and in hover, the results did not show reduced tail thruster pitch control power usage with the geared flap configurations compared to the programmed flap configuration. The addition of pitch attitude stabilization in the second phase of simulation study greatly enhanced the aircraft flying qualities compared to the first phase.

Birckelbaw, Lourdes G.

Piloted simulation study of two tilt-wing control concepts

A two-phase piloted simulation study was conducted to investigate alternative wing and flap controls for tilt-wing aircraft. The initial phase of the study compared the flying qualities of both a conventional (programmed) flap and an innovative geared flap. The second phase of the study introduced an alternate method of pilot control for the geared flap and further studied the flying qualities of the programmed flap, and two geared flap configurations. In general, the pilot rating showed little variation between the programmed flap and the geared flap control concepts. Some differences between the two concepts were noticed and are discussed in this paper. The addition of pitch attitude stabilization in the second phase of the study greatly enhanced the aircraft flying qualities. This paper describes the simulated tilt-wing aircraft and the flap control concepts and presents the results of both phases of the simulation study.

Birckelbaw, Lourdes G.

Piloted simulation study of two tilt-wing control concepts

A two phase piloted simulation study was conducted to investigate alternative wing and flap controls for tilt-wing aircraft. The initial phase of the study compared the flying qualities of both a conventional (programmed) flap and an innovative geared flap. The second phase of the study introduced an alternate method of pilot control for the geared flap and further studied the flying qualities of the programmed flap, and two geared flap configurations. In general, the pilot ratings showed little difference between the programmed flap and the geared flap control concepts, although differences between the two control concepts were noticed and are discussed in this paper. The addition of pitch attitude stabilization in the second phase of the study greatly enhanced the aircraft flying qualities. This paper describes the simulated tilt-wing aircraft and the flap control concepts, and presents the results of both the first and second phases of the piloted simulation study.

Birckelbaw, Lourdes G.

Phase II simulation evaluation of the flying qualities of two tilt-wing flap control concepts

A simulation study was initiated to investigate alternative wing and flap controls for tilt-wing aircraft. The initial phase of the study compared the flying qualities of both a conventional (programmed) flap and an innovative geared flap. The second phase of the study, reported in this paper, introduced an alternate method for pilot control of the geared flap and further studied the flying qualities of the programmed flap, and two geared flap configurations. The results showed little difference among the three flap control configurations except during a longitudinal reposition task where the programmed flap configuration was the best. The addition of pitch attitude stabilization greatly enhanced the aircraft handling qualities. This paper describes the tilt-wing aircraft and the flap control concepts, and presents the results of the second simulation experiment.

Birckelbaw, Lourdes G.

Initial piloted simulation study of geared flap control for tilt-wing V/STOL aircraft

A simulation study of a representative tilt wing transport aircraft was conducted in 1990 on the Ames Vertical Motion Simulator. This simulation is in response to renewed interest in the tilt wing concept for use in future military and civil applications. For past tilt wing concepts, pitch control in hover and low-speed flight has required a tail rotor or reaction jets at the tail. Use of mono cyclic propellers or a geared flap have also been proposed as alternate methods for providing pitch control at low speed. The geared flap is a subject of this current study. This report describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, the pilots' evaluation tasks and procedures, and the results obtained from the simulation experiment. The pilot evaluations and comments are also documented in the report appendix.

Guerrero, Lourdes M.

How Safe Is Control Software

Paper examines issue of software safety. Presents four case histories of software-safety analysis. Concludes that, to be safe, software, for all practical purposes, must be free of errors. Backup systems still needed to prevent catastrophic software failures.

Dunn, William R.

Handling Qualities Results of an Initial Geared Flap Tilt Wing Piloted Simulation

An exploratory simulation study of a novel approach to pitch control for a tilt wing aircraft was conducted in 1990 on the NASA-Ames Vertical Motion Simulator. The purpose of the study was to evaluate and compare the handling qualities of both a conventional and a geared flap tilt wing control configuration. The geared flap is an innovative control concept which has the potential for reducing or eliminating the horizontal pitch control tail rotor or reaction jets required by prior tilt wing designs. The handling qualities results of the geared flap control configuration are presented in this paper and compared to the conventional (programmed flap) tilt wing control configuration. This paper also describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, and the pilot evaluation tasks and procedures.

Guerrero, Lourdes M.

Software safety - A user's practical perspective

Software safety assurance philosophy and practices at the NASA Ames are discussed. It is shown that, to be safe, software must be error-free. Software developments on two digital flight control systems and two ground facility systems are examined, including the overall system and software organization and function, the software-safety issues, and their resolution. The effectiveness of safety assurance methods is discussed, including conventional life-cycle practices, verification and validation testing, software safety analysis, and formal design methods. It is concluded (1) that a practical software safety technology does not yet exist, (2) that it is unlikely that a set of general-purpose analytical techniques can be developed for proving that software is safe, and (3) that successful software safety-assurance practices will have to take into account the detailed design processes employed and show that the software will execute correctly under all possible conditions.

Dunn, William R.

RSRA/X-Wing flight control system development - Lessons learned

The X-Wing, in concept, marries the efficiencies of a helicopter and fixed wing aircraft through the use of a four-bladed wing/rotor that can be rotated or stopped in flight. The RSRA/X-Wing flight test program was a technology demonstration of this concept which, after three successful flights, was discontinued in late 1987. In spite of many technical challenges in this program, such as the use of circulation control, the fabrication of a large all-composite rotor, the development of an advanced, quadruplex digital flight control system, and the need for higher harmonic control, no major technical problems had been encountered at the time of the stop-work order. This paper addresses the issues of flight control system development and focuses on lessons learned. As with other such programs, software development was the most consuming issue. Other subjects of discussion include the problems of balancing program goals with technical goals, software- and hard-ware-related problems, safety issues, and system testing.

Corliss, Lloyd D.

Effect of field of view on performing a low altitude maneuvering task

Visual systems with a single window display are often utilized in ground based simulators used to study helicopter flying qualities during visual low altitude maneuvering tasks. The effects of this limited field of view (FOV) on pilot assessments of flying qualities are uncertain. A study was conducted using a variable stability UH-1H helicopter to compare restricted and unrestricted FOV for a range of flying qualities. With the restricted FOV, the pilots reported reduced ground track precision owing to loss of visual contact with the course markers. However, the predictable ground track of the repeated S-turn task with no obstacles made it easy for them to anticipate their maneuvers, and resulted in only a slight degradation of pilot ratings. This degradation was not sensitive to large changes in helicopter flying qualities.

Carico, Dean