Engineering Papers⌕ Search

Engineering topics

Conway, E. J.

Publications and source records attributed to Conway, E. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

A 50-kW Module Power Station of Directly Solar-Pumped Iodine Laser

The conceptual design of a 50 kW Directly Solar-Pumped Iodine Laser (DSPIL) module was developed for a space-based power station which transmits its coherent-beam power to users such as the moon, Martian rovers, or other satellites with large (greater than 25 kW) electric power requirements. Integration of multiple modules would provide an amount of power that exceeds the power of a single module by combining and directing the coherent beams to the user's receiver. The model developed for the DSPIL system conservatively predicts the laser output power (50 kW) that appears much less than the laser output (93 kW) obtained from the gain volume ratio extrapolation of experimental data. The difference in laser outputs may be attributed to reflector configurations adopted in both design and experiment. Even though the photon absorption by multiple reflections in experimental cavity setup was more efficient, the maximum secondary absorption amounts to be only 24.7 percent of the primary. However, the gain volume ratio shows 86 percent more power output than theoretical estimation that is roughly 60 percent more than the contribution by the secondary absorption. Such a difference indicates that the theoretical model adopted in the study underestimates the overall performance of the DSPIL. This fact may tolerate more flexible and radical selection of design parameters than used in this design study. The design achieves an overall specific power of approximately 5 W/kg and total mass of 10 metric tons.

Choi, S. H.↗
NASA NTRS1991

Diode laser power module for beamed power transmission

Recent progress with powerful, efficient, and coherent monolithic diode master-oscillator/power-amplifier (M-MOPA) systems is promising for the development of a space-based diode laser power station. A conceptual design of a 50-kW diode laser power module was made for space-based power stations capable of beaming coherent power to the moon, Martian rovers, or other satellites. The laser diode power module consists of a solar photovoltaic array or nuclear power source, diode laser arrays (LDAs), a phase controller, beam-steering optics, a thermal management unit, and a radiator. Thermal load management and other relevant aspects of the system (such as power requirements and system mass) are considered. The 50-kW power module described includes the highest available efficiency of LD M-MOPA system to date. However, the overall efficiency of three amplifier stages, including the coupling efficiency, turns out to be 55.5 percent. Though a chain of PA stages generates a high-power coherent beam, there is a penalty due to the coupling loss between stages. The specific power of the 50-kW module using solar power is 6.58 W/kg.

Choi, S. H.↗
NASA NTRS1989

Beamed laser power for advanced space missions

Advanced civil space missions may benefit substantially from beamed laser power. Recent advances in solar-pumped lasers and electrically driven diode lasers are discussed. Two laser-beamed power applications, for an advanced space station and in support of a high power lunar base, are summarized.

Conway, E. J.↗
NASA NTRS1989

Laser power transmission concepts for Martian applications

Long-term, highly reliable, flexible power will be required to support many diverse activities on Mars and for rapid development of the Mars environment. The potential of laser power transmission for supporting science, materials processing, transportation, and human habitats is discussed. Some advantageous locations for laser power stations in Mars orbit are developed.

De Young, R. J.↗
NASA NTRS1988

Comparison of electrically driven lasers for space power transmission

High-power lasers in space could provide power for a variety of future missions such as spacecraft electric power requirements and laser propulsion. This study investigates four electrically pumped laser systems, all scaled to 1-MW laser output, that could provide power to spacecraft. The four laser systems are krypton fluoride, copper vapor, laser diode array, and carbon dioxide. Each system was powered by a large solar photovoltaic array which, in turn, provided power for the appropriate laser power conditioning subsystem. Each system was block-diagrammed, and the power and efficiency were found for each subsystem block component. The copper vapor system had the lowest system efficiency (6 percent). The CO2 laser was found to be the most readily scalable but has the disadvantage of long laser wavelength.

Deyoung, R. J.↗
NASA NTRS1988

One-megawatt solar pumped and electrically driven lasers for space power transmission

High power lasers in space could provide power for a variety of future space missions such as spacecraft electric power requirements and laser propulsion. This study investigates four electrically pumped laser systems, krypton fluoride, copper vapor, laser diode array, and the carbon dioxide laser, all scaled to 1-MW laser output. Each system obtained its primary power from a large solar photovoltaic array which, in turn, provides power for the appropriate laser power conditioning subsystem. Each system was block-diagrammed, and the power and efficiency were found for each subsystem. The laser diode array had the highest solar-to-laser efficiency (6 percent) and smallest radiator area making it the most advantageous of the electrically driven lasers studied. This system was then compared with an iodine solar pumped laser system previously studied. The diode array had a better wavelength with regard to transmission optics mass, but it also had a heavier radiator because of its lower temperature radiator requirement. A more advanced solar pumped laser could emerge as the preferred laser system for space applications.

Deyoung, R. J.↗
NASA NTRS1987

Preliminary design and cost of a 1-megawatt solar-pumped iodide laser space-to-space transmission station

A preliminary conceptual design of a space-based solar pumped iodide laser emitting 1 megawatt of laser power for space-to-space power transmission is described. A near parabolic solar collector focuses sunlight onto the t-C4F9I (perfluoro-t butyl iodide) lasant within a transverse flow optical cavity. Using waste heat, a thermal system was designed to supply compressor and auxiliary power. System components were designed with weight and cost estimates assigned. Although cost is very approximate, the cost comparison of individual system components leads to valuable insights for future research. In particular, it was found that laser efficiency was not a dominant cost or weight factor, the dominant factor being the laser cavity and laser transmission optics. The manufacturing cost was approx. two thirds of the total cost with transportation to orbit the remainder. The flowing nonrenewable lasant comprised 20% of the total life cycle cost of the system and thus was not a major cost factor. The station mass was 92,000 kg without lasant, requiring approx. four shuttle flights to low Earth orbit where an orbital transfer vehicle will transport it to the final altitude of 6378 km.

Deyoung, R. J.↗
NASA NTRS1987

Preliminary conceptual design and weight of a one-megawatt space-based laser power station utilizing a solar-pumped iodine lasant

A preliminary conceptual design of a space-based solar-pumped iodide laser emitting 1 MW of laser power for space-to-space power transmission is described. A near-parabolic solar collector focuses sunlight onto the t-C4F9I lasant within a transverse-flow optical cavity. Using waste heat, a thermal system supplies compressor and auxiliary power. The major system components are designed with weight estimates assigned. In particular, it is found that laser efficiency is not a dominant weight factor, the dominant factor being the laser transmission optics. The station mass is 92,000 kg, requiring approximately eight Shuttle flights to LEO, where an orbital transfer vehicle can transport it to the final altitude of 6378 km.

De Young, R. J.↗
NASA NTRS1986

Solar pumped laser technology options for space power transmission

An overview of long-range options for in-space laser power transmission is presented. The focus is on the new technology and research status of solar-pumped lasers and their solar concentration needs. The laser options include gas photodissociation lasers, optically-pumped solid-state lasers, and blackbody-pumped transfer lasers. The paper concludes with a summary of current research thrusts.

Conway, E. J.↗
NASA NTRS1986

Progress in solar-pumped laser research

High-power solar-pumped lasers could eventually provide power in space for electric and propulsive needs. Recent research results are presented showing progress on both direct-pumped and blackbody-pumped solar lasers. Using a solar simulator, lasing of C3F7I at 10 watts has been achieved. Using C4F9I, lasing thresholds as low as 170 solar constants have been demonstrated, which is the lowest threshold value for a solar-pumped gas laser to date. Blackbody-pumped CO2 lasers have achieved outputs of 180 milliwatts for cavity-pumped and 1.4 watts in transfer-pumped systems.

De Young, R. J.↗
NASA NTRS1985

Introduction to the Workshop on Lasant Materials for Blackbody Pumped Lasers

The purpose of this workshop was to define new lasants and transfer gases for blackbody pumped lasers. The goal was to find gases with the correct energies and lifetimes for use as lasants and/or transfer gases. The more immediate goal of the participants was to suggest molecules, currently available, (or to be synthesized) which either satisfy criteria which was developed or which deserve further study because from limited information they seem to satisfy the criteria. Thus, the workshop was interested in the identification of molecules and the rational for suggesting them. There were two basic kinds of blackbody lasers to be discussed, the cavity laser and the transfer laser. The physics of optical absorption and laser emission was addressed. The physics of the transfer laser was discussed. Molecular energy transfer from one molecule to another was added to the concepts already involved in the cavity laser. The physics of the transfer gas and the transfer-lasant gas combinations was also discussed.

Conway, E. J.↗
NASA NTRS1985

Report from the Cavity-Laser Working Group

From the Workshop, a Cavity-Laser Working Group was formed. The goal of this Cavity-Laser Working Group was to propose molecules which might be useful as lasants for blackbody cavity lasers. The approach was to (1) define some rules for the identification of molecules, (2) consider molecules presented at the Workshop and (3) identify additional molecules through the suggestions of attendees. Some evaluation was to be attempted for each molecule considered. A set of criteria was developed, however, sophisticated rules required detailed information which was not available for every molecule. The rules are listed and briefly discussed.

Conway, E. J.↗
NASA NTRS1983

A NASA high-power space-based laser research and applications program

Applications of high power lasers are discussed which might fulfill the needs of NASA missions, and the technology characteristics of laser research programs are outlined. The status of the NASA programs or lasers, laser receivers, and laser propulsion is discussed, and recommendations are presented for a proposed expanded NASA program in these areas. Program elements that are critical are discussed in detail.

Deyoung, R. J.↗
NASA NTRS1983

Preliminary comparison of laser and solar space power systems

Four laser receiver systems are compared to onboard solar photovoltaic power generation for spacecraft electrical requirements. The laser photovoltaic and laser MHD receivers were found to be lighter than a comparable planar solar photovoltaic system. The laser receiver also shows less drag at lower altitudes. Panel area is also reduced for the laser receiver allowing fewer Shuttle trips for construction. Finally, it is shown that a 1 megawatt laser and receiver system might be constructed with less weight than a comparable planar solar photovoltaic system.

Deyoung, R. J.↗
NASA NTRS1982

GaAs solar cells

The major thrusts proposed for GaAs were increased efficiency and improved radiation damage data. Current laboratory production cells consistently achieve 16 percent AMO one-Sun efficiency. The user community wants 18-percent efficient cells as soon as possible, and such a goal is though to be achievable in 2 years with sufficient research funds. A 20-percent research cell is considered the efficiency limit with current technology, and such a cell seems realizable in approximately 4 years. Future efficiency improvements await improved substrates and materials. For still higher efficiencies, concentrator cells and multijunction cells are proposed as near-term directions.

Conway, E. J.↗
NASA NTRS1981

Thermal stability of GaAs heteroface solar cells with differing contact materials

GaAlAs/GaAs heteroface solar cells used in space offer advantages of higher operating temperatures and recovery from radiation damage using thermal annealing. Elevated temperature experiments were conducted to evaluate the electrical stability of cells with different contact materials. These experiments indicate that for operation of GaAs heteroface solar cells at elevated temperatures, front contact metals must be carefully chosen. The short circuit current varied by only about 3% for cells with Pd/Ag contacts that were heated to 240 C for a total of 500 hours. However, a total decrease in the open circuit voltage of about 20% was observed for these cells. After heating cells to 400 C, large changes in open circuit voltage were observed for cells with Pd/Ag, Pd/Au, Pd, Ag, and Ti contacts; however, preliminary results indicate more stable open circuit voltages for cells with Au, Cr, Zn, and Cr/Au contacts.

Friesen, W. J.↗
NASA NTRS1981

A thermochemical model of radiation damage and annealing applied to GaAs solar cells

Calculations of the equilibrium conditions for continuous radiation damage and thermal annealing are reported. The calculations are based on a thermochemical model developed to analyze the incorporation of point imperfections in GaAs, and modified by introducing the radiation to produce native lattice defects rather than high-temperature and arsenic atmospheric pressure. The concentration of a set of defects, including vacancies, divacancies, and impurity vacancy complexes, are calculated as a function of temperature. Minority carrier lifetimes, short circuit current, and efficiency are deduced for a range of equilibrium temperatures. The results indicate that GaAs solar cells could have a mission life which is not greatly limited by radiation damage.

Conway, E. J.↗