Engineering Papers⌕ Search

Engineering topics

Conrad, B.

Publications and source records attributed to Conrad, B..

Comparison of gas analyzers for eddy covariance: Effects of analyzer type and spectral corrections on fluxes

The eddy covariance technique (EC) is used at hundreds of field sites worldwide to measure trace gas exchange between the surface and the atmosphere. Data quality and correction methods for EC have been studied empirically and theoretically for many years. The recent development of new gas analyzers has led to an increase in technological options for users. Open-path (no inlet tube) and closed-path (long inlet tube) sensors have been used for a long time, whereas enclosed-path (short inlet tube) sensors are relatively new. In this work, we tested the comparability of fluxes calculated from five different gas analyzers including two open-path (LI-7500 A from LI-COR, IRGASON from Campbell), two enclosed-path (CPEC200 from Campbell, LI-7200 from LI-COR), and one closed-path (2311-f; from Picarro) analyzers, which were all located on a single tower at an irrigated alfalfa field in Davis, CA. To effectively compare sensors with different tube characteristics we used three different spectral correction methods. We found that all sensors, regardless of type, can be used to measure fluxes if appropriate corrections are applied and quality control measures are taken. However, the comparability strongly depended on the gas (CO 2 or H 2 O) and the correction method. Average differences were below 4% for CO 2 fluxes using any spectral correction method, but for H 2 O average differences were between 4% and 13% for the different methods. The magnitude of corrections also varied strongly, especially for water vapor fluxes. This study does not identify the best sensor, but rather weighs the benefits and difficulties of each sensor and sensor type. Our findings show that enclosed and closed-path gas analyzers that measure water vapor with inlet tubes experience large high frequency attenuation and should be corrected with empirical correction methods. This information presented here about different the diverse sensors be considered by investigators when choosing a sensor for a site or when analyzing EC measurements from multiple sites.

54 ENVIRONMENTAL SCIENCES↗

Flight evaluation of advanced navigation techniques for general aviation using frequency scanning

Experiments on an automatic multisensor navigation concept are being conducted in a Cessna 402B. The test system consists of VOR, DME, and air data sensors controlled by a Hewlett Packard 9820A electronic calculator which processes the data and, by means of a four-state Kalman filter, outputs position and ground and wind velocities to a map display. Novel features which make such a system potentially low-cost include frequency-scanning operation of a single VOR receiver and a single DME transceiver and use of a shed-vortex true airspeed sensor. Results obtained during flight in a local area where six to eight DME NAVAIDS were receivable yielded better than 1/4-mile accuracy.

Jackson, C. T., Jr.↗

Evaluation of several navigation algorithms for application to general aviation

Using data obtained in flight, three position determining algorithms for use by general aviation aircraft were evaluated representing increasing software requirements. These were a DME only, DME/air data and blended DME/air data. Although each step represented additional software with resultant increase in position accuracy, all could be performed on a programmable electronic desk calculator. Results from the computation of aircraft position using the three algorithms are presented. The algorithms employed can be extended to accept VOR, TACAN bearing, ADF, or other NAVAID Data. To obtain the flight data an experimental system was configured and flown on a general aviation aircraft. Principal hardware elements (all with low-cost potential) were a programmable calculator, a single DME receiver (multiplexed for multiple DME use) and a low-cost air speed sensor (shed-vortex principle). The flight test demonstrated satisfactory performance of these principal elements.

Conrad, B.↗

New mechanization equations for aided inertial navigation systems

Inertial navigation equations are developed which use area navigation (RNAV) waypoints and runway references as coodinate centers. The formulation is designed for aided inertial navigation systems and gives a high numerical accuracy through all phases of flight. A new formulation of the error equations for inertial navigation systems is also presented. This new formulation reduces numerical calculations in the use of Kalman filters for aided inertial navigation systems.

Schmidt, S. F.↗

Flight results from a study of aided inertial navigation applied to landing operations

An evaluation is presented of the approach and landing performance of a Kalman filter aided inertial navigation system using flight data obtained from a series of approaches and landings of the CV-340 aircraft at an instrumented test area. A description of the flight test is given, in which data recorded included: (1) accelerometer signals from the platform of an INS; (2) three ranges from the Ames-Cubic Precision Ranging System; and (3) radar and barometric altimeter signals. The method of system evaluation employed was postflight processing of the recorded data using a Kalman filter which was designed for use on the XDS920 computer onboard the CV-340 aircraft. Results shown include comparisons between the trajectories as estimated by the Kalman filter aided system and as determined from cinetheodolite data. Data start initialization of the Kalman filter, operation at a practical data rate, postflight modeling of sensor errors and operation under the adverse condition of bad data are illustrated.

Mcgee, L. A.↗

Washout circuit design for multi-degrees-of-freedom moving base simulators.

A mathematical framework is presented for designing logic to accept motion-dependent parameters from a simulation, attenuating them ('washing them out'), and generating appropriately limited drive signals. This framework is sufficiently general to encompass six-degree-of-freedom simulators with large motion capability. Emphasis is placed on preserving certain motion cue relations (such as those that would be observed in coordinated flight). Strategies for simulating side forces via tilts are shown. Finally, several specific circuits are shown. These circuits have proven to be readily adaptable to a variety of moving-base simulators.

Conrad, B.↗

A comparison of the effects of small nonlinearities on several estimation schemes.

A variety of techniques are available for estimating the states of nonlinear dynamic systems from noisy data. These procedures are generally equivalent when applied to linear systems. This paper investigates the difference between several of these procedures in the presence of small dynamic and observational nonlinearities. In particular, it examines one least square batch processing algorithm, and three recursive algorithms similar to the Kalman filter. To first order, all the estimators have the same covariance. Expressions for the means, however, show that each estimator has a different bias. The examples presented show that the biases can be a strong function of such parameters as initial covariances and number of data points being considered.

Conrad, B.↗

State estimation with small nonlinearities

A variety of techniques is available for estimating the states of nonlinear dynamic systems from noisy data. The differences among several of these procedures in the presence of small dynamic and observational nonlinearities are investigated. Four discrete estimation algorithms are analyzed. The first is a strictly least square estimator, while the others are recursive algorithms similar to the Kalman filter used for estimating the states of linear systems. A group of analytic expressions is developed for the mean and covariance of the error in each of these estimators so that they may be compared without lengthy Monte Carlo simulations. The covariance expressions show that, to first order, all the estimators have the same covariance. Expressions for the means show that each estimator has a different bias. Several examples are carried out demonstrating that the relative magnitudes of the bias errors in the various estimators can be a strong function of such parameters as initial covariances and number of data points. Under some circumstances, more complicated algorithms can have larger biases than smaller ones.

Conrad, B.↗